👉 INTERCON Construction Chemicals 

● Concrete Admixtures
● Bonding Agents
● Waterproofings
● Wall Putty, Prime Coat
● Concrete Repair Mortar
● Floor hardener, Epoxy
● Grout, Self-level mortar
● Quartz paint, Contextra
● Tile Adhesive & Tile Joint Fillers 
● Geotextiles and other construction chemicals and materials

☎️ Tel: 0961955555

🔹 Address 1: Signal road, around
Dinberwa Hospital

🔹 Addres 2: Wellosefer, Infront of
Dani Plaza

👉Reversal of Stresses in Earthquake Load

💫In earthquake-resistant design, understanding how stresses reverse due to seismic loads is crucial.

🏷Buildings are not only subjected to vertical gravity loads but also to dynamic lateral forces during an earthquake. Here's what happens:

🔁 1. Bidirectional Seismic Load

📌Earthquake forces act in both directions (left and right).

📌This leads to alternating tension and compression zones in the columns and beams.

📌Reinforcement detailing must accommodate this reversal.

📊 2. Tension Shift


📌As seismic waves hit from either side, tension zones shift, especially in columns.

📌Ductile detailing becomes essential to absorb this energy without brittle failure.

⚖️ 3.  Gravity Load vs Seismic Load

📌Under gravity load, beams are mostly in tension at the bottom.

📌However, during earthquakes, the tension may appear on top or on the sides.

📌Designs must allow for this reversal of stress zones, especially in critical connections.

📌 Engineers must ensure both columns and beams can withstand reversed tension and compression cycles to prevent collapse.

@etconp

👉Road Super Elevation

💫Super elevation is the tilting of the road surface at a curve so that the outer edge of the pavement is raised above the inner edge.

⏺It helps counteract the effect of centrifugal force on vehicles moving along curved paths.

⭐️Purpose of Super Elevation

❇️To reduce the tendency of vehicles to overturn or skid outward.

❇️To provide comfort and safety to drivers.

❇️To allow vehicles to negotiate curves at higher speeds smoothly.

⚙️ Formula

🔰e + f = V2/127R

🎲Where:

⏺e = rate of super elevation (m/m)

⏺f = lateral friction factor (usually 0.15)

⏺v = speed of vehicle (km/hr)

⏺R = radius of curve (m)

📏 Design Steps

1. Calculate required super elevation using the above formula.

2. Limit the maximum super elevation (generally 1 in 15 to 1 in 20, or 7% for highways).

3. Provide transition length for smooth rise.

🛣️ Methods of Providing Super Elevation

⏹By rotating the pavement about the inner edge.

⏹By raising the outer edge with respect to the center.

⏹By rotating about the center line (commonly used method).

⚠️ Limitations

⚡️Not suitable for urban roads with slow-moving traffic.

⚡️Excessive super elevation can cause problems for slow or parked vehicles.

📍Advantages

⏺Increases vehicle stability.

⏺Reduces side friction demand.

⏺Enhances comfort and safety at curves.

@etconp

👉Steps for Implementing a Potable Water Supply Project:

💫1. Feasibility Study

- Evaluation of potable water needs
- Identification of available water sources

💫2. Project Design

- Design of the water supply network
- Calculation of flow rates and pressures

💫3. Environmental Impact Assessment

- Evaluation of potential environmental impacts
- Development of mitigation measures

💫4. Land Acquisition

- Acquisition of land required for the project
- Compensation of landowners

💫5. Tendering and Contracting

- Preparation of tender documents
- Selection of contractors and award of contracts

💫6. Construction

- Site preparation and excavation
- Installation of pipes and equipment
- Connection to existing network

💫7. Commissioning and Testing

- Verification of water quality

@etconp

👉Objectives of Soil Investigation

💫1. To determine the type and stratification (layers) of soil beneath the site.

💫2. To find out the bearing capacity of the soil how much load it can safely support.

💫3. To determine the depth of the water table (groundwater level).

💫4. To detect any weak or problematic soils (e.g., expansive clay, peat).

💫5. To recommend the most suitable type of foundation (e.g., raft, pad, pile).

💫6. To estimate settlement and stability under loading.

@etconp