Ethio Construction Engineering
32.3K subscribers
6.27K photos
359 videos
1.99K files
3.31K links
๐Ÿ”จ World Construction Engineering
Latest updates, tips, and tutorials on building, civil engineering, and construction in World.
Learn, build, and grow with us!

๐Ÿ“จ @Philemona7 Or @ETCONpBOT

For Ad:- https://telega.io/c/etconp
Download Telegram
๐Ÿ‘‰The temperature of the asphalt plant mix depends on the type of asphalt mix being produced and the specifications of the project.

๐Ÿ’ซGeneral guidelines are:

๐Ÿšง1. Hot Mix Asphalt (HMA):

Mixing temperature: 275โ€“325ยฐF (135โ€“165ยฐC)

Typically used for road construction.

๐Ÿšง2. Warm Mix Asphalt (WMA):

Mixing temperature: 200โ€“275ยฐF (95โ€“135ยฐC)

Preferred for environmentally friendly projects due to reduced emissions.

๐Ÿšง3. Cold Mix Asphalt:

No heating is involved, as it uses emulsified asphalt or cutback.

The exact temperature depends on factors like:

The type of binder (e.g., viscosity and grade).

Aggregate properties.

Weather and environmental conditions.

Plant specifications and operational standards.

Itโ€™s essential to follow the mix design or code requirements (e.g., AASHTO, ASTM, or local standards) for accurate temperature ranges.

@etconp
โค8๐Ÿ‘4
๐Ÿ‘‰แˆตแˆซ แˆแˆ‹แŒŠแ‹Žแ‰ฝ แ‰ แ‰ฐแˆˆแ‹ญแˆ แŠ แ‹ฒแˆต แˆแˆฉแ‰ƒแŠ• แˆตแˆซ แŠฅแŠ“แŒˆแŠ“แŠ›แˆˆแŠ• แŠจแˆšแˆ‰ แŠ แŒญแ‰ แˆญแ‰ฃแˆชแ‹Žแ‰ฝ แ‰ฐแŒ แŠ•แ‰€แ‰โ€ผ๏ธ

@etconp

https://t.me/ETCONpWORK/2714?single
๐Ÿ™3๐Ÿ‘2
๐Ÿ‘‰แ‹จแˆตแ‹Šแ‹ แ‰ฆแ‹ญแŠ• แ‹ญแ‰€แŠ“แ‰€แŠ“แˆ แ‹จแ‰ฐแ‰ฃแˆˆแ‹ แ‹จ17 แ‰ขแˆŠแ‹จแŠ• แ‹ถแˆ‹แˆญ แŒแ‹™แ แ•แˆฎแŒ€แŠญแ‰ต

๐Ÿšงแˆ˜แˆญแŠจแ‰ฆแ‰ฝ แ‰ แˆตแ‹Šแ‹ แ‰ฆแ‹ญ แ‰ แŠฉแˆ แˆˆแˆ›แˆˆแ แ‹จแˆšแ‹ˆแˆตแ‹ตแ‰ฃแ‰ธแ‹แŠ• แŒŠแ‹œ แŠฅแˆตแŠจ 15 แ‰€แŠ“แ‰ต แˆ›แˆณแŒ แˆญ แ‹ญแ‰ฝแˆ‹แˆ แ‰ฐแ‰ฅแˆแˆ แ‰ แŠ แŒˆแˆแŒแˆŽแ‰ฑ แ‹จแŒแ‰ฅแŒนแŠ• แˆตแ‹Šแ‹ แ‰ฆแ‹ญ แ‹ญแ‰€แŠ“แ‰€แŠ“แˆ แ‹จแ‰ฐแ‰ฃแˆˆ แŒแ‹™แ แ‹จแˆ˜แŠ•แŒˆแ‹ต แ•แˆฎแŒ€แŠญแ‰ต แ‹ˆแ‹ฐ แ‰ฐแŒแ‰ฃแˆญ แˆˆแˆ˜แŒแ‰ฃแ‰ต แ‹จแŠฅแ‰…แ‹ต แˆตแˆซแ‹ แ‰ แˆ˜แŒ แŠ“แ‰€แ‰… แˆ‹แ‹ญ แŠฅแŠ•แ‹ฐแˆšแŒˆแŠ แ‰ฐแˆฐแˆแ‰ทแˆแข

๐Ÿท17 แ‰ขแˆŠแ‹จแŠ• แ‹ถแˆ‹แˆญ แ‹ซแ‹ˆแŒฃแˆ แ‹จแ‰ฐแ‰ฃแˆˆแ‹ แˆœแŒ‹ แ•แˆฎแŒ€แŠญแ‰ต แŠจ1198 แŠชแˆŽแˆœแ‰ตแˆญ แ‰ แˆ‹แ‹ญ แŠฅแˆญแ‹แˆ›แŠ” แŠฅแŠ•แ‹ฐแˆšแŠ–แˆจแ‹ แ‰ฐแАแŒแˆฎแˆˆแ‰ณแˆแข

