👉በ6 ሰዓታት ውስጥ 2.4 ኪ.ሜ የአስፋልት ንጣፍ ያከናወኑት ቻይናውያን አድስ ሪከርድ አስመዝግቧል

🚧በቤጂንግ የሚገኙ ቻይናውያን የመንገድ ግንባታ ሠራተኞች፤ 2.4 ኪሎ ሜትር ርዝመት ያለውን መንገድ በ6 ሰዓታት ውስጥ ብቻ አስፋልት በማንጠፍ አዲስ ሪከርድ አስመዝግበዋል።

💫በተለምዶ እንዲህ ዓይነቱን የአስፋልት ንጣፍ ሥራ ለማከናወን በርካታ ቀናትን አልፎ ተርፎም ሳምንታትን የሚወስድ ሲሆን፣ ይህም ከፍተኛ የትራፊክ መጨናነቅን ያስከትል ነበር።

⏺ሆኖም እነዚህ ቻይናውያን ባለሙያዎች መንገዱን ለቀናት ከመዝጋት ይልቅ፣ ሥራውን በ6 ሰዓታት ውስጥ ሙሉ በሙሉ አጠናቀዋል።

⏺በሌሎች የዓለም ሀገራት 2.4 ኪሎ ሜትር መንገድን በ24 ሰዓታት ውስጥ ማንጠፍ እንደ ስኬት ቢታይም፣ ይህንን ሥራ በ6 ሰዓታት ውስጥ ብቻ ያጠናቀቀ ከቻይና ውጪ ሌላ ሀገር የለም።

@etconp

👉 INTERCON Construction Chemicals 

● Concrete Admixtures
● Bonding Agents
● Waterproofings
● Wall Putty, Prime Coat
● Concrete Repair Mortar
● Floor hardener, Epoxy
● Grout, Self-level mortar
● Quartz paint, Contextra
● Tile Adhesive & Tile Joint Fillers 
● Geotextiles and other construction chemicals and materials

☎️ Tel: 0961955555

🔹 Address 1: Signal road, around
      Dinberwa Hospital

🔹 Addres 2: Wellosefer, Infront of
     Dani Plaza

ADVERTISMENT

ታምራት ፕሌት እና ጄ ቦልት አቅራቢ

✅የምንሰጣቸው አገልግሎቶች

🔅 ፕሌት any Size & thickness
🔅 ጄ ቦልት (ጥርስ ማዉጣትና ማጠፍ)

🔅 የተለያዩ  [modefic] ስራዎችን እንሰራለን።

♦️ ማንኛዉንም ብረታ ብረት እንገዛለን።

☎️ስልክ 0904040477 ወይም 0911016833 ደውለው ያግኙን
📱ቴሌግራም ላይ ፦https://t.me/heavenic1

አድራሻ፦  ቁ 1.መርካቶ
                ቁ.2 አየር ጤና  ኪዳነ ምህረት

ጥራትና ታማኝነት መለያችን ነው።
ታምራት ፕሌት እና ጄ ቦልት አቅራቢ

👉Practical, engineer-focused guide you can use to design a safe steel water-tank tower (tank-on-tower).

💫Here I’ll cover in ahort; the main factors, the design steps, important checks, and practical recommendations.

1) Define the project (inputs)

Tank capacity & geometry: storage volume (m³), tank diameter D and liquid depth h, tank material and empty tank mass.

Location data: site altitude, basic wind speed, seismic zone / response spectrum, mean annual temperature, frost.

Soil info: allowable bearing pressure, groundwater level.

Access & service: ladder, platform, handrail height, pipe connections, overflow, drainage.

Codes to apply: local building code or recognized standards (EBCS, AISC, Eurocode, IS, etc.) and tank standards (if applicable).

2) Loads to consider

Dead loads:
Tank self-weight (shell, base plate, roof if any).

Water weight:  (use 1000 kg/m³ for fresh water).

Live loads:
Maintenance live loads on platform/walkways (per code).

Hydrostatic loads:
Vertical (weight) and circumferential pressure on tank walls — handled by tank design, transmitted to support at tank footings or ring.

Wind loads:
Wind pressure on exposed tank and tower. Use code wind speed → pressure distribution. Consider drag on cylindrical tank and tower members; compute overturning moment.

Seismic loads:
Base shear applied to entire mass (tank + water + structure) using seismic coefficients from code (equivalent static or response spectrum). Consider impulsive and convective (sloshing) components for the liquid.

Sloshing / hydrodynamic effects:
For partially filled tanks, sloshing adds dynamic forces. Use appropriate tank-liquid interaction provisions in codes.

Temperature effects:
Thermal expansion constraints for long piping or large temperature swings.

Impact, surge, and pipe thrust:
Forces from filling/emptying, valves closing (water hammer mitigation needed).

Construction loads:
Erection phases and temporary bracing.

3) Load combinations & safety factors:

Apply the code’s required load combinations (dead + live + wind, dead + seismic + live, etc.).

Use appropriate partial safety factors for materials and loads as provided by your chosen design standard.

4) Global stability and geometry

Height-to-base ratio: keep tower as squat and wide as practical for stability.

Leg layout: vertical legs are preferable to slanted members that introduce eccentricity.

Bracing: provide diagonal cross-bracing (X or K bracing) in both orthogonal directions to resist lateral loads and prevent sway. Bracing should be continuous and tied into a rigid base.

Platform & ring beams: provide a rigid tank-support ring or grillage to distribute tank loads to legs evenly.

