Forwarded from Ethio Construction Engineering
👉ኣሁን ደሞ ስለ Lap length እንማማር @COTMp
.
▶Lap length in Reinforced
Concrete Lap length is one of the important term in the reinforcement. This is usually confused with
another important term called development length and anchorage length.
In this article, the lap lengths of bars is discussed. During the
placement of steel in Reinforced concrete
structure , if the required length of single bar
may fall short. To get the desired design length, lapping of two bars side by side is done.
An alternative to this is to provide mechanical couplers.
*steel bars overlapped
Lapping can be defined as the overlapping of two bars side by side to upto the design length. Usually, the stock length of steel bars is limited to 12m. *This is for easy
transportation of steel bars to the construction
site. For example, imagine there is a need to build a 100ft tall column. But it’s not practically available. Hence the bars are cut
every second story.
steel bars overlapped Then the tension forces are required to be transferred from one bar to the other bar at the location of discontinuity of the bar.
So the second bar is kept closely to the first bar and
overlapping is done.
This amount of overlapping between two bars is called “lap length”. *Lapping is usually done where minimum bending stress is encountered. In
general, lap length is 50d which means 50 times the bar diameter, if both bars are of same diameter.
*Lap length of bars with same diameter Lap length in tension: The lap length including anchorage value of hooks shall be For flexural tension – Ld or 30d whichever is greater is considered.
*For direct tension – 2Ld or 30d whichever is greater is considered.
*The straight length of lapping of bars shall not
be less than 15d or 20cm.
Lap Length in Compression: The lap length is equal to the development length calculated in compression but not less than 24d.
*For Different Diameter Bars: When the bars of different diameters are to be spliced, the lap length is calculated considering
the smaller diameter bar.
*Lap Splices:- Lap splices should not be catered for the bars
which are having diameter greater than 36 mm.
In such cases, welding should be considered.
*But if welding is also not feasible in some conditions, then lapping may be allowed for the bars larger than 36 mm diameter. But along with lapping, additional spirals of 6 mm should be provided around the lapped bars.
*Lap splice length in a footing Lap length for concrete of 1:2:3 Nominal mix: The Lapping length in tension (MS bar – mild
steel bar) including anchorage value is 58d. So
eliminating the anchorage value, the lap length
= 58d – 2*9d = 40d. (Where 9d = hook
*allowance up to 25 mm and k=2)
*Lap length for C-25 concrete:
*Columns – 45d
*Beams – 60d
*Slabs – 60d
This infers that if we need to lap 20 mm diameter column bars, a minimum lap of 45 * 20 = 900 mm is provided.
.
👇👇👇👇👇
Join for more updates via the link below;
t.me/COTMp
👆👆👆👆👆
⚡ አሁኑኑ Join በማረግ እና ለጓደኛዎ እና ለሚያቁት ሁሉ ሼር ያድርጉ።
.
▶Lap length in Reinforced
Concrete Lap length is one of the important term in the reinforcement. This is usually confused with
another important term called development length and anchorage length.
In this article, the lap lengths of bars is discussed. During the
placement of steel in Reinforced concrete
structure , if the required length of single bar
may fall short. To get the desired design length, lapping of two bars side by side is done.
An alternative to this is to provide mechanical couplers.
*steel bars overlapped
Lapping can be defined as the overlapping of two bars side by side to upto the design length. Usually, the stock length of steel bars is limited to 12m. *This is for easy
transportation of steel bars to the construction
site. For example, imagine there is a need to build a 100ft tall column. But it’s not practically available. Hence the bars are cut
every second story.
steel bars overlapped Then the tension forces are required to be transferred from one bar to the other bar at the location of discontinuity of the bar.
So the second bar is kept closely to the first bar and
overlapping is done.
This amount of overlapping between two bars is called “lap length”. *Lapping is usually done where minimum bending stress is encountered. In
general, lap length is 50d which means 50 times the bar diameter, if both bars are of same diameter.
*Lap length of bars with same diameter Lap length in tension: The lap length including anchorage value of hooks shall be For flexural tension – Ld or 30d whichever is greater is considered.
*For direct tension – 2Ld or 30d whichever is greater is considered.
*The straight length of lapping of bars shall not
be less than 15d or 20cm.
Lap Length in Compression: The lap length is equal to the development length calculated in compression but not less than 24d.