โบแˆแ‹•แˆซแ‰ฅ แŠฅแˆตแ‹ซ แŠฅแŠ“ แŠ แ‹แˆฎแ“แŠ• แ‰ แˆ›แŒˆแŠ“แŠ˜แ‰ต แ‹ซแˆแ‰ฐแ‰†แˆซแˆจแŒ  แ‹จแˆแˆญแ‰ต แ‹แ‹แ‹แˆญ แ‹ซแˆณแˆแŒฃแˆ แ‹จแ‰ฐแ‰ฃแˆˆ แˆฒแˆ†แŠ•แค แˆแˆˆแ‰ฑ แŠ แˆ…แŒ‰แˆฎแ‰ฝ แˆแˆญแ‰ต แˆˆแˆ˜แˆˆแ‹‹แ‹ˆแŒฅ แ‰ แˆตแ‹Šแ‹ แ‰ฆแ‹ญ แˆ‹แ‹ญ แ‹ซแˆ‹แ‰ธแ‹แŠ• แŒฅแŒˆแŠแАแ‰ต แŠฅแŠ•แ‹ฐแˆšแ‰€แŠ•แˆต แ‰ฐแˆตแ‹ แ‰ฐแŒฅแˆŽแ‰ แ‰ณแˆ แ‹จแˆ˜แŠ•แŒˆแ‹ต แŒแŠ•แ‰ฃแ‰ณแ‹ แˆ˜แАแˆปแ‹แŠ• แŠจแ‰ฑแˆญแŠญ แˆฐแˆœแŠ“แ‹Šแ‹ แ‹ตแŠ•แ‰ แˆญ แŠ แ‹ตแˆญแŒŽ แŠฅแˆตแŠจ แ‹ฐแ‰กแ‰ฃแ‹Š แ‹จแ‹แˆญแˆต แ‰ฃแˆ…แˆจ แˆฐแˆ‹แŒค แ‹ตแˆจแˆต แ‹ญแ‹˜แˆจแŒ‹แˆแข

โบแ‹จแˆ˜แŠ•แŒˆแ‹ต แฃ แ‹จแ‰ฃแ‰กแˆญ แˆ€แ‹ฒแ‹ต แฃ แ‹จแ‹ˆแ‹ฐแ‰ฅ แŠฅแŠ“ แ‹จแŠจแ‰ฐแˆ› แˆ˜แŠ•แŒˆแ‹ถแ‰ฝแŠ• แŠจแˆ€แŒˆแˆญ แŠ แ‰‹แˆซแŒญ แˆ˜แŠ•แŒˆแ‹ถแ‰ฝ แŒ‹แˆญ แˆ›แŒˆแŠ“แŠ˜แ‰ตแŠ• แ‹ซแ‰€แˆแ‹ แ‹ญแˆ… แˆœแŒ‹ แ•แˆฎแŒ€แŠญแ‰ต แ‰ แŠฅแˆตแ‹ซ แŠฅแŠ“ แ‰ แŠ แ‹แˆฎแ“ แˆ˜แŠซแŠจแˆ แ‹ซแˆˆแ‹แŠ• แ‹จแŒ‰แ‹ž แŒŠแ‹œ แˆˆแˆ˜แ‰€แАแˆต แ‹ซแˆˆแˆ˜ แАแ‹แกแก

โบแ‰ แˆแˆˆแ‰ฑ แŠ แˆ…แŒ‰แˆซแ‰ต แˆ˜แŠซแŠจแˆ แˆˆแˆšแŒˆแŠแ‹ แŠขแŠฎแŠ–แˆšแ‹ซแ‹Š แŒแŠ•แŠ™แАแ‰ต แ‹ˆแˆณแŠ แ‹จแŠ•แŒแ‹ต แˆ˜แˆตแˆ˜แˆญ แˆˆแˆ†แАแ‹ แ‹จแŒแ‰ฅแŒน แˆตแ‹Šแ‹ แ‰ฆแ‹ญ แ‰ฐแŽแŠซแŠซแˆช แ‹จแˆ˜แˆ†แŠ• แŠฅแ‹ตแˆ‰แˆ แŠจแแ‰ฐแŠ› แˆ˜แˆ†แŠ‘ แ‰ฐแˆ˜แˆ‹แŠญแ‰ทแˆ แข

แ‰ฑแˆญแŠญ แˆ‹แ‹ญ แ‹จแŠ•แŒแ‹ต แŠฎแˆชแ‹ฐแˆญ แŠจแ‹˜แˆจแŒ‹ แ‰ แŠ‹แˆ‹ แ‹จแŠขแˆซแ‰…แŠ• แ‹“แˆˆแˆ แŠ แ‰€แ แ‰ฐแˆฐแˆšแАแ‰ต แŠฅแŠ•แ‹ฒแˆแˆ แ‹จแˆ€แŒˆแˆญ แ‹แˆตแŒฅ แŠขแŠฎแŠ–แˆšแ‹‹แŠ• แŠฅแŠ“ แˆ˜แˆ แˆจแ‰ฐ แˆแˆ›แ‰ตแŠ• แ‹ซแŒ แŠ“แŠญแˆซแˆ แ‰ฐแ‰ฅแˆŽ แ‹ญแŒ แ‰ แ‰ƒแˆแข