5) Member design checks

For each member (columns, bracings, beams):

Axial (compression/tension) — check axial capacity:  or . For compression consider buckling: slenderness . Use Euler/Empirical buckling formulas per code.

Combined bending + axial — check interaction (e.g.,  or code-specific interaction equations).

Shear & connections — shear, bolt shear, weld capacity. Check local plate shear where tank sits on support.

Deflection limits — serviceability limits for lateral drift and deflection under wind/seismic.

Fatigue — if cyclic loads significant (pumping, wind vortex shedding).

6) Foundation & anchorage

Base reactions: vertical loads, shear, overturning moment.

Design foundation: mass or spread footing sized with soil bearing pressure; or pile foundations if soil is weak.

Anchor bolts & base plate: design for tension (uplift), shear, and moment. Provide proper embedment, grout, and corrosion protection.

Uplift checks: under wind/seismic the foundation must resist uplift — include hold-down (anchor) design or increased weight of footing.

7) Tank support details

Tank support ring or grillage: a steel ring beam or support skirt that transfers load evenly to legs. Avoid point loads that cause local overstress.

Bearing/seat: allow for small rotation/settlement with flexible connection or neoprene pads if required.

@etconp

Continued ...

💫Bolted or welded connection: design gusset plates, stiffeners, and welds. Provide stiffener plates where legs meet tank ring.

8) Corrosion, durability, and maintenance

Material selection: suitable structural steel grade (S235, S275 etc. or per Ethiopian code). Tank liner or stainless if required.

Protective coatings: primer + paint system or galvanizing for exposed members. Consider sacrificial anodes or cathodic protection if aggressive environment.

Drainage & cleaning access: design manholes, drain points.

Inspection access: ladders, platforms, fall protection, safety cages. Plan for periodic inspection of welds, bolts, and paint.

9) Service piping & hydraulic considerations

Inlet/outlet piping: internal piping routing and anchor points so pipe thrusts do not load the tower unnecessarily.

Valves & air vents: overflow, venting, anti-surge measures.

Water hammer: include air chambers or surge protection to avoid sudden loads.

10) Practical design recommendations / good practices

Use vertical main legs rather than slanted legs if possible; slanted legs create bending eccentricities.

Provide full cross-bracing in both directions; bolt connections to gusset plates.

Make the foundation wider than the tower footprint (reduce overturning).

Keep center of gravity low — place platform and tank as low as practical.

Use a stiff tank support ring so tanks don’t create unbalanced loads on legs.

Design for both full and empty tank conditions (empty can change dynamic and wind behavior).

Avoid slender, long members without intermediate bracing (tie beams at one or more levels).

Provide redundancy — if one member fails, the structure shouldn’t collapse catastrophically.

11) Typical analysis workflow (step-by-step)

i. Determine tank weight (full & empty) and CG location.
ii. Compute static vertical reactions if tank supported by ring to N legs.
iii. Calculate wind and seismic lateral loads and moments about foundation.
iv. Model tower in frame analysis software (SAP2000, STAAD, ETABS, or static hand-checks for simple towers). Use 3D frame model including tank mass at top.
v. Extract member axial, shear, and moment forces for critical load combinations.
vi. Size columns & braces by axial, buckling, and interaction checks.
vii. Design connections and gusset plates.
viii. Design foundation for combined vertical, shear, and moment (eccentricity method or footing with overturning check).
ix. Check serviceability (deflections, vibration).
x. Prepare detailed drawings, erection sequence, and inspection plan.

12) Checks and special considerations

Eccentric loads from slanted legs or offset tank support.

Resonance / vortex shedding for tall slender towers — check for dynamic amplification (tall slender towers may need dampers or periodic cross-bracing spacing to break up long unbraced lengths).

Local plate buckling under concentrated loads (use stiffeners).

Redundant load paths (avoid single-bolt critical connections).

Safety: fall protection, signage, lightning protection if tower is tall.

13) Documentation & commissioning

Structural calculations, drawings, load assumptions, material specs, welding procedures, NDT requirements.

Erection procedure and temporary bracing plan.

Testing: hydrostatic test of tank, proof load test of structure if required.

Maintenance & inspection schedule.

@etconp

👉የኮንስትራክሽን ብቃት ማረጋገጫና ምዝገባ
መመሪያ 648/2013 መሠረት ስራ ተቋራጮች ባላቸው ደረጃ እስከ ምን ያህል ፕሮጀክት ዋጋ መጫረት ይችላሉ?

📜ከላይ ያለው ምስል ይመልከቱ🙏

@etconp

👋ሰላም ለዚህ ቻናል ቤተሰቦች

🏷በ ኦንላይን Quantity Surveying መመማር የምትፈልጉ በ @Philemona7 ፃፉልን ወይም በ 0925446661 ደውሉልን🙏

🎲ኮርሱ ሲያጠናቅቁ ሰርትፍኬት ይሰጦታል❗️

@etconp

👉 INTERCON Construction Chemicals 

● Concrete Admixtures
● Bonding Agents
● Waterproofings
● Wall Putty, Prime Coat
● Concrete Repair Mortar
● Floor hardener, Epoxy
● Grout, Self-level mortar
● Quartz paint, Contextra
● Tile Adhesive & Tile Joint Fillers 
● Geotextiles and other construction chemicals and materials

☎️ Tel: 0961955555

🔹 Address 1: Signal road, around
      Dinberwa Hospital

🔹 Addres 2: Wellosefer, Infront of
     Dani Plaza