Ethio Construction Engineering
Typical Contour line
👉ስለ Contour Lines ኣብረን እንይ
፡
▶️Characteristics of contour lines are:
1. Connect point of equal elevation.
2. Always connects close contour lines. This is not always visible on the map.
3. They never cross, split or intersect – at a cliff they might merge.
4. Evenly spaced contour lines indicate a uniform slope.
5. Closely spaced contour lines show a steep slope.
6. Widely spaced contour lines show gentle slope.
7. Uneven spacing – irregular or variable slope.
9. Closed contours with arrow in the centre represent depressions.
፡
▶️Other characteristics of contour lines are:
- Horizontal distance between contour lines is inversely proportional to slope.
- Uniform slopes have uniformly spaced lines.
- Along plane surfaces, contour lines are straight and parallel.
- Contour lines are perpendicular to lines of steepest slopes.
- For summits or depressions, contour lines most close upon themselves.
- A single contour line can not lie between two lines of higher or lower elevation.
፡
▶️There are some basic rules for contour lines:
1. A contour line must never split or divide.
2. A contour line must never simply end, except at the edge of the map.
3. A contour line must represent one and only one elevation.
4. A contour line may never intersect other contour lines. Overhanging cliffs are
the only exception.
5. Concentric circles of contour lines indicate a hilltop or mountain peak.
6. Concentric circles of hatched contour lines indicate a closed depression.
.
👇👇👇👇👇
👉Join for more Construction updates Join via the link below;👇
t.me/COTMp
👆👆👆👆👆
⚡ አሁኑኑ Join በማረግ እና ለጓደኛዎ እና ለሚያቁት ሁሉ ሼር ያድርጉ።
፡
▶️Characteristics of contour lines are:
1. Connect point of equal elevation.
2. Always connects close contour lines. This is not always visible on the map.
3. They never cross, split or intersect – at a cliff they might merge.
4. Evenly spaced contour lines indicate a uniform slope.
5. Closely spaced contour lines show a steep slope.
6. Widely spaced contour lines show gentle slope.
7. Uneven spacing – irregular or variable slope.
9. Closed contours with arrow in the centre represent depressions.
፡
▶️Other characteristics of contour lines are:
- Horizontal distance between contour lines is inversely proportional to slope.
- Uniform slopes have uniformly spaced lines.
- Along plane surfaces, contour lines are straight and parallel.
- Contour lines are perpendicular to lines of steepest slopes.
- For summits or depressions, contour lines most close upon themselves.
- A single contour line can not lie between two lines of higher or lower elevation.
፡
▶️There are some basic rules for contour lines:
1. A contour line must never split or divide.
2. A contour line must never simply end, except at the edge of the map.
3. A contour line must represent one and only one elevation.
4. A contour line may never intersect other contour lines. Overhanging cliffs are
the only exception.
5. Concentric circles of contour lines indicate a hilltop or mountain peak.
6. Concentric circles of hatched contour lines indicate a closed depression.
.
👇👇👇👇👇
👉Join for more Construction updates Join via the link below;👇
t.me/COTMp
👆👆👆👆👆
⚡ አሁኑኑ Join በማረግ እና ለጓደኛዎ እና ለሚያቁት ሁሉ ሼር ያድርጉ።
Telegram
ETCONp Discussion
📩ለማነኛውም ሀሳብ እና አስተያየት @Philemona7
✌️ይህ የ @etconp መወያያ ግሩፓቹ ነው።
✋This is discussion group of @ETCONpWORK
.
🔖ማሳሰብያ ...
.
⚡️ግሩፑ ላይ ማነኛውም ከ ኮንስትራክሽን ጉዳዮች ውጪ መለጠፍ በፍፁም አይፈቀድም!
@ETCONpBOT ፃፉልን እናመሰግናለን🙏
✌️ይህ የ @etconp መወያያ ግሩፓቹ ነው።
✋This is discussion group of @ETCONpWORK
.
🔖ማሳሰብያ ...
.
⚡️ግሩፑ ላይ ማነኛውም ከ ኮንስትራክሽን ጉዳዮች ውጪ መለጠፍ በፍፁም አይፈቀድም!
@ETCONpBOT ፃፉልን እናመሰግናለን🙏
👉 ግሪን ኮንክሪት ያውቃሉ
፡
▶️What is Green Concrete?
፡
🏙Green Concrete is made from concrete wastes that are eco-friendly are called as “Green concrete”. Green Concrete is a term given to a concrete that has had extra steps taken in the mix design and placement to insure a sustainable structure and a long life cycle with a low maintenance surface. e.g. Energy saving, CO2 emissions, wastewater.