แ‹จแŠขแˆซแ‰… แŒ แ‰…แˆ‹แ‹ญ แˆšแŠ’แˆตแ‰ตแˆญ แˆ˜แˆแˆ˜แ‹ต แˆบแ‹“ แŠ แˆแˆฑแ‹ณแŠ’ แ•แˆฎแŒ€แŠญแ‰ฑ แ‰ แ‹˜แˆ‹แ‰‚แАแ‰ต แŠจแАแ‹ณแŒ… แŒฅแŒˆแŠแАแ‰ต แ‹จแ‰ฐแˆ‹แ‰€แ‰€ แŠขแŠฎแŠ–แˆšแŠ• แˆˆแˆ˜แŒˆแŠ•แ‰ฃแ‰ต แ‹จแˆ›แ‹•แ‹˜แŠ• แ‹ตแŠ•แŒ‹แ‹ญ แАแ‹ แ‹ซแˆ‰ แˆฒแˆ†แŠ•แค แŠขแˆซแ‰…แŠ•แŠ“ แŠ แŠซแ‰ฃแ‰ขแ‹แŠ• แ‹จแˆšแŒ แ‰…แˆ แˆˆแ‰€แŒ แŠ“แ‹Š แ‰ตแˆตแˆตแˆญ แŠฅแŠ“ แˆˆแŠขแŠฎแŠ–แˆš แ‹แˆ…แ‹ฐแ‰ต แ‹จแˆšแŠ–แˆจแ‹แˆ แ‹ตแˆญแˆป แŠจแแ‰ฐแŠ› แˆตแˆˆแˆ˜แˆ†แŠ‘ แŠ แŠ•แˆตแ‰ฐแ‹‹แˆ::

แ‹จแŠขแˆซแ‰ โ€œแ‹จแŒแˆซแŠ•แ‹ต แŽแ‹ แ–แˆญแ‰ตโ€ แ‰ แ‹šแˆ… แˆ˜แŠ•แŒˆแ‹ต แ‹จแˆšแ‰ฐแˆ‹แˆˆแ‰ แˆแˆญแ‰ถแ‰ฝแŠ• แŒญแАแ‹ แ‹จแˆšแˆ˜แŒก แˆ˜แˆญแŠจแ‰ฆแ‰ฝแŠ• แˆˆแˆ›แˆตแ‰ฐแŠ“แŒˆแ‹ต แˆƒแˆ‹แŠแАแ‰ต แ‰ฐแŒฅแˆŽแ‰ แ‰ณแˆแกแก

แŠฅแŠ•แ‹ฐ แˆ€แŒˆแˆชแ‰ฑ แ‹จแ‰ตแˆซแŠ•แˆตแ–แˆญแ‰ต แˆšแŠ’แˆตแ‰ตแˆญ แˆ˜แˆจแŒƒ แŠจแˆ†แА แ‹ญแˆ… แ‹ˆแ‹ฐแ‰ฅ แŠฅแˆตแŠจ19.5 แˆœแ‰ตแˆญ แŒฅแˆแ‰€แ‰ต แ‹ซแˆ‹แ‰ธแ‹ แ‰ตแˆ‹แˆแ‰… แ‹จแŠ•แŒแ‹ต แˆ˜แˆญแŠจแ‰ฆแ‰ฝแŠ• แˆ›แˆตแ‰ฐแŠ“แŒˆแ‹ต แ‹ญแ‰ฝแˆ‹แˆแข

แŠจแŒแ‰ฅแŒน แˆตแ‹Šแ‹ แŠซแŠ“แˆ แŒ‹แˆญ แˆฒแАแƒแ€แˆญแˆ แ‰ แŒ‰แ‹ž แŒŠแ‹œ แŠจ12 แŠฅแˆตแŠจ 15 แ‰€แŠ“แ‰ต แˆ˜แ‰†แŒ แ‰ฅ แŠฅแŠ•แ‹ฐแˆšแ‰ฝแˆแˆ แ‰ฐแˆฐแˆแ‰ทแˆแกแก

แˆšแŠ’แˆตแ‰ตแˆฉ แˆซแ‹›แ‰… แˆ™แˆ‚แ‰ขแˆต แŠ แˆแˆณแ‹ณแ‹Š โ€œแ‰ แ‹šแˆ… แ•แˆฎแŒ€แŠญแ‰ต แŠขแˆซแ‰… แŠฅแŠ“ แ‰ฑแˆญแŠญ แ‹จแŒ‚แŠฆแ–แˆˆแ‰ฒแŠซแ‹Š แŒ แ‰€แˆœแ‰ณ แ‹ซแŒˆแŠ›แˆ‰แค แАแŒˆแˆญ แŒแŠ• แˆ™แˆ‰ แ‰ แˆ™แˆ‰ แŠจแ–แˆˆแ‰ฒแŠซ แ‹จแŒธแ‹ณ แŠขแŠฎแŠ–แˆš แˆ‹แ‹ญ แ‹ซแ‰ฐแŠฎแˆจ แ‰ฅแ‰ป แ‹ญแˆ†แŠ“แˆโ€ แ‰ฅแˆˆแ‹‹แˆแกแก