*For Different Diameter Bars: When the bars of different diameters are to be spliced, the lap length is calculated considering
the smaller diameter bar.
*Lap Splices:- Lap splices should not be catered for the bars
which are having diameter greater than 36 mm.
In such cases, welding should be considered.
*But if welding is also not feasible in some conditions, then lapping may be allowed for the bars larger than 36 mm diameter. But along with lapping, additional spirals of 6 mm should be provided around the lapped bars.
*Lap splice length in a footing Lap length for concrete of 1:2:3 Nominal mix: The Lapping length in tension (MS bar – mild
steel bar) including anchorage value is 58d. So
eliminating the anchorage value, the lap length
= 58d – 2*9d = 40d. (Where 9d = hook
*allowance up to 25 mm and k=2)
*Lap length for C-25 concrete:
*Columns – 45d
*Beams – 60d
*Slabs – 60d
This infers that if we need to lap 20 mm diameter column bars, a minimum lap of 45 * 20 = 900 mm is provided.
.
👇👇👇👇👇
Join for more updates via the link below;
t.me/COTMp
👆👆👆👆👆
⚡ አሁኑኑ Join በማረግ እና ለጓደኛዎ እና ለሚያቁት ሁሉ ሼር ያድርጉ።
Telegram
ETCONp Discussion
📩ለማነኛውም ሀሳብ እና አስተያየት @Philemona7
✌️ይህ የ @etconp መወያያ ግሩፓቹ ነው።
✋This is discussion group of @ETCONpWORK
.
🔖ማሳሰብያ ...
.
⚡️ግሩፑ ላይ ማነኛውም ከ ኮንስትራክሽን ጉዳዮች ውጪ መለጠፍ በፍፁም አይፈቀድም!
@ETCONpBOT ፃፉልን እናመሰግናለን🙏
✌️ይህ የ @etconp መወያያ ግሩፓቹ ነው።
✋This is discussion group of @ETCONpWORK
.
🔖ማሳሰብያ ...
.
⚡️ግሩፑ ላይ ማነኛውም ከ ኮንስትራክሽን ጉዳዮች ውጪ መለጠፍ በፍፁም አይፈቀድም!
@ETCONpBOT ፃፉልን እናመሰግናለን🙏
❤1
Forwarded from Ethio Construction Engineering (FILA)
❇️የውሃ ጋኖች (water supply Reservoir)
.
የውሃ ጋኖች ከጥቅማቸው አንፃር ለ ሶስት ይከፈላሉ
.
1-Collector reservoir
2-Service reservoir
3-Supply reservoir
.
እያንዳንዱ ጥቅማቸው ምንድነው……
✅1 [Collector reservoir ]
.
ይህ የጋን አይነት ዋና ስራው ውሃው ከሚመነጭበት (የገጸ ምድር ወይም የከርሰ ምድር ውሃ) ቦታ ህክምና ከተደረገለት በኋላ የሚቀመጥበት ጋን ነው፡፡ ጥቅሙ የተሰበሰበውን ውሃ ወደተለያዩ ጋኖች እስኪሰራጭ በጊዜያዊነት እንዲቀመጥና ውሃው ለጋኖቹ እንዲደርስ የሚያደርገውን ጉልበት እንዲያገኝ ይረዳዋል፡፡ ብዙን ጊዜ ውሃው ከሚመነጭበት ቦታ አቅራቢያ ይተከላል፡፡ ውሃ ፈሳሽ እንደመሆኑ ብዙን ግዜ ሚፈልቀው ከፍታቸው ካነሱ ቦታዎች ስለሆነ ከሌሎች ጋኖች ይልቅ የዚህ ጋን ከፍታ (elevation) ያንሳል፡፡
.
✅2 [Service reservoir]
.
ይህ የጋን አይነት በቋሚነት ከcollecter reservoir የተቀበለውን ውሃ የሚያርፍበት ነው፡፡ አሰራሩም ከሌሎቹ ጋኖች ለየት ይላል ፡፡ ውሃው የሚያደርስበትን ግፊት ለመቋቋም የሚያስቸለውን መካች ጉልበት(reaction force) በበቂ ሁኔታ እንዲኖረው ይደረጋል፡፡ በቁመትም በመጠንም ትልቅ ነው፡፡ ወጪ ለመቀነስ ከፍ ካለ ቦታ ይተከላል (ውሃ በ3 አይነት መንገድ ይከፋፈላል
.
