👉ሁለት ቤተመንግስቶች የባለ አምስት ኮከብ ሆቴል አገልግሎት መስጠት ሊጀምሩ ነው

💫በኢትዮጵያ ቤተመንግስት አስተዳደር ስር የሚተዳደሩት ድሬዳዋ ቤተ መንግስት እና የጅማ ግቤ አዳራሽ ባለ አምስት ኮከብ ሆቴል የሚያደርጋቸው ግንባታ ወደ መጨረሻው ምዕራፍ መድረሱን አራዳ ከኢትዮጵያ ቤተ መንግስት አስተዳደር ዋና ዳይሬክተር ምትኩ ኩምሳ ሰምቷል።

⏺የድሬዳዋ ቤተመንግስት የሆቴል ግንባታው ከሦስት ዓመታት በፊት ተጀምሮ አሁን ወደ መጠናቀቂያው ምዕራፍ ላይ ደርሷል።

🚧በጅማ የሚገኘው ግቤ አራዳሽ የሆቴሉ ግንባታ በሸራተን አዲስ ሆቴል ድርጅት የተከናወነ ሲሆን፣፥ ሸራተን ኢንቨስት ያደረገበትን ሆቴል ለሦስት ዓመታት ወጪውን ለመተካት ከተገለገለበት በኋላ ለቦታው የኪራይ ክፍያ ለመንግስት መፈፀም እንደሚጀምር ተመላክቷል።

💫በሁለቱም ቤተመንግስቶች ቀዳማዊ አፄ ኃይለስላሴ የኢትዮጵያ ንጉስ ሳሉ ይጠቀሙባቸው የነበሩ ቤቶች የቅርስ ይዘታቸው ሳይነካ ተጨማሪ ግንባታዎችን በማከል ለአገልግሎት ዝግጁ እየተደረጉ ነው።

Via አራዳ ኤፍ ኤም

@etconp

👉የግንባታ ደህንነት

💫Construction Safety

🏷Addis Abeba's construction boom is coming under scrutiny as city authorities announce a crackdown on unsafe practices across 24,000 active sites starting July 12, 2025.

⏺A task force led by Wendimu Seta, the city’s general manager, will inspect sites for compliance with safety standards, with immediate suspensions and demolitions for violations.

⏺The initiative seeks to address systemic issues discussed in a high-level forum, where officials cited 142 recorded worker fatalities since 2022.

📜Read more👇

https://ow.ly/Zws750WlAYz

Via Addis Fortune

@etconp

ታምራት  ፕሌት እና ጄቦልት አቅራቢ

♧ ሁሉን በአንድ ቦታ ለሁሉም ቅርብ

📍ኢትዮጵያ ዉስጥ የትም እንልክሎታለን

♧ ይደውሉልን ያማክሩን

0904040477
0994941708

👉Standard Penetration Test (SPT) – Essential Soil Investigation Tool

⏺When it comes to foundation design and geotechnical engineering, understanding the soil behavior beneath a construction site is non-negotiable.

⏺One of the most common and reliable methods used worldwide for subsurface investigation is the Standard Penetration Test (SPT).

📜Let’s break it down clearly:

❇️What is Standard Penetration Test (SPT)?

▶️The Standard Penetration Test (SPT) is an in-situ dynamic penetration test carried out in boreholes to determine the geotechnical properties of soil. It provides an indication of the soil's strength, density, and bearing capacity — essential parameters for safe and economical foundation design.

▶️The test is widely used for both sand and clay soils and forms an integral part of site investigations for buildings, bridges, roads, and other infrastructure.

💫How is the SPT Conducted?

⏺The process involves the following steps:

🚧 A borehole is drilled to the desired depth using rotary or percussion drilling methods.

🚧 A split-spoon sampler (a thick-walled cylindrical tube) is placed at the bottom of the borehole.

🚧 A 63.5kg (140 lbs) hammer is dropped from a height of 760mm (30 inches) repeatedly to drive the sampler into the soil.

🚧 The number of hammer blows required to drive the sampler 150mm (6 inches) at three consecutive intervals is recorded.