แ‰ แˆถแˆตแ‰ต แŠ แˆ˜แ‰ต แˆˆแˆ›แŒ แŠ“แ‰€แ‰… แŠฅแ‰…แ‹ต แ‹จแ‰ฐแ‹ซแ‹˜แˆˆแ‰ต แˆœแŒ‹ แ•แˆฎแŒ€แŠญแ‰ต แ‰ แ‰ แˆญแŠซแ‰ณ แ‰ฐแ…แ‹•แŠ– แˆแŒฃแˆช แˆ€แŒˆแˆซแ‰ต แ‹ตแŒ‹แ แ‹ซแŒˆแŠ˜ แˆฒแˆ†แŠ•แค แŠ แˆจแ‰ฅ แŠคแˆšแˆฌแ‰ตแˆต แŠฅแŠ“ แ‹จแŠณแ‰ณแˆญ แˆ˜แŠ•แŒแˆตแ‰ณแ‰ต แ‰ฃแˆˆแˆแ‹ แŠญแˆจแˆแ‰ต แ‰ แ•แˆฎแŒ€แŠญแ‰ฑ แ‹จแŒ‹แˆซ แˆแˆ›แ‰ต แ‹™แˆญแ‹ซ แˆตแˆแˆแАแ‰ต แ‰ฐแˆแˆซแˆญแˆ˜แ‹‹แˆแข

Via Alain

@etconp
๐Ÿ‘20๐Ÿ”ฅ1
Modernism in Africa.pdf
63.7 MB
๐Ÿ‘‰แŠ แ‹ฒแˆต แ‹จแˆ˜แŒฝแˆ€แ แŒฅแ‰†แˆ›

๐Ÿ’ซModernism in Africa.

โญ๏ธแ‰ แ‹˜แŒ แŠ แŠ แแˆชแŠซ แŠ แŒˆแˆซแ‰ต แ‹ซแˆ‰แ‰ตแŠ• แ‹จแ‹˜แˆ˜แŠ“แ‹Šแ‹แŠ• แ‹˜แ‹ญแ‰ค แˆ…แŠ•แŒป แŠ•แ‹ตแ แ‹จแ‰ฐแ‰ฐแАแ‰ฐแАแ‰ แ‰ต แŠฅแŒ…แŒ แŒ แ‰ƒแˆš แˆ˜แŒฝแˆ€แ แ‰ แ‰ แ‹ญแА แˆ˜แˆจแ‰ฅ แ‰ แАแŒป แ‹จแ‰ฐแˆˆแ‰€แ‰€ แˆฒแˆ†แŠ•  แˆ˜แŒฝแˆ€แ‰แŠ• แŠจแˆ‹แ‹ญ แ‰ แ‰ฐแ‹ซแ‹ซแ‹˜แ‹ แ’แ‹ฒแŠคแ  แŠ แ‹แˆญแ‹ถ แˆ›แŠ•แ‰ แ‰ฅ แ‹ญแ‰ปแˆ‹แˆแกแก

@etconp
๐Ÿ”ฅ9๐Ÿ‘8๐Ÿ™2
#ADVERTISEMENTS

๐Ÿ‘‰แ‹จ แˆ˜แŠ•แŒˆแ‹ต แŒแŠ•แ‰ฃแ‰ณ แ‹ฒแ‹›แ‹ญแŠ• แˆตแˆซ แˆ›แˆฐแˆซแ‰ต แ‹ญแˆแˆแŒ‹แˆ‰?

๐Ÿทแ‰  แˆ˜แŠ•แŒˆแ‹ต แˆตแˆซ แˆ‹แ‹ญ แ‹จแŠ แˆแˆญ แˆ˜แŒ แŠ• แŠฅแŠ“ แ‹‹แŒ‹ แˆตแˆŒแ‰ตแฃแ‹จ แŠ แˆตแ‹แˆแ‰ต แˆแŠ•แŒฃแ แˆตแˆŒแ‰ตแฃแˆ™แˆ‰ แ‹จ แˆตแ‰ตแˆซแŠญแ‰ธแˆซแˆ แ‹ตแˆฎแ‹ŠแŠ•แŒ แˆตแˆซ แ‰ แŽแŒฅแАแ‰ต แŠฅแŠ“ แ‰  แŒฅแˆซแ‰ต แˆฐแˆญแ‰ฐแŠ• แŠฅแŠ“แˆตแˆจแŠญแ‰ฃแˆˆแŠ•แข

๐ŸšงแŠฅแŠ•แ‹ฒแˆแˆ Civil 3D แ‰ฒแ‰ถแˆญแ‹ซแˆ แ‰ชแ‹ตแ‹ฎ แŠจแА แˆ™แˆ‰ แˆ›แ‰ฐแˆชแ‹ซแˆ
แ‹จ Girder Birdge Working Drawing แŠจแА 3D modelแŠ“ แˆ™แˆ‰ แˆ›แ‰ฐแˆชแ‹ซแˆ แ‰ชแ‹ตแ‹ฎ แ‰ แ‰ฐแŒจแˆ›แˆช แˆ›แАแŠ›แ‹แˆ แ‹จแˆ˜แŠ•แŒˆแ‹ต แˆตแˆซ แ‹แ‹ญแˆŽแ‰ฝ แŠฅแŠ“ แ‰ดแˆแ•แˆŒแ‰ถแ‰ฝ แŠ แˆ‰แŠ•แข