1-የሞተር ሀይልን በመጠቀም
2-የመሬት የመሳብ ሃይልን (gravity force) በመጠቀም።
3-የሞተር ሃይልንና የመሬት የስበት ሃይልን በማጣመር በመጠቀም እንዲሰራጭ ይደረጋል፡፡
፡
በአሁን ጊዜ ሶስተኛው አማራጭ በስፋታ አገልግሎት ላይ ይውላል ይህ አማራጭ ከወጪም አንፃር በጣም ተመራጭ ነው ለዚህ ዘዴ ተመራጩ ደግሞ የservice reservoir ከፍ ካለ ቦታላይ መተከል ወሳኝነት አለው፡፡)
ከዚህ ጋን ቀጥታ ለስርጭት ቧንቧ አይገጠምም ምክንያቱም ከጋኑ የሚወጣው ውሃ ከፍተኛ ጉልበት ስላለው የማሰራጫ ቱቦዎችን ሊያፈነዳ ይችላል፡፡ ይህን ችግር ለመፍታት ቀጣዩን የጋን አይነት መገንባት አስፈላጊ ነው፡፡
.
✅3.[Supply reservoir]
፡
የዚህ ጋን ዋና ጥቅም ውሃውን ለስርጭት ወደ ስርጭት ቱቦዎች እንዲገባ ማድረግ ነው፡፡ ከላይ እንደጠቀስኩት ከሰርቪስ ጋን ቀጥታ ወደ ስርጭት ቧንቧ ውሃ አይገባም ምክንያቱም ከፍተኛ ሀይል ስላለው የቧንቧዎቹን የመቆየት አቅም ያሳጥራል ብሎም እስከ ማፈንዳት ያደርሳል፡፡ ይህ እንዳይከሰት የሳፕላይ ጋኖች ይገነባሉ፡፡ ይህ ጋን በቱቦዎቹ የሚያልፈውን ውሃ ግፊት በመቀነስና ፈጥነቱን (velocity) ከ 0.5-2 m/s በማድረግ እና ወደ ቱቦዎቹ የሚገባን ሃይል በመቀነስ (Energy dissipate ) ቱቦዎቹ ላይ የሚደርሰውን ጉዳት ያስወግዳል፡፡ ይህ ጋን ከፍ ባለ ቦታ ይተከላል ነገር ግን ከፍታው ከService reservoir ያነሰ ነው። እናመሰግናለን።
፡
▶️SHARE SHARE SHARE
.
የውሃ ጋኖች ከጥቅማቸው አንፃር ለ ሶስት ይከፈላሉ
.
1-Collector reservoir
2-Service reservoir
3-Supply reservoir
.
እያንዳንዱ ጥቅማቸው ምንድነው……
✅1 [Collector reservoir ]
.
ይህ የጋን አይነት ዋና ስራው ውሃው ከሚመነጭበት (የገጸ ምድር ወይም የከርሰ ምድር ውሃ) ቦታ ህክምና ከተደረገለት በኋላ የሚቀመጥበት ጋን ነው፡፡ ጥቅሙ የተሰበሰበውን ውሃ ወደተለያዩ ጋኖች እስኪሰራጭ በጊዜያዊነት እንዲቀመጥና ውሃው ለጋኖቹ እንዲደርስ የሚያደርገውን ጉልበት እንዲያገኝ ይረዳዋል፡፡ ብዙን ጊዜ ውሃው ከሚመነጭበት ቦታ አቅራቢያ ይተከላል፡፡ ውሃ ፈሳሽ እንደመሆኑ ብዙን ግዜ ሚፈልቀው ከፍታቸው ካነሱ ቦታዎች ስለሆነ ከሌሎች ጋኖች ይልቅ የዚህ ጋን ከፍታ (elevation) ያንሳል፡፡
.
✅2 [Service reservoir]
.
ይህ የጋን አይነት በቋሚነት ከcollecter reservoir የተቀበለውን ውሃ የሚያርፍበት ነው፡፡ አሰራሩም ከሌሎቹ ጋኖች ለየት ይላል ፡፡ ውሃው የሚያደርስበትን ግፊት ለመቋቋም የሚያስቸለውን መካች ጉልበት(reaction force) በበቂ ሁኔታ እንዲኖረው ይደረጋል፡፡ በቁመትም በመጠንም ትልቅ ነው፡፡ ወጪ ለመቀነስ ከፍ ካለ ቦታ ይተከላል (ውሃ በ3 አይነት መንገድ ይከፋፈላል
.
