Ethio Construction Engineering
32.3K subscribers
6.28K photos
359 videos
1.99K files
3.34K links
๐Ÿ”จ World Construction Engineering
Latest updates, tips, and tutorials on building, civil engineering, and construction in World.
Learn, build, and grow with us!

๐Ÿ“จ @Philemona7 Or @ETCONpBOT

For Ad:- https://telega.io/c/etconp
Download Telegram
Civil engineering huge machinery ๐Ÿ‘‡๐Ÿ‘‡๐Ÿ‘‡๐Ÿ‘‡๐Ÿ‘‡
DEEP BEAMS
Deep beams are Reinforced concrete structural elements with large depths in relation to their spans. A deep beam is a beam in which a significant amount of the load is carried to the supports by a compression thrust joining the load and the reactions. According to the EBCS 2 1995, beams are considered as deep beams when
l/hโ‰ค...2 for simple span
...2.5 for continuous
Where l is the effective span measured center to center of supports or 1.15 times clear span, whichever is smaller and h is the overall depth of the deep beam.
Deep beams are usually found at at transfer girders (girders support one or more columns transferring it laterally to other columns) used in multistory buildings to provide column offset , in foundation wall, pile cap rectangular suspended containers (tanks), raft slabs, pile caps, floor diaphragms, shear walls etc.
Behavior of Deep Beams
The behavior of deep beams is significantly different from that of beams of normal proportion (shallow beams) that it requires special consideration in analysis, design and detailing of reinforcement. Elastic analysis of such beams indicates that the usual hypothesis plane section before bending remains plane after bending is not valid for such members. Thus flexural stresses are not linearly distributed even in the elastic range and hence the usual methods used for analysis and design of ordinary reinforced concrete beams are neither suitable nor adequate to determine the strength of reinforced concrete deep beams.
The followings are the major different of deep beam element compared with ordinary beam:
๏ถ Two-Dimensional Action: because of the dimension of deep beam they behave as two-
dimensional action rather than one-dimensional action.
๏ถ Plane Section Do Not Remain Plane: the assumption of plane section remains plane cannot
be used in the deep beam design. The strain distribution is no longer linear.
๏ถ Shear Deformation: the shear deformation cannot be neglected as ๏ถ The stress distribution is not linear even in the elastic stage. At the ultimate limit state the
shape of concrete compressive stress block is not parabolic shape again.
๏ถ The distribution of tensile stress at bottom fiber is constant over the span. In other word the value of tensile stress at bottom fiber at support and at mid span is only little different, for this reason in deep beam the tension reinforcement must be extend to the end of support although that region is small bending moment region (in ordinary beam we can cut off the tension reinforcement and not all of the tension reinforcement in mid span is extended to the end of support, practically only two for anchor the stirrups).
๏ถ The maximum tensile stress at the bottom fiber is far exceeding the magnitude of
compressive stress.

For more information u can join us on
๐Ÿ‘‡๐Ÿ‘‡๐Ÿ‘‡๐Ÿ‘‡๐Ÿ‘‡๐Ÿ‘‡๐Ÿ‘‡
http://t.me/COTMp
๐Ÿ‘†๐Ÿ‘†๐Ÿ‘†๐Ÿ‘†๐Ÿ‘†๐Ÿ‘†๐Ÿ‘†
๐Ÿ‘1
Concrete Cover Blocks is also known as Spacers which is used to provide
spacing at Slab, Column, Beam & foundation.

Application is very simple
as place COVER BLOCK between Rebar (Reinforcement bar) and ground/wall.


Spacers are used to provide specific height for your concrete reinforcement structure before pouring.
There are four types of cover block or Spacers!
1. Slab Cover
2. Column & Beam Cover
3. Foundation Cover
4. Piling Cover

Various Photographs of Cover Blocks according to itโ€™s type, โฌ‡๏ธโฌ‡๏ธโฌ‡๏ธโฌ‡๏ธโฌ‡๏ธ
Analysis and Design of Curved Beam

Reinforced concrete curved beams arse extensively used to support circular walls of RC water tanks, curved balconies, circular domes, modern highway intersection, the rounded corners of buildingsโ€ฆ.etc. In some of these cases, large depths are needed for curved beams in order to resist high loads or to fulfill some aesthetic purposes. The analytical analysis of such members is very complex due to the fact that those members are subjected to a combined action of bending, shear and torsion. Furthermore, non-homogeneous nature of the materials involved contributes to the complexity of the problem. Therefore, it becomes necessary to employ numerical analysis procedures, such as finite element method, to satisfy safe and the economy requirements. A curved beam, loaded transversely to its plane, is subjected to torsion in addition to bending and shear. Furthermore, in deep beam the plane section does not remain plane after bending because of high stresses and warping occurs. RC curved beams are:-
๏ƒ˜ Supported on columns spaced at regular intervals.
๏ƒ˜ Torsional moments are develop at certain sections of curved beams. ๏ƒ˜ Maximum torsion developed at the position of zero bending moment. ๏ƒ˜ Maximum negative and positive moments developed @ supports and mid spans respectively.