፡
Today the word green is not just limited to colour, it represents the environment, which is surrounding us.
፡
“Green concrete” is a revolutionary topic in the history of concrete industry. This was first invented in Denmark in the year 1998 by Dr.WG.
፡
Concrete wastes like slag, power plant wastes, recycled concrete, mining and quarrying wastes, waste glass, incinerator residue, red mud, burnt clay, sawdust, combustor ash and foundry sand.
፡
The goal of the Centre for Green Concrete is to reduce the environmental impact of concrete. To enable this, new technology is developed. The technology considers all phases of a concrete construction’s life cycle, i.e. structural design, specification, manufacturing and maintenance, and it includes all aspects of performance, i.e.
፡
Mechanical properties (strength, shrinkage, creep, static behaviour etc.)Fire resistance (spalling, heat transfer etc.)Workmanship (workability, strength development, curing etc.)Durability (corrosion protection, frost, new deterioration mechanisms etc.)Thermodynamic properties (input to the other properties)Environmental aspects (CO2-emission, energy, recycling etc.)
፡
There are a number of alternative environmental requirements with which green concrete structures must comply:
፡
CO2 emissions shall be reduced by at least 30 %.At least 20 % of the concrete shall be residual products used as aggregate.Use of concrete industries own residual products.Use of new types of residual products, previously land filled or disposed of in other ways.CO2-neutral, waste-derived fuels shall substitute fossil fuels in the cement production by at least 10 %.
፡
In addition to the environmental goals there are a number of environmental intentions. Most important are:
፡
To avoid the use of materials which contain substances on the Environmental Protection Agency’s list of unwanted materials, not to reduce the recycling ability of green concrete compared with conventional concrete and not to increase the content of hazardous substances in the wastewater from concrete production compared with wastewater from production of existing concrete types.
፡
Different concrete types are tested for workability, changes in workability after 30 min., air-content, compressive strength development, E-modulus, heat development, homogeneity, water separation, setting time, density and pumpability. Furthermore, frost testing, chloride penetration and an air void analysis are carried out for the concretes in the aggressive environmental class.
፡
The water/cement ratio, water/binder ratio and the chloride content are calculated from the mixing report of the precise mixture proportions and from the chloride content in the different raw materials.
፡
▶️Advantages of Green Concrete
Reduction of the concrete industry’s CO2-emmision by 30 %.Increased concrete industry’s use of waste products by 20%.NO environmental pollution and sustainable development.Green concrete requires less maintenance and repairs.Green concrete having better workability than conventional concrete.Good thermal resistant and fire resistant.Compressive strength behaviour of ceracrete with water cement ratio is similar to conventional concrete.Flexural strength of green concrete is almost equal to that of conventional concrete.
፡
▶️Limitations of Green Concrete
፡
By using stainless steel, cost of reinforcement increases.Structures constructed with green concrete have comparatively less life than structures with conventional concrete.Split tension of green concrete is less than that of conventional concrete.
፡
👇👇👇👇👇
👉Join for more Construction updates Join via the link below;👇
t.me/COTMp
👆👆👆👆👆
⚡ አሁኑኑ Join በማረግ ለጓደኛዎም SHARE ያርጉ
፡
▶️What is Green Concrete?
፡
🏙Green Concrete is made from concrete wastes that are eco-friendly are called as “Green concrete”. Green Concrete is a term given to a concrete that has had extra steps taken in the mix design and placement to insure a sustainable structure and a long life cycle with a low maintenance surface. e.g. Energy saving, CO2 emissions, wastewater.
፡
Today the word green is not just limited to colour, it represents the environment, which is surrounding us.
፡
“Green concrete” is a revolutionary topic in the history of concrete industry. This was first invented in Denmark in the year 1998 by Dr.WG.
፡
Concrete wastes like slag, power plant wastes, recycled concrete, mining and quarrying wastes, waste glass, incinerator residue, red mud, burnt clay, sawdust, combustor ash and foundry sand.
፡
The goal of the Centre for Green Concrete is to reduce the environmental impact of concrete. To enable this, new technology is developed. The technology considers all phases of a concrete construction’s life cycle, i.e. structural design, specification, manufacturing and maintenance, and it includes all aspects of performance, i.e.
፡
Mechanical properties (strength, shrinkage, creep, static behaviour etc.)Fire resistance (spalling, heat transfer etc.)Workmanship (workability, strength development, curing etc.)Durability (corrosion protection, frost, new deterioration mechanisms etc.)Thermodynamic properties (input to the other properties)Environmental aspects (CO2-emission, energy, recycling etc.)