1-የሞተር ሀይልን በመጠቀም
2-የመሬት የመሳብ ሃይልን (gravity force) በመጠቀም።
3-የሞተር ሃይልንና የመሬት የስበት ሃይልን በማጣመር በመጠቀም እንዲሰራጭ ይደረጋል፡፡
፡
በአሁን ጊዜ ሶስተኛው አማራጭ በስፋታ አገልግሎት ላይ ይውላል ይህ አማራጭ ከወጪም አንፃር በጣም ተመራጭ ነው ለዚህ ዘዴ ተመራጩ ደግሞ የservice reservoir ከፍ ካለ ቦታላይ መተከል ወሳኝነት አለው፡፡)
ከዚህ ጋን ቀጥታ ለስርጭት ቧንቧ አይገጠምም ምክንያቱም ከጋኑ የሚወጣው ውሃ ከፍተኛ ጉልበት ስላለው የማሰራጫ ቱቦዎችን ሊያፈነዳ ይችላል፡፡ ይህን ችግር ለመፍታት ቀጣዩን የጋን አይነት መገንባት አስፈላጊ ነው፡፡
.
✅3.[Supply reservoir]
፡
የዚህ ጋን ዋና ጥቅም ውሃውን ለስርጭት ወደ ስርጭት ቱቦዎች እንዲገባ ማድረግ ነው፡፡ ከላይ እንደጠቀስኩት ከሰርቪስ ጋን ቀጥታ ወደ ስርጭት ቧንቧ ውሃ አይገባም ምክንያቱም ከፍተኛ ሀይል ስላለው የቧንቧዎቹን የመቆየት አቅም ያሳጥራል ብሎም እስከ ማፈንዳት ያደርሳል፡፡ ይህ እንዳይከሰት የሳፕላይ ጋኖች ይገነባሉ፡፡ ይህ ጋን በቱቦዎቹ የሚያልፈውን ውሃ ግፊት በመቀነስና ፈጥነቱን (velocity) ከ 0.5-2 m/s በማድረግ እና ወደ ቱቦዎቹ የሚገባን ሃይል በመቀነስ (Energy dissipate ) ቱቦዎቹ ላይ የሚደርሰውን ጉዳት ያስወግዳል፡፡ ይህ ጋን ከፍ ባለ ቦታ ይተከላል ነገር ግን ከፍታው ከService reservoir ያነሰ ነው። እናመሰግናለን።
፡
▶️SHARE SHARE SHARE
Forwarded from Ethio Construction Engineering (जॉर्डनो ג׳ורדנו ጆርዳኖ جوردانو จอร์แดโน่ JORDANO Ιορδάνοςஜார்டானோ)
Elements of building
Forwarded from Ethio Construction Engineering (जॉर्डनो ג׳ורדנו ጆርዳኖ جوردانو จอร์แดโน่ JORDANO Ιορδάνοςஜார்டானோ)
This media is not supported in your browser
VIEW IN TELEGRAM
👉A turned mass damper (TMD) also known as a harmonic absorber or seismic damper is a device mounted in structures to reduce the amplitude of mechanical vibrations. Their application can prevent discomfort, damage or outright structural failure. They are frequently used in power transmission, automobiles and buildings @cotmp. #share
https://t.me/COTMp
https://t.me/COTMp
This media is not supported in your browser
VIEW IN TELEGRAM
👉Construction Engineers change every rules 🏗
:
▶️The road between china & pakistan
:
👉transportation engineering @ETCONp
.
🅾አሁኑኑ Join በማረግ እና ለጓደኛዎ እና ለሚያቁት ሁሉ ሼር ያድርጉ።
:
▶️The road between china & pakistan
:
👉transportation engineering @ETCONp
.
🅾አሁኑኑ Join በማረግ እና ለጓደኛዎ እና ለሚያቁት ሁሉ ሼር ያድርጉ።
Ethio Construction Engineering
👉 @COTMp Types-of-Cracks-in-Concrete-Columns-
👉 Reasons for cause and description of type of cracks @ETCONp
1. Diagonal Cracks
The main cause of diagonal cracks in concrete columns is 👉 Inadequate load carrying capacity of the columns;
👉 insufficient cross-section and inadequate reinforcement steel.