🚧 The sum of the blows required for the second and third 150mm penetration is called the N-Value or SPT Blow Count.

🏷Understanding the SPT N-Value

⏺The N-Value is a measure of soil resistance to penetration and gives vital information about the soil's characteristics:

🚧N-Value Range Soil Condition

0 - 4 Very Loose/Soft Soil
5 - 10 Loose Soil
11 - 30 Medium Dense/Compact
31 - 50 Dense Soil
>50 Very Dense/Hard Soil

@etconp

👉What is the purpose of adding Admixture ?

⭐️Concrete admixtures are added to concrete mixes to modify and enhance the properties of the concrete, both in its fresh and hardened states.

📜Here's a breakdown of the key reasons:

🚧Improved Workability:

⏺Admixtures can make concrete easier to mix, place, and finish.

⏺This is especially important for complex pours or when working in difficult conditions.

🚧Enhanced Strength:

⏺Certain admixtures can increase the compressive and flexural strength of concrete, leading to more durable and robust structures.

🚧Increased Durability:

⏺Admixtures can improve concrete's resistance to environmental factors like freeze-thaw cycles, chemical attacks, and abrasion.

🚧Modified Setting Time:

⏺Admixtures can accelerate or retard the setting time of concrete, allowing for adjustments based on project needs and weather conditions.

🚧Water Reduction:

⏺Water-reducing admixtures allow for the production of stronger, more durable concrete with less water, which improves the water to cement ratio.

🚧Specialized Applications:

⏺Admixtures can be used to achieve specific properties, such as air entrainment for improved freeze-thaw resistance or coloring for aesthetic purposes.

💫In essence, concrete admixtures provide a way to tailor concrete mixes to meet the specific requirements of a wide range of construction projects.

@etconp

👉እንዴት ነው ክረምቱ ወዳጆቼ?

💫እስቲ ለ ክረምታቹ የሚሆን የምታነቡት ምን ኣይነት የ PDF መፅሐፍ ወይም ፋይል እንላክላቹ

🏷የትም አላገኘሁትም አጣሁት የምትሉት ካለም አሳውቁን

🚧ሰብሰብ አርገን ማታ እዚሁ እንለጥፈዋለን🙏

📩ሀሳብ፣ጥያቄ እና አስተያየት ካሎት በ @Philemona7 ፃፉልን❤

Ethio Construction Engineering

@etconp

#ADVERTISEMENT

🏭🏠TSEGAYE and YOHANNES J-Bolt & PLATE 🏚🏗 🌁🌆

🧿 OUR SERVICES ⤵️

🔲Plate

⚙️  J-Bolt

⚓Anchor Bolt

➽Tie Rod

Phone : 🤳0938494506 
              🤳 0951087077
              🤳 0929044037

👉አድራሻ፦  መርካቶ ምንአለሽ ተራ ከጭድ ተራ ከፍ ብሎ

https://t.me/tsegaye2016Jbolt

👉Curing time for prime coat?

🚧Curing of a prime coat in road construction is the process where the applied material (e.g., cutback asphalt or emulsified asphalt) sets and achieves its intended properties, such as penetration, adhesion, and sealing.

🎲Proper curing is critical for effective bonding between the base course and asphalt layer. Below is a concise guide on prime coat curing:

⭐️Key Aspects of Prime Coat Curing

⏺1. Curing Mechanism:

   - Cutback Asphalt (e.g., MC-30, MC-70): Cures through the evaporation of the solvent (e.g., kerosene or naphtha), leaving behind a thin asphalt film that binds to the base.
   - Emulsified Asphalt (e.g., CSS-1, SS-1): Cures through "breaking" of the emulsion, where water evaporates, and asphalt particles coalesce to form a cohesive layer.

⏺2. Curing Time:

   - Cutback Asphalt: Typically 12–24 hours, depending on the solvent type, application rate (0.4–1.2 kg/m²), and environmental conditions.
   - Emulsified Asphalt: Typically 24–48 hours, as water evaporation is slower than solvent-based materials.
   - Factors Affecting Curing:
     - Temperature: Higher temperatures (above 20°C) accelerate curing; below 10°C, curing slows significantly.
     - Humidity: High humidity delays emulsion curing due to slower water evaporation.
     - Ventilation: Good airflow speeds up solvent or water evaporation.
     - Base Porosity: More porous bases (e.g., WMM) may require longer curing for deeper penetration.

