👉ROLE OF A PLANNING
ENGINEER

⭐️A Planning Engineer ensures every activity is scheduled, monitored, and executed on time.

⏺From planning resources to tracking progress, they keep the project on the right timeline.

📌Prepare project schedule using tools like MS Project / Primavera
📌Plan resources - manpower, materials, machinery
📌 Track daily, weekly, monthly progress
📌 Compare planned vs actual progress
📌ldentify delays and suggest corrective actions
📌Coordinate with site engineers,
Contractors, and management
📌Prepare progress reports, charts, and dashboards
📌Support billing team with quantity tracking
📌 Monitor cost, time, and productivity

@etconp

ታምራት  ፕሌት እና ጄቦልት አቅራቢ

📍ኢትዮጵያ ዉስጥ የትም እንልክሎታለን

0904040477
0911016833

👉In highway construction, every layer plays a crucial role in ensuring strength, stability, and longevity of the pavement.

⭐️Below is the standard layer composition for a flexible pavement structure, designed for performance and durability፡

@etconp 👇

Seal Coat & Tack Coat፡

Applied to provide a smooth surface finish and ensure proper bonding between bituminous layers.

Bituminous Concrete (40 mm)

The wearing course that resists traffic load and provides a durable riding surface.

Dense Bituminous Macadam (80 mm)

Acts as a binder course distributing load to lower layers.

Wet Mix Macadam (250 mm)

Provides structural stability and acts as a strong base layer.

Granular Sub-Base (250 mm)

Ensures adequate drainage and prevents capillary rise of water.

Sub Gravel (200 mm)

Adds additional load-bearing capacity to the substructure.

Embankment (200 mm)

Elevates the road level and provides a stable foundation.

Cleaning and Graveling (200 mm)

The initial preparation ensuring uniformity and compaction at ground level.

@etconp

👉Phases Of Construction Work

1. Site Clearance

Removing unwanted materials such as bushes, trees, debris, topsoil, and obstacles to prepare the land for construction.

2. Excavation

Digging soil for foundations, footings, septic tanks, basements, etc., using manual tools or excavators.

3. Foundation

Constructing the base of the building (like isolated footing, raft, or pile) that safely transfers load to the soil.

4. Plinth Beam

A reinforced concrete beam constructed at the plinth level to tie the foundation walls and prevent differential settlement.

5. Super Structure

All construction above the plinth level—columns, beams, floors, walls, and roof.

6. Brick Works

Building walls using bricks or blocks with mortar to form rooms, partitions, and structural walls.

7. Lintel Work

Casting RCC beams above doors and windows to carry the load of the wall above openings.

8. Slab Construction

Constructing RCC slabs (roof/floor) using shuttering, reinforcement, and concrete.

9. Electric & Plumbing

Installing electrical wiring, switches, DB panels, water supply pipes, sanitary lines, and drainage systems.

10. Interior & Exterior

Internal and external finishing works such as plaster, false ceiling, façade work, wall putty, etc.

11. Flooring

Laying tiles, marble, granite, wooden flooring, or other finishes.

12. Painting

Applying primer, putty, and paint to both interior and exterior surfaces for final appearance and protection.

@etconp

👉SITE MATERIAL CONSUMPTION TRACKING

📌Tracking how much material (cement, steel, sand, bricks, etc.) is received, used, and remaining at site.

⏺Efficient material tracking ensures cost control and smooth project progress.

📌WHY ITS IMPORTANT

-Control wastage
-Save cost
- Plan material in advance
- Keep project records clear

📌TIPS

- Record daily
- Check stock weekly
- Use issue slips for every material
- Compare with estimated quantity

💫Stay organized, stay accurate!

@etconp

👉Small reinforcement mistakes can lead to big structural problems.

💫Always check spacing, cover, laps, bar placement, and tying quality to ensure a safe and durable structure.

📚Common Reinforcement Mistakes

🏷1. Insufficient concrete cover

📌problem

🔗steel too close to surface.

🔗rusts easily.

🏷2. Short lap length

📌problem

🔗overlapping not enough.

🔗weak joints.

🏷3. Rusty or dirty steel

📌problem

🔗reduces bond with concrete.

🏷4. Missing stirrups or ties

📌problem

🔗less resistance to shear.

🏷5.  Wrong bar spacing

📌problem

🔗reduces anchorage bars too close or too far.

🔗weak structure.

🏷6.  Loose binding wires

📌problem

🔗bars shift during concreting.

🏷7.  Wrong bar size

📌problem

🔗affects structural strength.