👉 Diagonal Cracks would influence structural soundness and hence it needs to be dealt with.
2. Horizontal Cracks
👉 Horizontal crack in reinforced concrete column is observed to initiate mostly at the beam-column junction, and on column face where tensile stress is large.
👉 Columns with in adequate moment resistance capacity,
👉 Insufficient reinforcements, or disposition of installed reinforcement are prone to horizontal cracking
👉 Horizontal cracks substantially reduce the shear strength of the column leading to a greatly increased risk of failure. So, it is required to be tackled as soon as
3. Splitting Cracks
👉 Splitting cracks in reinforced concrete column are short parallel vertical cracks with non-uniform width.
👉 Columns with Insufficient steel reinforcement, and low concrete quality are susceptible to experience such types of cracks.
👉 Splitting cracks in concrete columns initiated as a result of reaching its maximum load carrying capacity.
4. Corrosion Cracks
👉 Corrosion cracks in concrete columns are developed along the line of reinforcements.
👉 This type of cracks is commonly uniform in width and widen as the column is ageing.
👉 Possible reinforcement corrosion and inadequate bond between concrete and steel bars are the cause of corrosion reinforcement in concrete columns.
1. Diagonal Cracks
The main cause of diagonal cracks in concrete columns is 👉 Inadequate load carrying capacity of the columns;
👉 insufficient cross-section and inadequate reinforcement steel.
👉 Diagonal Cracks would influence structural soundness and hence it needs to be dealt with.
2. Horizontal Cracks
👉 Horizontal crack in reinforced concrete column is observed to initiate mostly at the beam-column junction, and on column face where tensile stress is large.
👉 Columns with in adequate moment resistance capacity,
👉 Insufficient reinforcements, or disposition of installed reinforcement are prone to horizontal cracking
👉 Horizontal cracks substantially reduce the shear strength of the column leading to a greatly increased risk of failure. So, it is required to be tackled as soon as
3. Splitting Cracks
👉 Splitting cracks in reinforced concrete column are short parallel vertical cracks with non-uniform width.
👉 Columns with Insufficient steel reinforcement, and low concrete quality are susceptible to experience such types of cracks.
👉 Splitting cracks in concrete columns initiated as a result of reaching its maximum load carrying capacity.
4. Corrosion Cracks
👉 Corrosion cracks in concrete columns are developed along the line of reinforcements.
👉 This type of cracks is commonly uniform in width and widen as the column is ageing.
👉 Possible reinforcement corrosion and inadequate bond between concrete and steel bars are the cause of corrosion reinforcement in concrete columns.
Revised_RMT_Unit 1.ppt
396.5 KB
▶️For any members that is currently doing research here is amazing guidelines to follow
.
👉Research Methodology course files to refer! @ETCONp
.
👉Research Methodology course files to refer! @ETCONp
Revised_RMT_Unit 4.ppt
152 KB
▶️For any members that is currently doing research here is amazing guidelines to follow
.
👉Research Methodology course files to refer! @ETCONp
.
👉Research Methodology course files to refer! @ETCONp
Revised_RMT_Unit 6_2.ppt
120.5 KB
▶️For any members that is currently doing research here is amazing guidelines to follow
.
👉Research Methodology course files to refer! @ETCONp
.
👉Research Methodology course files to refer! @ETCONp
Revised_RMT_Unit 3.ppt
352.5 KB
▶️For any members that is currently doing research here is amazing guidelines to follow
.
👉Research Methodology course files to refer! @ETCONp
.
👉Research Methodology course files to refer! @ETCONp
Revised_RMT_Unit 6_1.ppt
175.5 KB
▶️For any members that is currently doing research here is amazing guidelines to follow
.
👉Research Methodology course files to refer! @ETCONp
.
👉Research Methodology course files to refer! @ETCONp
Revised_RMT_Unit 5.ppt
976 KB
▶️For any members that is currently doing research here is amazing guidelines to follow
.
👉Research Methodology course files to refer! @ETCONp
.
👉Research Methodology course files to refer! @ETCONp
Revised_RMT_Unit 2.ppt
515.5 KB
▶️For any members that is currently doing research here is amazing guidelines to follow
.