⏺3. Curing Process Guidelines:

   - Apply Uniformly: Ensure even application (using a calibrated distributor) to avoid pooling, which can delay curing.
   - Protect the Surface: Restrict traffic and heavy equipment to prevent damage to the curing coat. Use barriers or signs as needed.
   - Monitor Weather: Avoid application if rain is expected within the curing period, as moisture can disrupt the process or wash away the prime coat.
   - Check Penetration: The prime coat should penetrate 0.5–1 cm into the base for optimal sealing and bonding. Test a small section if needed.

⏺4. Signs of Proper Curing:

   - Surface appears dark and tacky (not wet or glossy).
   - No solvent or water remains on the surface.
   - The base feels firm and stable, with no loose particles.

⏺5. Post-Curing:

   - Inspect the surface for uniform coverage and adequate bonding before placing the asphalt layer.
   - Avoid delays beyond 48–72 hours after curing, as dust or debris accumulation may require re-cleaning the surface.

🏷Best Practices:

- Apply prime coat in dry, warm conditions (above 10°C) to ensure faster curing.
- For emulsions, lightly moisten the base course to aid penetration but avoid saturation.
- In hot climates, cutbacks like MC-70 cure faster but may require careful handling due to solvent volatility.
- In cooler or humid conditions, consider emulsions or adjust curing time expectations.

❇️Troubleshooting:

- Slow Curing: If curing takes too long, check for excessive application, high humidity, or low temperatures. Improve ventilation or wait longer.
- Poor Penetration: May indicate a dense base or insufficient material. Lightly scarify the base or adjust the application rate.
- Uneven Curing: Caused by inconsistent application. Recalibrate the distributor and ensure proper nozzle function.

@etconp

👉What Is Shear Wall

💫Shear wall is a structural member used to resist lateral forces i.e. parallel to the plane of the wall.

⏺For slender walls where the bending deformation is more, Shear wall resists the loads due to Cantilever Action.

⏺In other words, Shear walls are vertical elements of the horizontal force resisting system.

❇️In building construction, a rigid vertical diaphragm capable of transferring lateral forces from exterior walls, floors, and roofs to the ground foundation in a direction parallel to their planes.

🚧Examples are the reinforced-concrete wall.

⏺Lateral forces caused by wind, earthquake, and uneven settlement loads, in addition to the weight of structure and occupants, create powerful twisting (torsional) forces.

⏺This leads to the failure of the structures by shear.

❇️Shear walls are especially important in high-rise buildings subject to lateral wind and seismic forces.

⏺Generally, shear walls are either plane or flanged in section, while core walls consist of channel sections.

❇️They also provide adequate strength and stiffness to control lateral displacements.

⏺The shape and plan position of the shear wall influences the behavior of the structure considerably.

❇️Structurally, the best position for the shear walls is in the center of each half of the building.

⏺This is rarely practical, since it also utilizes the space a lot, so they are positioned at the ends.

❇️It is better to use walls with no openings in them. So, usually, the walls around lift shafts and stairwells are used. Also, walls on the sides of buildings that have no windows can be used.

@etconp

🚧 📣 Hey Construction Workers & Site Professionals! 🚧
📐 Want to level up your knowledge in surveying, site layout, GPS, and land work?

🏗️ Join the “Ethiopian Cadastral Surveyors” Channel!

This channel is built for YOU — the hardworking people behind every road, building, and boundary!

🛠️ Inside the Channel:
✔️ Easy-to-understand survey tips for site work
✔️ Layout & leveling tricks used by professionals
✔️ Tools & technology explained in simple language
✔️ Daily knowledge to boost your skill and confidence
✔️ Job vacancy updates and career tips

👷‍♂️ Whether you're a foreman, steel fixer, mason, or equipment operator — understanding surveying can make you faster, smarter, and more respected on site!