🏷8. No chairs or spacers

📌problem

🔗bars touch shutter.

🔗poor cover.

🏷9. Removing hooks Reinforcement/bends

📌problem

🔗Reduce anchorage.

🏷10.Reinforcement congestion

📌problems

🔗hard to compact Concrete

🔗honeycombing

@etconp

👉 INTERCON Construction Chemicals 

● Concrete Admixtures
● Bonding Agents
● Waterproofings
● Wall Putty, Prime Coat
● Concrete Repair Mortar
● Floor hardener, Epoxy
● Grout, Self-level mortar
● Quartz paint, Contextra
● Tile Adhesive & Tile Joint Fillers 
● Geotextiles and other construction chemicals and materials

☎️ Tel: 0961955555

🔹 Address 1: Signal road, around
Dinberwa Hospital

🔹 Addres 2: Wellosefer, Infront of
Dani Plaza

👉Reversal of Stresses in Earthquake Load

💫In earthquake-resistant design, understanding how stresses reverse due to seismic loads is crucial.

🏷Buildings are not only subjected to vertical gravity loads but also to dynamic lateral forces during an earthquake. Here's what happens:

🔁 1. Bidirectional Seismic Load

📌Earthquake forces act in both directions (left and right).

📌This leads to alternating tension and compression zones in the columns and beams.

📌Reinforcement detailing must accommodate this reversal.

📊 2. Tension Shift


📌As seismic waves hit from either side, tension zones shift, especially in columns.

📌Ductile detailing becomes essential to absorb this energy without brittle failure.

⚖️ 3.  Gravity Load vs Seismic Load

📌Under gravity load, beams are mostly in tension at the bottom.

📌However, during earthquakes, the tension may appear on top or on the sides.

📌Designs must allow for this reversal of stress zones, especially in critical connections.

📌 Engineers must ensure both columns and beams can withstand reversed tension and compression cycles to prevent collapse.

@etconp

👉Road Super Elevation

💫Super elevation is the tilting of the road surface at a curve so that the outer edge of the pavement is raised above the inner edge.

⏺It helps counteract the effect of centrifugal force on vehicles moving along curved paths.

⭐️Purpose of Super Elevation

❇️To reduce the tendency of vehicles to overturn or skid outward.

❇️To provide comfort and safety to drivers.

❇️To allow vehicles to negotiate curves at higher speeds smoothly.

⚙️ Formula

🔰e + f = V2/127R

🎲Where:

⏺e = rate of super elevation (m/m)

⏺f = lateral friction factor (usually 0.15)

⏺v = speed of vehicle (km/hr)

⏺R = radius of curve (m)

📏 Design Steps

1. Calculate required super elevation using the above formula.

2. Limit the maximum super elevation (generally 1 in 15 to 1 in 20, or 7% for highways).

3. Provide transition length for smooth rise.

🛣️ Methods of Providing Super Elevation

⏹By rotating the pavement about the inner edge.

⏹By raising the outer edge with respect to the center.

⏹By rotating about the center line (commonly used method).

⚠️ Limitations

⚡️Not suitable for urban roads with slow-moving traffic.

⚡️Excessive super elevation can cause problems for slow or parked vehicles.

📍Advantages

⏺Increases vehicle stability.

⏺Reduces side friction demand.

⏺Enhances comfort and safety at curves.

@etconp

👉Steps for Implementing a Potable Water Supply Project:

💫1. Feasibility Study

- Evaluation of potable water needs
- Identification of available water sources

💫2. Project Design

- Design of the water supply network
- Calculation of flow rates and pressures

💫3. Environmental Impact Assessment

- Evaluation of potential environmental impacts
- Development of mitigation measures

💫4. Land Acquisition

- Acquisition of land required for the project
- Compensation of landowners

💫5. Tendering and Contracting

- Preparation of tender documents
- Selection of contractors and award of contracts

💫6. Construction

- Site preparation and excavation
- Installation of pipes and equipment
- Connection to existing network

💫7. Commissioning and Testing

- Verification of water quality

@etconp

👉Objectives of Soil Investigation

💫1. To determine the type and stratification (layers) of soil beneath the site.

💫2. To find out the bearing capacity of the soil how much load it can safely support.

💫3. To determine the depth of the water table (groundwater level).

💫4. To detect any weak or problematic soils (e.g., expansive clay, peat).

💫5. To recommend the most suitable type of foundation (e.g., raft, pad, pile).

💫6. To estimate settlement and stability under loading.

@etconp