Ethio Construction Engineering
32.3K subscribers
6.27K photos
359 videos
1.99K files
3.33K links
🔨 World Construction Engineering
Latest updates, tips, and tutorials on building, civil engineering, and construction in World.
Learn, build, and grow with us!

📨 @Philemona7 Or @ETCONpBOT

For Ad:- https://telega.io/c/etconp
Download Telegram
📖✔IMPORTANT POINTS FROM THERNAL STRESSES (STRENGTH_OF_MATERIALS)

✔ Stresses produced due to change in temperatures(Rise/Fall) are called as thermal stresses

✔ Actual meaning of coefficient of thermal expansion is strain produced per unit change in temperature

✔Unit of Coefficient of thermal expansion = per degree celcius

✔ Coefficient of thermal expansion for different materials
✴ Aluminium = 24 x 10^(-6)
✴ Copper = 17.5 x 10^(-6)
✴ Steel = 12 x 10^(-6)

✔Higher the value of coefficient of thermal expansion, more will be the material sensitive for temperature change

✔For the bar free to expand, with change in temperature (rise/fall), no stress is developed

✔Prismatic bar with rigidly supported at both ends
✔ As temperature increases, compressive stresses are developes on bar
✔ As temperature decreases, tensile stresses are developes on bar

✔ Copper bar is in series with steel bar
✔ As temperature increases, compressive stresses are developed on both copper and steel bar
✔ As temperature decreases, tensile stresses are developed on both copper and steel bar

✔ Copper plate is in parallel with steel plate and form a composite
✔ As temperature increases, compressive stress developed on copper and tensile stress developed on steel
✔ As temperature decreases, tensile stress developed on copper and compressive stress developed on steel

✔ Copper rod is enclosed in steel tube and both are rigidly fixed at ends
✔As temperature increases, Compressive stresses are developes on both copper and steel
✔ As temperature decreases, tensile stresses are developes on both copper and steel.
👍1
What is the name of these test performed on a ground surface?
Anonymous Quiz
25%
Cone penetration test
14%
Standard penetration test
52%
Field density test
9%
Plate load tesr
It is called field density test(FDT) using sand replacement method.

There are different methods used to determine the density of a compacted soil. Sand replacement method is one of them.

FDT test is probably the most frequently applied field test in a construction site. Before placing any RC structures( foundation,grade beam, grade slab..) into the ground surface, FDT should be performed and should pass the test.

FDT Is performed to determine the degree of compaction of a ground surface. Degree of compaction is given in a percentile value. As per AASHTO standard, insitu degree of compaction should be more than 95%. This means the on-site soil density must be atleast 95% of the maximum achievable compaction.

This is done first by determining the maximum dry density(MDD) and optimum moisture content(OMC) of the compacted fill material in the laboratory.

Next task is to compare the MDD value with that of the insitu dry density value.
The basic principle of sand replacement method is to measure the insitu volume of hole from which the material was excavated from the weight of sand with known density filling the hole. The insitu density of material is given by the weight of excavated material divided by insitu volume.

The sand replacement method can be a little bit tricky. It will better to check the procedure on a YouTube tutorial.

Note regarding FDT
-Considering a compaction thickness of 25cm,one FDT in every 200m3 should be taken.
- if the FDT failed,then the entire fill material is removed, replaced by another material and again compacted well.
-performing FDT prior to construction Is important in checking the stability of ground surface.

Part of report below from our project shows FDT test result and the obtained degree of compaction.👷‍♂️✌

@etconp
👍1
እናት ባንክ headquarter

@etconp
Forwarded from Samuel H
👍1