👉Research Methodology course files to refer! @ETCONp
.
👉Research Methodology course files to refer! @ETCONp
👆👆👆👆👆👆👆👆👆👆👆👆
:
▶️TODAY GREAT TIP @ETCONp
:
👉አብዛኛዎቻቹ በጠየቃችሁን መሰረት ለ ሪሰርች እና THESIS ኣጋዥ የሆን ፋይሎች እንካቹ ብለናል፡፡
፡
🅾አሁኑኑ Join በማረግ እና ለጓደኛዎ እና ለሚያቁት ሁሉ ሼር ያድርጉ።
:
▶️TODAY GREAT TIP @ETCONp
:
👉አብዛኛዎቻቹ በጠየቃችሁን መሰረት ለ ሪሰርች እና THESIS ኣጋዥ የሆን ፋይሎች እንካቹ ብለናል፡፡
፡
🅾አሁኑኑ Join በማረግ እና ለጓደኛዎ እና ለሚያቁት ሁሉ ሼር ያድርጉ።
Forwarded from Ethio Construction Engineering (जॉर्डनो ג׳ורדנו ጆርዳኖ جوردانو จอร์แดโน่ JORDANO Ιορδάνοςஜார்டானோ)
This media is not supported in your browser
VIEW IN TELEGRAM
Forwarded from Ethio Construction Engineering (जॉर्डनो ג׳ורדנו ጆርዳኖ جوردانو จอร์แดโน่ JORDANO Ιορδάνοςஜார்டானோ)
This media is not supported in your browser
VIEW IN TELEGRAM
Dynamic compaction of soil #soilmechanics#compaction
👉ወድ የቻናላችን ቤተሰቦች እንዴት ናችሁልን? ለዛሬ ኣንድ መወያያ ሀሳብ ይዘናል ሀሳባቹ አካፍሉን...
:
▶️አንድ የስራ አይተም የስራ ዝርዝር(specification) ፣መለኪያ(unit) ኖሮት የስራ መጠን (quantity) ባዶ ሆኖ (ሳይኖረው)ዋጋ (rate) የተሞላ ቢሆን እና በስራ ወቅት የስራ መጠኑ ከባዶ ወደ 1000(ምሳሌ ነው) ቢሆን የውል አካል ሆኖ በተሞላው ዋጋ ይከፈላል? የውሉ አካልስ ነው?ወይስ በምን መልኩ ነው የሚስተናገድ?
፡
👉ሀሳባቹ Discussion ወይም @COTMp ላይ አካፍሉን
፡
https://t.me/COTMp
:
▶️አንድ የስራ አይተም የስራ ዝርዝር(specification) ፣መለኪያ(unit) ኖሮት የስራ መጠን (quantity) ባዶ ሆኖ (ሳይኖረው)ዋጋ (rate) የተሞላ ቢሆን እና በስራ ወቅት የስራ መጠኑ ከባዶ ወደ 1000(ምሳሌ ነው) ቢሆን የውል አካል ሆኖ በተሞላው ዋጋ ይከፈላል? የውሉ አካልስ ነው?ወይስ በምን መልኩ ነው የሚስተናገድ?
፡
👉ሀሳባቹ Discussion ወይም @COTMp ላይ አካፍሉን
፡
https://t.me/COTMp
Telegram
ETCONp Discussion
📩ለማነኛውም ሀሳብ እና አስተያየት @Philemona7
✌️ይህ የ @etconp መወያያ ግሩፓቹ ነው።
✋This is discussion group of @ETCONpWORK
.
🔖ማሳሰብያ ...
.
⚡️ግሩፑ ላይ ማነኛውም ከ ኮንስትራክሽን ጉዳዮች ውጪ መለጠፍ በፍፁም አይፈቀድም!
@ETCONpBOT ፃፉልን እናመሰግናለን🙏
✌️ይህ የ @etconp መወያያ ግሩፓቹ ነው።
✋This is discussion group of @ETCONpWORK
.
🔖ማሳሰብያ ...
.
⚡️ግሩፑ ላይ ማነኛውም ከ ኮንስትራክሽን ጉዳዮች ውጪ መለጠፍ በፍፁም አይፈቀድም!
@ETCONpBOT ፃፉልን እናመሰግናለን🙏