๐Ÿ’ซแŠจแ‰ณแ‰ฝ แ‰ฃแˆ‰แ‰ต แŠฃแˆ›แˆซแŒฎแ‰ฝ แ‹ญแŒŽแ‰ฅแŠ™แŠ•

YouTube: http://www.youtube.com/@musfide

แ‹ตแˆ…แˆจ แŒˆแ…:- www.musfide.com

แ‰ดแˆŒแŒแˆซแˆ แŒˆแ…:- https://t.me/musafide

แˆŠแŠ•แŠญแ‹ฐแŠ•:- https://www.linkedin.com/in/musfide

แ‹ˆแ‹ญแˆ แ‰  +251905666664 แŠจแ‹ฐแ‹ˆแˆ‰ แ‹ซแŒˆแŠ™แŠ“แˆ๐Ÿ™
๐Ÿ‘10
๐Ÿ‘‰Curing Time According to ACI ๐Ÿ•’๐Ÿ—๏ธ

โญ๏ธThe American Concrete Institute (ACI) provides specific guidelines for curing to ensure concrete achieves its designed strength and durability:

๐Ÿ’ซ1. Beam ๐Ÿชต

Initial Curing: 24-48 hours ๐ŸŒง๏ธ๐Ÿ”’

Final Curing: Minimum 7 days for normal cement  or 3 days for high-early-strength cement.

Recommended as per ACI 308R-16.

๐Ÿ’ซ2. Column ๐Ÿ›๏ธ

Initial Curing: 24-48 hours ๐ŸŒง๏ธ

Final Curing: Same as beams, 7 days minimum for normal cement or 3 days for high-early-strength cement.

๐Ÿ’ซ3. Slab ๐Ÿ 

Initial Curing: 24-48 hours ๐ŸŒง๏ธ๐Ÿ”’ (Cover with plastic sheets, wet burlap, or curing blankets).

Final Curing: Minimum 7 days (ponding or sprinkling for slabs is highly recommended).

๐Ÿ’ก According to ACI 308-92, the curing period can be adjusted based on factors like cement type, ambient conditions, and strength requirements. Proper curing is vital for reducing shrinkage, cracking, and ensuring durability!


@etconp
๐Ÿ‘15๐Ÿ‘8โค3
๐Ÿ‘‰Borrow material and Selected material

๐ŸšงIn construction, borrow material is a naturally occurring material used to create fill and structural elements, while selected material is a material chosen to meet specific project requirements:

๐Ÿ’ซBorrow material

๐ŸทA naturally occurring material that's excavated from a borrow pit and used to create fill and structural elements like embankments.

โบBorrow material is selected to meet the project's grading, stability, and load-bearing capacity requirements.

๐Ÿ’ซSelected material

๐ŸทA material chosen to meet specific project requirements. When selecting construction materials, factors to consider include strength, durability, cost, availability, and climate.

โญ๏ธWhen selecting a borrow area, it's important to consider the quantity and quality of the fill, as well as the type of equipment that will be used.

@etconp
๐Ÿ‘14
๐Ÿ‘‰Bleeding & Segregation in Concrete

๐ŸšงBleeding

โžก๏ธBleeding is a form of segregation in which water present in the concrete mix is pushed upwards due to the settlement of cement and aggregate.

โžก๏ธThe specific gravity of water is low, due to this water tends to move upwards.

โžก๏ธBleeding ordinarily occurs in the wet mix of concrete.

โžก๏ธThe Prime factor for bleeding in concrete is the high dosage of Water cement ratio.

โžก๏ธHigher water-cement ratio weakens concrete and leads to excessive bleeding.

โžก๏ธThe bleeding in concrete is not harmful if the rate of evaporation of water is equal to the rate of bleeding.

โžก๏ธNormal bleeding is quite good, and it enhances the workability of concrete.

โžก๏ธWhen the concrete is fully plastic, bleeding may not cause much harm. However, concrete is still in the plastic stage later it is subsidized and compacted.

๐ŸšงSegregation

โ–ถ๏ธSegregation is the โ€œSeparation of constituent materials in concrete"

โžก๏ธIn concrete technology segregation is of three types

โบ1. Separation of Coarse aggregate from the concrete mixture.

โบ2. Separation of Cement pastes from the concrete during its plastic stage.

โบ3. Separation of water from the concrete mix (Bleeding in concrete)

===================
Invite your friends to this channel
====================

@etconp
๐Ÿ‘17โค2
๐Ÿ‘‰แ‰ แŒแŠ•แ‰ฃแ‰ณ แˆตแˆซ แˆ‹แ‹ญ แˆˆแ‰ฐแˆฐแˆ›แˆฉ แ‰ฐแ‰‹แˆซแŒฎแ‰ฝแŠ“ แŠ แˆ›แŠซแˆชแ‹Žแ‰ฝ แ‹จแ‰ฐแ‹˜แŒ‹แŒ€แ‹ แ‹จแ‹“แ‰…แˆ แŒแŠ•แ‰ฃแ‰ณ แˆตแˆแŒ แŠ“ แŠฅแ‹จแ‰ฐแˆฐแŒ  แАแ‹