📲 Join now and grow your construction knowledge:
👉 t.me/Ethcadastralsurveyors

📤 Share with your team — let’s build Ethiopia with skill & precision! 🇪🇹🏗️

👉DESIGN PROCEDURES FOR A BUILDING FOUNDATION (STEP BY STEP)

1. DECIDE THE LOCATION OF COLUMNS & FOUNDATION AND TYPE OF LOADS ACTING ON THEM.(E.X DEAL LOAD,  LIVE LOAD OR WIND LOAD)

🚧On the building plan, the position of columns and load bearing walls should be marked, and any other induced loadings and bending moments.

🚧The loads should be classified into dead, imposed and wind loadings, giving the appropriate partial safety factors for these loads.

2. ESTIMATE ALLOWABLE BEARING PRESSURE OF SOIL USING GROUND INVESTIGATION REPORT.

🚧From a study of the site ground investigation (if available), the strength of the soil at various depths or strata below foundation level should be studied, to determine the safe bearing capacity at various levels.

🚧These values or presumed bearing values (from any standards or codes) in the absence of a site investigation are used to estimate the allowable bearing pressure.

3. DECIDE DEPTH OF FOUNDATION

🚧The invert level (underside) of the foundation is determined by either the minimum depth below ground level unaffected by temperature, moisture content variation or erosion this can be as low as 450 mm in granular soils but, depending on the site and ground conditions, can exceed 1 m or by the depth of basement, boiler house, service ducts or similar.

4. CALCULATE FOUNDATION AREA

🚧The foundation area required is determined from the characteristic (working) loads and estimated allowable pressure.

🚧This determines the preliminary design of the types or combination of types of foundation.

🚧The selection is usually based on economics, speed and buildability of construction.

5. DETERMINE VARIATION IN VERTICAL STRESSES

🚧The variation of vertical stress w.r.t depth is determined, to check for possible over-stressing of any underlying weak strata.

6. CALCULATE SETTLEMENT

🚧Settlement calculations should be carried out to check that the total and differential settlements are acceptable.

🚧If these are unacceptable then a revised allowable bearing pressure should be determined, and the foundation design amended to increase its area, or the foundations should be taken down to a deeper and stronger stratum.

7. COST CONTROL

🚧Before finalizing the choice of foundation type, the preliminary costing of alternative superstructure designs should be made, to determine the economics of increasing superstructure costs in order to reduce foundation costs.

8. CONSIDER TIME

🚧Alternative safe designs should be checked for economy, speed and simplicity of construction.

🚧Speed and economy can conflict in foundation construction an initial low cost solution may increase the construction period.

🚧Time is often of the essence for a client needing early return on capital investment.

🚧A fast-track programme for superstructure construction can be negated by slow foundation construction.

9. VARIATION IN GROUND CONDITION

🚧The design office should be prepared to amend the design, if excavation shows variation in ground conditions from those predicted from the site soil survey and investigation.

@etconp

ታምራት  ፕሌት እና ጄቦልት አቅራቢ

👉ከ አባይ ግድብ እስከ ኮሪደር ልማት

ከግለሰብ ቤቶች እስከ ተቋማት እና

መጋዘኖች በሁሉም የኢትዮጽያ ክፍል

አሻራችንን አሳርፈናል

🔰ምን ይፈልጋሉ?

✂️ላሜራ መቁረጫ ÷ ማጠፊያ እና መብሻ ማሽኖች አሉን

🔗ፌሮ (ቶንዲኖ) ጥርስ ማስበጀት ወይንም ማሳጠፍ ካሰቡ ለሱም ማሽኑ በጃችን ነዉ

📐ማንኛዉንም የሞደፊክ ስራዎችን የሚሰሩ ብቁ ባለሙያዎችም አሉን

☎️ይደዉሉልን ያማክሩን

📍ኢትዮጵያ ዉስጥ የትም እንልክሎታለን

አድራሻችን፦
                    ቁ.1 መርካቶ
                    ቁ.2 ተክለሀይማኖት
                     ቁ.3 አየር ጤና

