👉PROPERTIES OF PORTLAND CEMENT @COTMp
.
▶️(i) Chemical properties: Portland cement consists of the following chemical compounds:
(a) Tricalcium silicate 3 CaO.SiO2 (C3S) 40%
(b) Dicalcium silicate 2CaO.SiO2 (C2S) 30%
(c) Tricalcium aluminate 3CaO.Al2O3 (C3A) 11%
(d) Tetracalcium aluminate 4CaO.Al2O3.Fe2O3 (C3AF) 11%
There may be small quantities of impurities present such as calcium oxide (CaO) and magnesium oxide (MgO). When water is added to cement, C3A is the first to react and cause initial set. It generates great amount of heat. C3S hydrates early and develops strength in the first 28 days. It also generates heat. C2S is the next to hydrate. It hydrates slowly and is responsible for increase in ultimate strength. C4AF is comparatively inactive compound.
.
▶️(ii) Physical properties:
The following physical properties should be checked before selecting a portland cement for the civil engineering works. IS 269–1967 specifies the method of testing and prescribes the limits:
(a) Fineness (b) Setting time
(c) Soundness (d) Crushing strength.
(a) Fineness:
.
*It is measured in terms of percentage of weight retained after sieving the cement through 90 micron sieve or by surface area of cement in square centimeters per gramme of cement. According to IS code specification weight retained on the sieve should not be more than 10 per cent. In terms of specific surface should not be less than 2250 cm2/gm.
(b) Setting time:
A period of 30 minutes as minimum setting time for initial setting and a maximum period of 600 minutes as maximum setting time is specified by IS code, provided the tests are conducted as per the procedure prescribed by IS 269-1967.
.
(c) Soundness:
Once the concrete has hardened it is necessary to ensure that no volumetric changes takes place. The cement is said to be unsound, if it exhibits volumetric instability after hardening. IS code recommends test with Le Chatelier mould for testing this property. At the end of the test, the indicator of Le Chatelier mould should not expand by more than 10 mm.
***(a) Crushing strength:
For this mortar cubes are made with standard sand and tested in compression testing machine as per the specification of IS code. The minimum strength specified is 16 N/mm2 after 3 days and 22 N/mm2 after 7 days of curing.
:
http://t.me/ETCONp
.
▶️(i) Chemical properties: Portland cement consists of the following chemical compounds:
(a) Tricalcium silicate 3 CaO.SiO2 (C3S) 40%
(b) Dicalcium silicate 2CaO.SiO2 (C2S) 30%
(c) Tricalcium aluminate 3CaO.Al2O3 (C3A) 11%
(d) Tetracalcium aluminate 4CaO.Al2O3.Fe2O3 (C3AF) 11%
There may be small quantities of impurities present such as calcium oxide (CaO) and magnesium oxide (MgO). When water is added to cement, C3A is the first to react and cause initial set. It generates great amount of heat. C3S hydrates early and develops strength in the first 28 days. It also generates heat. C2S is the next to hydrate. It hydrates slowly and is responsible for increase in ultimate strength. C4AF is comparatively inactive compound.
.
▶️(ii) Physical properties:
The following physical properties should be checked before selecting a portland cement for the civil engineering works. IS 269–1967 specifies the method of testing and prescribes the limits:
(a) Fineness (b) Setting time
(c) Soundness (d) Crushing strength.
(a) Fineness:
.
*It is measured in terms of percentage of weight retained after sieving the cement through 90 micron sieve or by surface area of cement in square centimeters per gramme of cement. According to IS code specification weight retained on the sieve should not be more than 10 per cent. In terms of specific surface should not be less than 2250 cm2/gm.
(b) Setting time:
A period of 30 minutes as minimum setting time for initial setting and a maximum period of 600 minutes as maximum setting time is specified by IS code, provided the tests are conducted as per the procedure prescribed by IS 269-1967.
.