แ‰ แŠ แ‹ฒแˆต แŠ แ‰ แ‰ฃ แ‹ฒแ‹›แ‹ญแŠ•แŠ“ แŒแŠ•แ‰ฃแ‰ณ แˆตแˆซแ‹Žแ‰ฝ แ‰ขแˆฎ แ‹จแ‰ฐแ‹˜แŒ‹แŒ€แ‹แŠ“ แ‰ตแŠฉแˆจแ‰ฑแŠ• Construction Material Management แŠฅแŠ“ Construction Human Resource Management แˆ‹แ‹ญ แ‹ซแ‹ฐแˆจแŒˆแ‹ แ‹จแ‹“แ‰…แˆ แŒแŠ•แ‰ฃแ‰ณ แˆตแˆแŒ แŠ“ แŠฅแ‹จแ‰ฐแˆฐแŒ  แ‹ญแŒˆแŠ›แˆแกแก

แ‰ แ‰ขแˆฎแ‹ แ‰ แ‰ฐแŠจแ‰ณแ‰ณแ‹ญแАแ‰ต แŠฅแ‹จแ‰ฐแˆฐแŒก แŠจแˆšแŒˆแŠ™แŠ“ แ‹จแŠฎแŠ•แˆตแ‰ตแˆซแŠญแˆฝแŠ• แŠขแŠ•แ‹ฑแˆตแ‰ตแˆชแ‹แŠ• แ‹“แ‰…แˆ แŠจแˆšแ‹ซแŒŽแˆˆแ‰ฅแ‰ฑ แˆตแˆแŒ แŠ“แ‹Žแ‰ฝ แ‹แˆตแŒฅ แŠ แŠ•แ‹ฑ แ‰ แˆ†แАแ‹ แ‰ แ‹šแˆ€ แˆตแˆแŒ แŠ“ แ‰ แŠ แ‹ฒแˆต แŠ แ‰ แ‰ฃ แŠจแ‰ฐแˆ› แ‹จแˆšแŒˆแŠ™ 250 แˆตแˆซ แ‰ฐแ‰‹แˆซแŒฎแ‰ฝ แŠฅแŠ“ แŠ แˆ›แŠซแˆชแ‹Žแ‰ฝ  แŠฅแ‹จแ‰ฐแˆณแ‰ฐแ‰ แ‹ญแŒˆแŠ›แˆ‰แกแก

แ‰ แ‰€แŒฃแ‹ญแˆ แ‰ แˆแˆˆแ‰ฐแŠ› แ‹™แˆญ Construction Claim and Dispute Resolution แ‰ แˆšแˆ แ‹จแˆตแˆแŒ แŠ“ แˆญแ‹•แˆต แˆ‹แ‹ญ แˆตแˆแŒ แŠ“แ‹ แŠ แŠ•แ‹ฐแˆšแ‰€แŒฅแˆ แŠจแ‰ขแˆฎแ‹ แ‹จแ‹“แ‰…แˆ แŒแŠ•แ‰ฃแ‰ณ แ‹ณแ‹ญแˆฌแŠญแ‰ถแˆฌแ‰ต แ‹ซแŒˆแŠ˜แАแ‹ แˆ˜แˆจแŒƒ แ‹ซแˆณแ‹ซแˆแข

แ‰ขแˆฎแ‹ แ‰ แˆญแŠซแ‰ณ แŒแŠ•แ‰ฃแ‹Žแ‰ฝแŠ• แ‰ แŒฅแˆซแ‰ต แ‰ แˆ›แŠจแŠ“แ‹ˆแŠ• แˆˆแŠ แŒˆแˆแŒแˆŽแ‰ต แŠฅแ‹ซแ‹‹แˆˆ แŠจแˆ˜แˆ†แŠ‘ แŒŽแŠ•แˆˆแŒŽแŠ• แ‹จแŠขแŠ•แ‹ฑแˆตแ‰ตแˆชแ‹แŠ• แ‰ฐแ‹‹แŠ•แ‹ซแŠ• แ‹“แ‰…แˆ แ‹จแˆšแ‹ซแŒŽแˆˆแ‰ฅแ‰ฑ แ‰ฐแŠจแ‰ณแ‰ณแ‹ญ แˆตแˆแŒ แŠ“แ‹Žแ‰ฝแŠ• แ‰ แˆ˜แˆตแŒ แ‰ต แ‹จแŠจแ‰ฐแˆ›แ‹ แŠฎแŠ•แˆตแ‰ตแˆซแŠญแˆฝแŠ• แ‹•แ‹ตแŒˆแ‰ต แˆ‹แ‹ญ แ‹จแˆ‹แ‰€ แ‹จแ‹ตแˆญแˆป แŠฅแ‹ซแ‰ แˆจแŠจแ‰ฐ แ‹ญแŒˆแŠ›แˆแข

แ‹จแŠ แ‹ฒแˆต แŠ แ‰ แ‰ฃ แ‹ฒแ‹›แ‹ญแŠ•แŠ“ แŒแŠ•แ‰ฃแ‰ณ แˆตแˆซแ‹Žแ‰ฝ แ‰ขแˆฎ แŠฎแˆ™แŠ’แŠฌแˆฝแŠ• แŒ‰แ‹ณแ‹ฎแ‰ฝ แ‹ณแ‹ญแˆฌแŠญแ‰ถแˆฌแ‰ต แ‰ณแˆ…แˆณแˆต 2/2017 แ‹“.แˆ