0904040477
0994941708

👉መሰቦ ሲሚንቶ ፋብሪካ ማምረት ማቆሙ ተሰማ

💫በትግራይ ክልል ከሚገኙ ፋብሪካዎች ቀድሞ ወደ ሥራ ገብቶ የነበረው መሰቦ ሲሚንቶ ፋብሪካ፣ ከቦርድ አባላት አሰያየም ጋር በተፈጠረ አለመግባባትና በጥሬ ዕቃ አቅርቦት መቋረጥ ምክንያት ማምረት ማቆሙ ተሰማ፡፡  

በኤፈርት ሥር ከሚገኙ ትልልቅ ኩባንያዎች መካከል አንዱ የሆነው መሶቦ ሲሚንቶ ፋብሪካ፣ ማምረት ካቆመ ከሦስት ሳምንታት በላይ እንደሆነው የሪፖርተር ምንጮች ገልጸዋል፡፡

ፋብሪካው ሲሚንቶ ማምረት ያቆመበት ዋነኛ ምክንያት የተሰየሙ አዳዲስ የቦርድ አባላት ላይ ቅሬታ በመቅረቡና የደቡባዊ ዞን አስተዳደር ጥሬ ዕቃ እንዳይቀርብ በመከልከሉ እንደሆነ ከሪፖርተር ምንጮች ለመረዳት ተችሏል፡፡

‹‹ጥሬ ዕቃው ከእኛ እየተወሰደ ተጠቃሚ እየሆንን አይደለም፣ እንዲሁም እኛን የሚወክል ቦርድ ውስጥ አልተካተተም›› በሚል ምክንያት የተፈጠረው አለመግባባት፣ ፋብሪካውን ሥራ እስከ ማቆም አድርሶታል ተብሏል፡፡

📜ተጨማሪ ያንብቡ: https://ethiopianreporter.com/143157/

@etconp

👉የ Youtube ቻናል ጥቆማ

💫አዲስ ስለ ቴክኖሎጂ የከፈትነው ቻናል ነው Subscribe በማረግ አግዙን🙏👇

https://www.youtube.com/@WorldTechShow

👉In construction, the structure of a building refers to the load-bearing framework that supports the entire building and resists external forces like wind and seismic activity.

🏷It's essentially the skeleton that gives the building its shape, stability, and strength.

📜Here are the primary structures and components of a building in construction:

📌1. Foundation:

    *   Purpose: The lowest part of a building, which transfers the loads from the superstructure to the ground. It's crucial for preventing settlement and ensuring stability.
    *   Types:
        *   Shallow Foundations: Footings (isolated, combined, strip), rafts/mats.
        *   Deep Foundations: Piles (bored, driven), piers, caissons.

📌2. Super structure: This is the part of the building above the ground level, comprising several key elements:

    *   Columns:
        *   Purpose: Vertical structural members that transmit compressive loads from beams, slabs, and walls above down to the foundation.
        *   Materials: Typically reinforced concrete, steel, or timber.

    *   Beams:
        *   Purpose: Horizontal structural members that support vertical loads (from slabs, walls) and transfer them horizontally to columns or other supports. They resist bending moments and shear forces.
        *   Types: Reinforced concrete beams, steel beams, composite beams, timber beams.

    *   Slabs:
        *   Purpose: Flat, horizontal structural elements that form floors and roofs. They directly support distributed loads (people, furniture, equipment) and transfer them to beams or columns.
        *   Types: One-way slabs, two-way slabs, flat plates, flat slabs, ribbed/waffle slabs.

    *   Walls:
        *   Purpose: Can be load-bearing (supporting roofs, floors, and other walls) or non-load-bearing (partitioning space, enclosing the building).
        *   Types: Masonry walls (brick, block), reinforced concrete walls, shear walls (designed to resist lateral forces like wind and earthquakes).

    *   Roof:
        *   Purpose: The uppermost covering of a building, providing protection from weather elements and contributing to the overall structural integrity.
        *   Types: Flat roofs, pitched roofs (gable, hip, shed), shell roofs, dome roofs. The structural elements of a roof can include rafters, trusses, purlins, and decking.