(c) Soundness:
Once the concrete has hardened it is necessary to ensure that no volumetric changes takes place. The cement is said to be unsound, if it exhibits volumetric instability after hardening. IS code recommends test with Le Chatelier mould for testing this property. At the end of the test, the indicator of Le Chatelier mould should not expand by more than 10 mm.
***(a) Crushing strength:
For this mortar cubes are made with standard sand and tested in compression testing machine as per the specification of IS code. The minimum strength specified is 16 N/mm2 after 3 days and 22 N/mm2 after 7 days of curing.
:
http://t.me/ETCONp
Telegram
Ethio Construction Engineering
🔨 World Construction Engineering
Latest updates, tips, and tutorials on building, civil engineering, and construction in World.
Learn, build, and grow with us!
📨 @Philemona7 Or @ETCONpBOT
For Ad:- https://telega.io/c/etconp
Latest updates, tips, and tutorials on building, civil engineering, and construction in World.
Learn, build, and grow with us!
📨 @Philemona7 Or @ETCONpBOT
For Ad:- https://telega.io/c/etconp
👉ይቺ ናት ኢትዮጵያ ይቺ ናት ሀገሬ @ETCONp
:
▶️ኢትዮጵያ ሀገራችንን በበጎ ስራ እናገልግል የምህንድስና ሙያን ወደ ከፍታው እንመልስ!!
፡
🙏"ፈጣሪ ኢትዮጵያ እና ህዝቦቿን አብዝቶ ይባርክ!!"🙏
:
👇👇👇👇👇👇👇👇
:
▶️ኢትዮጵያ ሀገራችንን በበጎ ስራ እናገልግል የምህንድስና ሙያን ወደ ከፍታው እንመልስ!!
፡
🙏"ፈጣሪ ኢትዮጵያ እና ህዝቦቿን አብዝቶ ይባርክ!!"🙏
:
👇👇👇👇👇👇👇👇
👆👆👆👆👆👆👆👆👆👆
.
👉ይቺ ናት ኢትዮጵያ ይቺ ናት ሀገሬ @ETCONp
:
▶️ኢትዮጵያ ሀገራችንን በበጎ ስራ እናገልግል የምህንድስና ሙያን ወደ ከፍታው እንመልስ!!
፡
🙏"ፈጣሪ ኢትዮጵያ እና ህዝቦቿን አብዝቶ ይባርክ!!"🙏
.
👉ይቺ ናት ኢትዮጵያ ይቺ ናት ሀገሬ @ETCONp
:
▶️ኢትዮጵያ ሀገራችንን በበጎ ስራ እናገልግል የምህንድስና ሙያን ወደ ከፍታው እንመልስ!!
፡
🙏"ፈጣሪ ኢትዮጵያ እና ህዝቦቿን አብዝቶ ይባርክ!!"🙏
👉8 CAUSES OF CRACKS IN CONCRETE YOU SHOULD KNOW
:
▶️Cracking is one of the most common problems in concrete and it should be avoided seriously.
*Different causes of cracks in concrete are described below:
.
1. SHRINKAGE:
*Shrinkage is one of the major causes of cracking in hardened concrete.
*In drying shrinkage, the volume of concrete is gradually decreased and if the component is restrained against free movement, tensile stresses are developed which causes cracks.
.
2. TEMPERATURE CHANGES:
The temperature variation in concrete results in the differential volume change.
*When the tensile strain capacity of concrete exceeds due to the differential volume change, it will crack.
.
3. CHEMICAL REACTION:
Due to the alkaline nature of cement, it reacts with the carbon dioxide (CO2) present in the atmosphere resulting in an appreciable increase in the volume of the materials which
finally leads to cracking.
.
4. POOR CONSTRUCTION PRACTICES:
Poor construction practices such as adding excessive water to the mix, lack of curing, poor compaction, using low-grade materials, unreasonable placements of construction joints etc. are also responsible for cracking in concrete.
.