@etconp
๐Ÿ‘12โค3
Intercon Construction Chemicals 
    
๐Ÿ‘‰ Authorized agent of MC (Conmix), Weber and SIMENTEK

โ— Concrete Admixtures
โ— Bonding Agents
โ— Waterproofings
โ— Concrete Repair, Grout   
โ— Tile Adhesive & Tile Joint Fillers 
โ— Wall Putty, Prime Coat, Rush Coat
โ— Quartz, Contextra
โ— Specialized paints (Thermal and Insulation Paints, Street and Playground Paints)
โ— Floor hardener, Epoxy              
โ— Geotextiles, Geo-membranes and other construction chemicals and materials

Tel: 0961955555 or 0961955559
Address: Signal, around signal mall
๐Ÿ‘3โค1
แ‰ณแˆแˆซแ‰ต  แ•แˆŒแ‰ต แŠฅแŠ“ แŒ„แ‰ฆแˆแ‰ต แŠ แ‰…แˆซแ‰ข

๐Ÿ‘‰แŠจ แŠ แ‰ฃแ‹ญ แŒแ‹ตแ‰ฅ แŠฅแˆตแŠจ แŠฎแˆชแ‹ฐแˆญ แˆแˆ›แ‰ต

แŠจแŒแˆˆแˆฐแ‰ฅ แ‰คแ‰ถแ‰ฝ แŠฅแˆตแŠจ แ‰ฐแ‰‹แˆ›แ‰ต แŠฅแŠ“

แˆ˜แŒ‹แ‹˜แŠ–แ‰ฝ แ‰ แˆแˆ‰แˆ แ‹จแŠขแ‰ตแ‹ฎแŒฝแ‹ซ แŠญแแˆ

แŠ แˆปแˆซแ‰ฝแŠ•แŠ• แŠ แˆณแˆญแˆแŠ“แˆ

๐Ÿ”ฐแˆแŠ• แ‹ญแˆแˆแŒ‹แˆ‰?

โœ‚๏ธแˆ‹แˆœแˆซ แˆ˜แ‰แˆจแŒซ รท แˆ›แŒ แŠแ‹ซ แŠฅแŠ“ แˆ˜แ‰ฅแˆป แˆ›แˆฝแŠ–แ‰ฝ แŠ แˆ‰แŠ•

๐Ÿ”—แŒแˆฎ (แ‰ถแŠ•แ‹ฒแŠ–) แŒฅแˆญแˆต แˆ›แˆตแ‰ แŒ€แ‰ต แ‹ˆแ‹ญแŠ•แˆ แˆ›แˆณแŒ แ แŠซแˆฐแ‰ก แˆˆแˆฑแˆ แˆ›แˆฝแŠ‘ แ‰ แŒƒแ‰ฝแŠ• แАแ‹‰

๐Ÿ“แˆ›แŠ•แŠ›แ‹‰แŠ•แˆ แ‹จแˆžแ‹ฐแŠแŠญ แˆตแˆซแ‹Žแ‰ฝแŠ• แ‹จแˆšแˆฐแˆฉ แ‰ฅแ‰ แ‰ฃแˆˆแˆ™แ‹ซแ‹Žแ‰ฝแˆ แŠ แˆ‰แŠ•

โ˜Ž๏ธแ‹ญแ‹ฐแ‹‰แˆ‰แˆแŠ• แ‹ซแˆ›แŠญแˆฉแŠ•

๐Ÿ“แŠขแ‰ตแ‹ฎแŒตแ‹ซ แ‹‰แˆตแŒฅ แ‹จแ‰ตแˆ แŠฅแŠ•แˆแŠญแˆŽแ‰ณแˆˆแŠ•

แŠ แ‹ตแˆซแˆปแ‰ฝแŠ•แฆ
                    แ‰.1 แˆ˜แˆญแŠซแ‰ถ
                    แ‰.2 แ‰ฐแŠญแˆˆแˆ€แ‹ญแˆ›แŠ–แ‰ต
                     แ‰.3 แŠ แ‹จแˆญ แŒคแŠ“

0904040477
0911016833
๐Ÿ‘‰แˆตแˆˆ STAIRS แ‰ตแŠ•แˆฝ แŒ แ‰ƒแˆš แˆƒแˆณแ‰ฅ แŠฅแŠ•แˆ›แˆ›แˆญ ๐Ÿ‘‡

๐ŸšงCalculations for the construction of stairs, ramps and guards are set out in various national building regulations.

๐Ÿ’ซThe guidelines here are based on German standards.

โ–ถ๏ธDwellings with no more than two flats must have an effective stair width of at least 0.80 m and 17/29 rise-to-tread ratio. Stairs which are not strictly covered by building regulations may be as little as 0.50m wide and have a 21/21 ratio.

โบStairs governed by building regulations must have a width of 1.00m and a ratio of 17/28.

โบIn high rise flats they must be 1.25 m wide

โบThe length of stair runs from 23 steps up to 18 steps --> @ Landing length = n times the length of stride + 1 depth of step (e.g. with a rise-to-tread ratio of 17/29 = 1 x 63 + 29 = 92 cm or 2 x 63 + 29 = 1.55 m).

โบDoors opening into the stairwell must not restrict the effective width.