፡
There are a number of alternative environmental requirements with which green concrete structures must comply:
፡
CO2 emissions shall be reduced by at least 30 %.At least 20 % of the concrete shall be residual products used as aggregate.Use of concrete industries own residual products.Use of new types of residual products, previously land filled or disposed of in other ways.CO2-neutral, waste-derived fuels shall substitute fossil fuels in the cement production by at least 10 %.
፡
In addition to the environmental goals there are a number of environmental intentions. Most important are:
፡
To avoid the use of materials which contain substances on the Environmental Protection Agency’s list of unwanted materials, not to reduce the recycling ability of green concrete compared with conventional concrete and not to increase the content of hazardous substances in the wastewater from concrete production compared with wastewater from production of existing concrete types.
፡
Different concrete types are tested for workability, changes in workability after 30 min., air-content, compressive strength development, E-modulus, heat development, homogeneity, water separation, setting time, density and pumpability. Furthermore, frost testing, chloride penetration and an air void analysis are carried out for the concretes in the aggressive environmental class.
፡
The water/cement ratio, water/binder ratio and the chloride content are calculated from the mixing report of the precise mixture proportions and from the chloride content in the different raw materials.
፡
▶️Advantages of Green Concrete
Reduction of the concrete industry’s CO2-emmision by 30 %.Increased concrete industry’s use of waste products by 20%.NO environmental pollution and sustainable development.Green concrete requires less maintenance and repairs.Green concrete having better workability than conventional concrete.Good thermal resistant and fire resistant.Compressive strength behaviour of ceracrete with water cement ratio is similar to conventional concrete.Flexural strength of green concrete is almost equal to that of conventional concrete.
፡
▶️Limitations of Green Concrete
፡
By using stainless steel, cost of reinforcement increases.Structures constructed with green concrete have comparatively less life than structures with conventional concrete.Split tension of green concrete is less than that of conventional concrete.
፡
👇👇👇👇👇
👉Join for more Construction updates Join via the link below;👇
t.me/COTMp
👆👆👆👆👆
⚡ አሁኑኑ Join በማረግ ለጓደኛዎም SHARE ያርጉ
Telegram
ETCONp Discussion
📩ለማነኛውም ሀሳብ እና አስተያየት @Philemona7
✌️ይህ የ @etconp መወያያ ግሩፓቹ ነው።
✋This is discussion group of @ETCONpWORK
.
🔖ማሳሰብያ ...
.
⚡️ግሩፑ ላይ ማነኛውም ከ ኮንስትራክሽን ጉዳዮች ውጪ መለጠፍ በፍፁም አይፈቀድም!
@ETCONpBOT ፃፉልን እናመሰግናለን🙏
✌️ይህ የ @etconp መወያያ ግሩፓቹ ነው።
✋This is discussion group of @ETCONpWORK
.
🔖ማሳሰብያ ...
.
⚡️ግሩፑ ላይ ማነኛውም ከ ኮንስትራክሽን ጉዳዮች ውጪ መለጠፍ በፍፁም አይፈቀድም!
@ETCONpBOT ፃፉልን እናመሰግናለን🙏
👍1
Shear Strength of Soil by Vane Shear Test
Apparatus
Apparatus required for vane shear test are:
Vane shear apparatusSoil specimen containerVernier callipers.
Vane shear apparatus consists high tensile steel rod to which four steel blades (vanes) are fixed at right angles to each other at the bottom of rod.
Procedure of Vane Shear Test
Test procedure of vane shear test contains following steps:
Clean the vane shear apparatus and apply grease to the lead screw for better movement of handles.Take the soil specimen in container which is generally 75 mm in height and 37.5 mm in diameter.Level the soil surface on the top and mount the container on the base of vane shear test apparatus using screws provided.Lower the vane gradually into the soil specimen until the top of vane is at a depth of 10 to 20 mm below the top of soil specimen.
Note down the reading of pointer on circular graduated scale which is initial reading.Rotate the vane inside the soil specimen using torque applying handle at a rate of 0.1o per second.When the specimen fails, the strain indicator pointer will move backwards on the circular graduated scale and at this point stop the test and note down the final reading of pointer.The difference between Initial and final readings is nothing but the angle of torque.Repeat the procedure on two more soil specimens and calculate the average shear strength value.Measure the diameter and height of vane using Vernier callipers.Sensitivity of given soil sample is determined by repeating the above test procedure on remolded soil which is nothing but soil obtained after rapid stirring of vane in the above test.
Sensitivity of soil = undisturbed shear strength/ remolded shear strength.
