RCC Marathon PDF notes and

@etconp

Reinforced concrete design
______

@etconp

💥 New RCC Handwritten Notes

@etconp

Reference Book RCC

@etconp

👉ውድ ቤተሰቦቻችን ለ ዛሬ የ RCC አሪፍ ኖት ከነ የተሰሩ ምሳሌዎች ጋር ልናጋራቹ ወደናል።

🌟እናንተም ለወዳጆቻቹ በማጋራት ኣግዙን።

⚡️Best Notes and worked Exampls Of Roller Compacted Concrete Course 👆👆👆

@etconp

👉Stress vs strain

⚡️Part 1

🌟Stress is the ratio of applied force F to a cross section area defined as "force per unit area".
tensile stress - stress that tends to stretch or lengthen the material - acts normal to the stressed area compressive stress - stress that tends to compress or shorten the material - acts normal to the stressed area

⏺shearing stress - stress that tends to shear the material - acts in plane to the stressed area at right-angles to
compressive or tensile stress

⏺Tensile or Compressive Stress - Normal Stress

▶️Tensile or compressive stress normal to the plane is usually denoted "normal stress " or "direct stress " and can be
expressed as

σ = F n / A (1)

where

σ = normal stress (Pa (N/m 2 ), psi (lb f /in 2 ))
F n = normal force acting perpendicular to the area (N, lb f)
A = area (m 2 , in 2 )
a kip is an imperial unit of force - it equals 1000 lb f (pounds-force)
1 kip = 4448.2216 Newtons (N) = 4.4482216 kilo Newtons (kN)

▶️A normal force acts perpendicular to area and is developed whenever external loads tends to push or pull the two segments of a body.

🚧Example - Tensile Force acting on a Rod A force of 10 kN is acting on a circular rod with diameter 10 mm The stress in the rod can be calculated as

σ = (10 10 3 N) / (π ((10 10 -3 m) / 2) 2 )
= 127388535 (N/m 2 )
= 127 (MPa)

🚧Example - Force acting on a Douglas Fir Square Post A compressive load of 30000 lb is acting on short square 6 x 6 in post of Douglas fir. The dressed size of the post is 5.5 x 5.5 in and the compressive stress can be calculated as

σ = (30000 lb) / ((5.5 in) (5.5 in))
= 991 (lb/in 2 , psi)

⏺Shear Stress

▶️Stress parallel to a plane is usually denoted as "shear stress "and can be expressed as

τ = F p / A (2)
where
τ = shear stress (Pa (N/m 2 ), psi (lb f /in 2 ))
F p = shear force in the plane of the area (N, lb f)
A = area (m 2 , in 2 )

▶️A shear force lies in the plane of an area and is developed when external loads tend to cause the two segments of a body to slide over one another.

Facebook:- https://www.facebook.com/etconp/

Telegram:- https://t.me/ETCONpWORK

YouTube:- https://youtube.com/@Etconp432

💫Comment @ETCONpBot

♡ ㅤ   ❍ㅤ    ⎙ㅤ    ⌲
ˡᶦᵏᵉ   ᶜᵒᵐᵐᵉⁿᵗ  ˢᵃᵛᵉ    ˢʰᵃʳᵉ

╔═════
    🌐   join 👇
   @ETCONp
   @COTMp
╚══ ☆☆☆☆☆══════