โ–ถ๏ธThe time required for complete evacuation must be calculated for stair widths in public buildings or theatres. Such staircases or front entrance steps are climbed slowly, so they can have a more gradual ascent.

โ–ถ๏ธA staircase at a side entrance or emergency stairs should make a rapid descent easy.

โ–ถ๏ธThe experiences one has of ascending and descending stairs varies greatly with the stair design, for example there is a significant difference between an interior domestic design and a grand flight of entrance steps.

โบClimbing stairs takes on average seven times as much energy as walking on the flat.

โบFrom the physiological point of view, the best use of 'climbing effort' is with an angle of incline of 30ยฐ and a ratio of rise of:  rise of step/going of step; r/g= 17/29.

โ–ถ๏ธThe angle of rise is determined by the length of an adult's stride (about 61-64cm). To arrive at the optimum rise, which takes the least energy, the following formula can be applied: 2r+ g= 63cm (1 stride)

โ–ถ๏ธIn the dimensioning and design of flights of stairs, the function and purpose of the staircase is of primary importance, taking in the factors mentioned above.

โ–ถ๏ธNot only is the gaining of height important, but also the way that the height is gained. For front door steps in frequent use, low steps of 16 x 30cm are preferable.

โนHowever, stairs in a workplace, or emergency stairs, should enable height to be gained rapidly.

โบEvery main staircase must be set in its own continuous stairwell, which together with its access routes and exit to the open air, should be designed and arranged so as to ensure its safe use as an emergency exit. The width of the exit should be  greater than or equal tothe width of the staircase.

@etconp
๐Ÿ‘18โค2
๐Ÿ‘‰แŠฅแˆตแ‰ฒ แŠฃแˆแŠ• แ‹ฐแˆž แˆตแˆˆ lap length , Development length,Anchorage length แ‰ตแŠ•แˆฝ แŠฅแŠ•แŠ•แŒˆแˆซแ‰นแข

๐Ÿท1. แˆ‹แ• แˆŒแŠ•แŒแ‹ (lap length) - แ‰ฐแˆแˆ‹แŒŠ แ‹จแ‰ฅแˆจแ‰ต (แŒแˆฎ) แˆญแ‹แˆ˜แ‰ต
แ‹แŒฅแˆจแ‰ตแŠ• (stresses) แŠจแŠ แŠ•แ‹ต แ‰ฅแˆจแ‰ต แ‹ˆแ‹ฐแˆŒแˆ‹ แ‹จแˆšแ‰ฐแˆ‹แˆˆแแ‰ แ‰ต แАแ‹‰

โบThe lap length varies from member to member. Lap length for tension members = 40d

โบLap length for compression members = 50d Where, d = Diameter of bars.

๐Ÿท2. แ‹ฐแ‰จแˆŽแ•แˆ˜แŠ•แ‰ต แˆŒแŠ•แŒแ‹ (Development length) -แ‰ฐแˆแˆ‹แŒŠ
แ‹จแ‰ฅแˆจแ‰ต แˆญแ‹แˆ˜แ‰ต แ‹แŒฅแˆจแ‰ตแŠ• (stresses) แŠจแ‰ฅแˆจแ‰ฑ แ‹ˆแ‹ฐ แŠฎแŠ•แŠญแˆชแ‰ฑ แ‹จแˆšแ‰ฐแˆ‹แˆˆแแ‰ แ‰ต แАแ‹แข

๐Ÿท3. แŠ แŠ•แŠฎแˆฌแŒ… แˆŒแŠ•แŒแ‹ (Anchorage length) - แ‹ญแˆ… แˆญแ‹แˆ˜แ‰ต แŠ แ‹ญแАแ‰ต แ‰ แ‰‚ แ‹จแˆ†แА แ‹ฐแ‰จแˆŽแ•แˆ˜แŠ•แ‰ต แˆŒแŠ•แŒแ‹ (development
length ) แ‰ แˆŒแˆˆแ‰ฃแ‰ธแ‹ แ‰  Support / fixed ends แˆ‹แ‹ญ provide แ‹จแˆแŠ“แˆจแŒˆแ‹ แˆญแ‹แˆ˜แ‰ต แАแ‹แข

@etconp
๐Ÿ‘14โค10๐Ÿ‘Œ1
#ADVERTISEMENT

๐Ÿ’ซSpecialized Retrofitting (Jacketing) Services for:

โœ… Columns โ€“ Enhance load-carrying capacity and structural integrity.
โœ… Footings โ€“ Improve stability and prevent settlement.
โœ… Beams โ€“ Restore and upgrade strength for better performance.

๐ŸšงWhy Retrofitting?

๐Ÿ”น Extend Structural Lifespan โ€“ Protect your investment for years to come.
๐Ÿ”น Improve Safety โ€“ Ensure compliance with modern building codes and standards.
๐Ÿ”น Cost-Effective โ€“ Avoid expensive replacements by strengthening existing structures.
๐Ÿ”น Resilience Against Disasters โ€“ Strengthen your building to withstand seismic activity and heavy loads.

๐Ÿ“ž Contact Us Today!

๐Ÿ“ฉ @pragmaengineering
๐Ÿ“ฑ +251975889929 | +251941099797

Pragma Engineering โ€“ Your Trusted Partner in Structural Excellence!
๐Ÿ‘4๐Ÿ‘4โค1