5. ERRORS IN DESIGN & DETAILING:
Errors in design and detailing such as an inadequate amount of reinforcement, improper design of foundation, precast members and slabs, improper selection of materials, lack of sufficient contraction joints etc may result in excessive cracking.
.
6. CONSTRUCTION OVERLOADS & EARLY
FORMWORK REMOVAL:
The load induced in the structure during construction can also lead to cracking especially at the younger stage when the
formwork is removed earlier.
.
7. ELASTIC DEFORMATION AND CREEP:
The different components of the building such as wall, column, beam. slab etc undergo elastic deformation when loaded.
*The deformation of concrete depends on the type of building materials used in the constructio such as bricks, cement concrete blocks etc.
*This unusual deformation of concrete results
in cracking.
.
8. CORROSION OF CONCRETE:
The corrosion of steel develops a huge amount of iron oxides and hydroxide that have a much greater volume than the volume of metallic iron. Hence the volume is increased
:
https://t.me/COTMp
:
▶️Cracking is one of the most common problems in concrete and it should be avoided seriously.
*Different causes of cracks in concrete are described below:
.
1. SHRINKAGE:
*Shrinkage is one of the major causes of cracking in hardened concrete.
*In drying shrinkage, the volume of concrete is gradually decreased and if the component is restrained against free movement, tensile stresses are developed which causes cracks.
.
2. TEMPERATURE CHANGES:
The temperature variation in concrete results in the differential volume change.
*When the tensile strain capacity of concrete exceeds due to the differential volume change, it will crack.
.
3. CHEMICAL REACTION:
Due to the alkaline nature of cement, it reacts with the carbon dioxide (CO2) present in the atmosphere resulting in an appreciable increase in the volume of the materials which
finally leads to cracking.
.
4. POOR CONSTRUCTION PRACTICES:
Poor construction practices such as adding excessive water to the mix, lack of curing, poor compaction, using low-grade materials, unreasonable placements of construction joints etc. are also responsible for cracking in concrete.
.
5. ERRORS IN DESIGN & DETAILING:
Errors in design and detailing such as an inadequate amount of reinforcement, improper design of foundation, precast members and slabs, improper selection of materials, lack of sufficient contraction joints etc may result in excessive cracking.
.
6. CONSTRUCTION OVERLOADS & EARLY
FORMWORK REMOVAL:
The load induced in the structure during construction can also lead to cracking especially at the younger stage when the
formwork is removed earlier.
.
7. ELASTIC DEFORMATION AND CREEP:
The different components of the building such as wall, column, beam. slab etc undergo elastic deformation when loaded.
*The deformation of concrete depends on the type of building materials used in the constructio such as bricks, cement concrete blocks etc.
*This unusual deformation of concrete results
in cracking.
.
8. CORROSION OF CONCRETE:
The corrosion of steel develops a huge amount of iron oxides and hydroxide that have a much greater volume than the volume of metallic iron. Hence the volume is increased
:
https://t.me/COTMp
Telegram
ETCONp Discussion
📩ለማነኛውም ሀሳብ እና አስተያየት @Philemona7
✌️ይህ የ @etconp መወያያ ግሩፓቹ ነው።
✋This is discussion group of @ETCONpWORK
.
🔖ማሳሰብያ ...
.
⚡️ግሩፑ ላይ ማነኛውም ከ ኮንስትራክሽን ጉዳዮች ውጪ መለጠፍ በፍፁም አይፈቀድም!
@ETCONpBOT ፃፉልን እናመሰግናለን🙏
✌️ይህ የ @etconp መወያያ ግሩፓቹ ነው።
✋This is discussion group of @ETCONpWORK
.
🔖ማሳሰብያ ...
.
⚡️ግሩፑ ላይ ማነኛውም ከ ኮንስትራክሽን ጉዳዮች ውጪ መለጠፍ በፍፁም አይፈቀድም!
@ETCONpBOT ፃፉልን እናመሰግናለን🙏
Forwarded from Deleted Account
Tanzania_Field Testing Manual (2003).pdf
8.1 MB