📌3. Lateral Load Resisting Systems:

    *   Purpose: These systems are specifically designed to resist horizontal forces like wind pressure and seismic (earthquake) loads, which can cause swaying or collapse.
    *   Components: Shear walls, braced frames (X-bracing, K-bracing, V-bracing), moment-resisting frames (rigid connections between beams and columns), and sometimes core walls around elevators or stairwells.

📌4. Framing Systems:

    *   Buildings are often constructed using different framing systems that define how loads are distributed. Common types include:
        *   Skeletal/Frame Structure: Consists of a framework of columns and beams, with walls acting as infill. Most common for multi-story buildings.
        *   Load-Bearing Wall Structure: Walls directly support the floors and roof. More common for simpler, lower-rise buildings.
        *   Shell Structures: Thin, curved structures (domes, vaults) that gain strength from their geometry.

📐These structural components, when designed and constructed correctly, ensure the safety, stability, and durability of a building.

@etconp

#ADVERTISEMENT

📌 Motivation + Learning

🏗️ Skilled Hands Deserve Sharp Minds
Are you working on a construction site but want to learn more about how things are measured, marked, and managed?
📐 Join Ethiopian Cadastral Surveyors
— the smart channel for construction professionals who want to grow.
🔥 Here’s what’s inside:
🔧 Surveying tips made easy
📏 Layout tricks explained in Amharic & English
🗺️ Site tools, GPS, and total station basics
🧰 On-site experience shared by real professionals
🌟 This is not a classroom — it's a practical space to learn and level up, even while you're working!
📲 Join the team of knowledge-driven builders:
👉 t.me/Ethcadastralsurveyors

🙌 Knowledge is power – on site and in life.

👉In building construction, the terms Substructure and Superstructure refer to the two primary divisions of a building, separated by the ground level or plinth level.

❇️Understanding these two components is crucial for comprehending how a building stands, functions, and withstands various forces.

📚 Substructure (Foundation System)

⏺The substructure, often referred to as the foundation, is the part of the building that is constructed below the ground level.

⏺It acts as the backbone of the entire structure, responsible for safely transferring the loads from the superstructure to the underlying soil or rock strata.

🎲Key Characteristics and Functions:

⏺1. Load Transfer: Its primary function is to transfer the entire load of the building (dead loads, live loads, wind loads, seismic loads, etc.) safely and uniformly to the supporting soil without causing excessive settlement or failure.
⏺2. Stability: It provides stability against overturning, sliding, and differential settlement, ensuring the building remains upright and intact.
⏺3. Protection: It protects the building from ground-related issues like moisture penetration, ground movements (e.g., due to expansive soils or seismic activity), and frost heave.
⏺4. Base for Superstructure: It forms a solid and level base upon which the superstructure is built.

📜Main Components of Substructure:

⭐️Foundation Footings: These are the lowest part of the substructure, typically wider than the walls or columns they support, designed to distribute the load over a larger area of soil, reducing the stress on the ground.

🏷Common types include:

    *   Isolated Footings: For individual columns.

    *   Combined Footings: For two or more columns close together.

    *   Wall Footings (Strip Footings): For continuous load-bearing walls.

    *   Raft/Mat Foundations: A large concrete slab covering the entire footprint of the building, used when soil bearing capacity is low or column loads are very high.

*   Piles: Used when suitable bearing strata are very deep. Piles are long, slender elements driven or cast into the ground to transfer loads to stronger soil layers or to resist uplift forces.

*   Plinth Beam / Grade Beam:

⏺This is a reinforced concrete beam constructed at or slightly above the ground level (often at the DPC level).
⏺It connects the column foundations, helping to distribute the load evenly and acting as a tie beam.
⏺It also provides a base for the walls of the superstructure and prevents dampness from rising from the ground into the walls above.

*   Basement Walls: If the building has a basement, the retaining walls that enclose the basement space below ground level are considered part of the substructure.

*   Damp Proof Course (DPC):

⏺A layer of waterproof material (like a rich cement concrete mix, bitumen, or plastic sheets) laid horizontally at the plinth level to prevent moisture from rising from the ground into the walls of the superstructure due to capillary action.

🚧Importance of Substructure:

⏺A well-designed and constructed substructure is paramount.