Design Considerations of Curved beams
๏ƒ˜ Torsional shear stresses create diagonal tension resulting in diagonal crack. Thus we need to provide both closed stirrups and longitudinal steel to avoid brittle fracture.
The torsional resistance of any section may be computed on the basis of an equivalent hollow section. hef , Aef ,
hef โ‰ค A/U & Aef = bโ€™* hโ€™
๏ƒ˜ The centerlines of the longitudinal reinforcement are taken as the centerline of the
equivalent hollow section.
๏ƒ˜ The limiting value of ultimate torque : to prevent diagonal compression failure,
TRD = 0.8*fcd*Aef*hef
๏ƒ˜ Torsional effect may be neglected when the Tsd (design torque) is less than Tc
(the torque resistance of section)
Tc = 1.2*fctd*Aef*hef
๏ƒ˜ However minimum web reinforcement provided ๏ฒ min=0.6 / fyk or Spacing of
stirrups shall not exceed Uef / 8 for torsion.
๏ƒ˜ If the section capacity against diagonal compression, TRD< Tsd, the section is
too small. Section should be increased.
๏ƒ˜ Longitudinal bars for torsion shall be distributed uniformly around the
perimeter of the closed stirrups at a spacing not exceeding 350mm.
.
.
.
For more updates join us via the link below
๐Ÿ‘‡๐Ÿ‘‡๐Ÿ‘‡๐Ÿ‘‡๐Ÿ‘‡๐Ÿ‘‡๐Ÿ‘‡๐Ÿ‘‡๐Ÿ‘‡
t.me/COTMp
โ˜โ˜โ˜โ˜โ˜โ˜โ˜โ˜โ˜โ˜
let's Safe & Develop the construction Industry!
.
You Can contact us on

๐Ÿ‘‰ @GN510636
โ™ฃ แˆตแˆˆ construction technology and management program objective, mission and vision แˆแŠ• แ‹ซแˆ…แˆ แ‹ซแ‹แ‰ƒแˆ‰?

โ˜… Objective โ€“ the Objective of this program is to produce outstanding construction technology and management graduates who have been prepared to become technological, managerial and public service leaders capable of understanding the social and environmental challenges that face the country, and who will be in a position to make a meaningful contribution to both national social and economic growth and development as well as being able to respond to, and benefit from, the impact of global change. The department and the staff are committed to creating a learning environment that provides a level of knowledge and competency in these areas, through an innovative program of study, supported by a capability in information technology use, coupled with a capacity to integrate the key social and environmental issues facing the country. This program is aimed primarily at training managing engineers required for managing constructing projects with efficient and effective management system, Administer contracts, Conduct researches to identify real problems on site pertaining to construction management, methods & materials, and find better solutions

โ˜…Vision

The Department of Construction Technology and Management aspires to excel in teaching, problem solving and community based research, and industry linkage at regional, national as well as international level; to produce competent engineers within the field of construction technology and management.

โ˜…Mission

The mission of Construction Technology and Management Department is to:

A. Train students to help develop a knowledge base in mathematics, science, engineering, and technology to support planning, analyzing, and solving of engineering and construction problems using state of the art management and design tools and techniques.

B. Produce professionals who will have leadership skills, and effective verbal, non-verbal, and interpersonal skills to support their role in industry.

C. Train students who will demonstrate appropriate mastery of knowledge, techniques, skills, and up-to-date tools of construction

http://t.me/COTMp
๐Ÿ‘2
แ‰ แ‹แˆตแŒฅ แˆ˜แˆตแˆ˜แˆญ แ‰ แŒ แ‹จแ‰ƒแ‰นแ‰ต แˆ˜แˆฐแˆจแ‰ต แ‰€แˆต แ‰ แ‰€แˆต แ‹จแˆแˆ‹แ‰นแŠ•แˆ แŒฅแ‹ซแ‰„ แŠจแАแŒˆ แŒ€แˆแˆฎ แˆˆแˆ˜แˆ˜แˆˆแˆต แŠฅแŠ•แˆžแŠญแˆซแˆˆแŠ•แข แˆˆแˆŒแˆŽแ‰ฝ แŠฅแŠ•แ‹ฒแ‹ฐแˆญแˆต แˆผแˆญ แ‰ แˆ›แ‹ตแˆจแŒ แŠฅแŠ“ แ‰ แˆ˜แˆณแ‰ฐแ แŠ แ‰ฅแˆซแ‰นแŠ• แŠฅแŠ•แ‹ตแ‰ตแ‰†แ‹ฉ แŠฅแŠ•แŒ แ‹ญแ‰ƒแˆˆแŠ•แข