Observations and Calculations of Vane Shear Test
Shear strength of given soil sample is calculated from below observations.
Diameter of vane, D = _ cmHeight of vane, H = __ cmTorque, T = (Spring constant /180)*(initial reading-final reading)
Shear strength of soil (S) is calculated from below formula.
.
http://t.me/COTMp
Apparatus
Apparatus required for vane shear test are:
Vane shear apparatusSoil specimen containerVernier callipers.
Vane shear apparatus consists high tensile steel rod to which four steel blades (vanes) are fixed at right angles to each other at the bottom of rod.
Procedure of Vane Shear Test
Test procedure of vane shear test contains following steps:
Clean the vane shear apparatus and apply grease to the lead screw for better movement of handles.Take the soil specimen in container which is generally 75 mm in height and 37.5 mm in diameter.Level the soil surface on the top and mount the container on the base of vane shear test apparatus using screws provided.Lower the vane gradually into the soil specimen until the top of vane is at a depth of 10 to 20 mm below the top of soil specimen.
Note down the reading of pointer on circular graduated scale which is initial reading.Rotate the vane inside the soil specimen using torque applying handle at a rate of 0.1o per second.When the specimen fails, the strain indicator pointer will move backwards on the circular graduated scale and at this point stop the test and note down the final reading of pointer.The difference between Initial and final readings is nothing but the angle of torque.Repeat the procedure on two more soil specimens and calculate the average shear strength value.Measure the diameter and height of vane using Vernier callipers.Sensitivity of given soil sample is determined by repeating the above test procedure on remolded soil which is nothing but soil obtained after rapid stirring of vane in the above test.
Sensitivity of soil = undisturbed shear strength/ remolded shear strength.
Observations and Calculations of Vane Shear Test
Shear strength of given soil sample is calculated from below observations.
Diameter of vane, D = _ cmHeight of vane, H = __ cmTorque, T = (Spring constant /180)*(initial reading-final reading)
Shear strength of soil (S) is calculated from below formula.
.
http://t.me/COTMp
Telegram
ETCONp Discussion
📩ለማነኛውም ሀሳብ እና አስተያየት @Philemona7
✌️ይህ የ @etconp መወያያ ግሩፓቹ ነው።
✋This is discussion group of @ETCONpWORK
.
🔖ማሳሰብያ ...
.
⚡️ግሩፑ ላይ ማነኛውም ከ ኮንስትራክሽን ጉዳዮች ውጪ መለጠፍ በፍፁም አይፈቀድም!
@ETCONpBOT ፃፉልን እናመሰግናለን🙏
✌️ይህ የ @etconp መወያያ ግሩፓቹ ነው።
✋This is discussion group of @ETCONpWORK
.
🔖ማሳሰብያ ...
.
⚡️ግሩፑ ላይ ማነኛውም ከ ኮንስትራክሽን ጉዳዮች ውጪ መለጠፍ በፍፁም አይፈቀድም!
@ETCONpBOT ፃፉልን እናመሰግናለን🙏
Human resource management in construction lecture notes
This media is not supported in your browser
VIEW IN TELEGRAM
This helmet fan keeps you cool in the summer.
This media is not supported in your browser
VIEW IN TELEGRAM
3 ways for demolishing skyscrapers
This media is not supported in your browser
VIEW IN TELEGRAM
Marvellous Bridge
This media is not supported in your browser
VIEW IN TELEGRAM
how unsafe the use of mobile during work !!!
This media is not supported in your browser
VIEW IN TELEGRAM
Efficiently remove manholes with the help of this machine.
This media is not supported in your browser
VIEW IN TELEGRAM
Smart Tile Fixing Ideas
This media is not supported in your browser
VIEW IN TELEGRAM
Workers can prevent injuries with the help of this gorilla gripper
This media is not supported in your browser
VIEW IN TELEGRAM
Automatic Plastering Machine
👉Great Today Tip 👆👆👆
.
➡ለዛሬ የተለያዩ ጠቃሚ ቪዲዮዎች እንካቹ ብሎናል
.
🅾በኢትዮጵያ ለመጀመሪያ ጊዜ
🅾አሁኑኑ Join በማረግ እና ለጓደኛዎ እና ለሚያቁት ሁሉ ሼር ያድርጉ።
.
➡ለዛሬ የተለያዩ ጠቃሚ ቪዲዮዎች እንካቹ ብሎናል
.
🅾በኢትዮጵያ ለመጀመሪያ ጊዜ
🅾አሁኑኑ Join በማረግ እና ለጓደኛዎ እና ለሚያቁት ሁሉ ሼር ያድርጉ።