⏺Any failure or inadequacy in the foundation can lead to severe structural damage, including cracks in walls, differential settlement, or even collapse of the entire building.

⏺The design of the substructure heavily depends on soil conditions (geotechnical investigation), the type of building, and the loads it will bear.

@etconp

👉 በኢትዮጵያ ኮንስትራክሽን ባለስልጣን ቀደም ሲል ይሰጡ የነበሩ የምዝገባና ሰርተፍኬሽን አገልግሎቶች መካከል አስር ያህሉ  ወደ መሶብ የአንድ ማዕከል አገልግሎት ተዘዋውረዋል፡፡

❇️መንግስት ለዜጎች የሚሰጣቸው አገልግሎቶችን ለማሳለጥ የሪፎርም ስራዎችን አያካሄደ ይገኛል፡፡

🎲የበለጸገች ኢትዮጵያን ለመገንባት ጥራት ያለውና የዜጎችን ርካታ ከፍ የሚያደርግ የሲቪል ሰርቪስ አገልግሎትን በክህሎት፣ በቴክኖሎጂ  እና በመልካም አስተዳደር  የማዘመን ተግባር እየተከናወነ ነው፡፡

⏺ይህንን እውን በማድረግ ፈር ቀዳጅ የሆነውን  የመሶብ አገልግሎት ማዕከል በቅርቡ ስራ ማስጀመሩም ይታወቃል፡፡

⏺በ 23 ተቋማትና 124 የአገልግሎት አይነቶች በአንድ ማዕከል መሰጠት የጀመረው የመሶብ  አንድ ማዕከል አገልግሎት በቴክኖሎጂ በመታገዝ የተገልጋዮችን ጊዜ፣ ገንዘብ እና ጉልበትን በሚቆጥብ መልኩ ፈጣንና እርካታን ያላበሰ አገልግሎት እየተሰጠ ይገኛል።

⏺በዚሁ መሰረትም የኢትዮጵያ ኮንስትራክሽን ባለስልጣን ከ23ቱ ተቋማት አንዱ በመሆን ከሚሰጣቸው አገልግሎቶች ውስጥ አስር የአገልግሎት አይነቶችን በመሶብ አንድ ማዕከል እየሰጠ ይገኛል፡፡

🎲በዚሁ መሰረት ቀደም ሲል በኢትዮጵያ ኮንስትራክሽን ባለስልጣን ይሰጡ የነበሩና ወደ መሶብ አንድ ማዕከል የተዛወሩ የምዝገባና ሰርተፍኬሽን አገልግሎቶች ከዚህ በታች የተዘረዘሩት ናቸው፡፡

⭐️አዲስ የባለሙያ ምዝገባና አገልግሎት

1.  የባለሙያ ምዝገባ የእድሳት አገልግሎት
2.  የባለሙያ የጠፋ የሙያ ፈቃድ መተካት 
3.  አዲስ የዉሃ ነክ ባለሙያ  ፈቃድ ምዝገባ
4.  እድሳት የውሀ የዉሃ ነክ ባለሙያ  ፈቃድ ምዝገባ
5.  የጠፋ የውሃ ባለሙያ ፈቃድ መተካት
6.  የውሃ ባለሙያ ፈቃድ ደረጃ ዕድገት
7.  አዲስ የውሃ ስራዎች ካምፓኒ የምዝገባና ብቃት ሰርተፍኬት
8.  የውሃ ስራዎች ካምፓኒ ብቃት ሰርተፍኬት ዕድሳት
9.  የውሃ ስራዎች ካምፓኒ ሰርተፍኬት የደረጃ ለውጥ ናቸው፡፡

🚧ክቡራን ተገልጋዮችም እነዚህ አገልግሎቶች ከተቋማችን ወደ መሶብ አንድ ማዕከል መዛወራቸውን በማወቅ የአገልግሎቱ ተጠቃሚ እንዲሆኑና ወደ ተቋማችን በመምጣት እንደይጉላሉ ከወዲሁ እናሳውቃለን፡፡

💫የኢትዮጵያ ኮንስትራክሽን ባለስልጣን

@etconp