👉Construction Sequence of a Building – Step by Step

1. Site Preparation: Clear vegetation, mark layout, and level site.

2. Excavation: Excavate to required depth for foundation.

3. Foundation: Place footing, concrete, and reinforcement as per design.

4. Plinth Beam: Cast plinth beam and fill up to floor level.

5. Superstructure: Construct columns, beams, and slabs (RCC work).

6. Brickwork: Build walls between columns for rooms and partitions.

7. Lintel & Roof: Cast lintel and roof slab; apply waterproofing.

8. Plastering: Apply internal and external plaster for smooth surface.

9. Flooring: Lay tiles, marble, or granite flooring.

10. Doors & Windows: Fix frames and shutters properly.

11. Electrical & Plumbing: Install wiring, piping, and fixtures.

12. Painting & Finishing: Paint walls, install fittings and polish surfaces.

13. Final Inspection: Quality check and handover to owner.

#CivilEngineering #BuildingConstruction #SiteWork #constructionsite #constructionsequence #Civil

https://t.me/ETCONpWORK

@etconp

👉WHAT ARE PURPOSE OF REINFORCEMENT RIBS?

🚧These ribs are intentionally formed during manufacturing to improve the bond between the steel reinforcement and the surrounding concrete.

💫Those are ribs (deformations) on the reinforcement bar, designed to enhance bond and prevent slippage in reinforced concrete.

#ConstructionInsights #ReinforcementBars #CivilEngineering #StructuralDesign #ConcreteTechnology #SiteKnowledge #BuildingConstruction #EngineeringEducation #ConstructionQAQC #RebarDetails #StructuralIntegrity #ConcreteBond #ConstructionMaterials

@etconp

👉የ Building Construction ኮሌጅ የመጀመሪያዎቹ ምሩቃን ህዳር 1952 ዓ.ም

💫የተያያዙት ምስሎች በአዲስ አበባ ህንፃ ኮሌጅ ምረቃ ላይ የተነሱ ናቸው።

⏺ዋና እንግዶች ንጉሠ ነገሥት ቀዳማዊ  ኃይለ ሥላሴ እና ልዑል በርትል ከስዊድን ነበሩ።

🏷በዚህ ቀን በህዳር 1952 ዓም (November 1959) የመጀመሪያ  ተማሪዎች ዲግሪያቸውን አግኝተዋል።

⏺ይህ ተቋም በ1954 እኤአ የተመሰረተው በኢትዮጵያ እና በስዊድን መንግስታት መካከል በተደረገው የሁለትዮሽ ስምምነት ነው።

⏺እ.ኤ.አ. በ 1955 የተጀመረው የመጀመሪያ የትምህርት መርሃ ግብር በህንፃ ኢንጂነሪንግ ውስጥ የሶስት ዓመት የዲፕሎማ መርሃ ግብር ለመስጠት ነበር።

⏺በ እ.ኤ.አ. 1957/58 የትምህርት ዘመን ማጠናቀቂያ ላይ ስልጠናው ወደ አራት አመት መርሃ ግብር በማደግ በ Bsc በ ህንፃ ምህንድስና ዲግሪ መስጠት ጀመረ።

https://www.flickr.com/photos/73738739@N03/albums/72157628794132559/

Via አብዱል አዚዝ

@etconp

👉UNDERSTANDING ROAD LAYERS

💫Every strong and durable road you drive on rests on a powerful structure beneath, not just asphalt!

🏷Here’s the breakdown

1. Pavement (Surface Layer):
This is the visible top layer made of asphalt or concrete providing a smooth, safe, and waterproof surface for vehicles.

2. Base Course:
The load distributor! It transfers traffic loads from the surface to the lower layers. Usually made of crushed stones or gravel.

3. Sub-base:
Acts as a cushion and improves drainage. It reduces stress on the subgrade and prevents pumping of fine materials.

4. Subgrade:
The foundation of the entire pavement system made up of compacted natural soil. Its strength and stability determine the performance of the whole road.

#RoadConstruction #CivilEngineering #PavementDesign #GeotechnicalEngineering #InfrastructureDevelopment #ConstructionInsights #EngineeringEducation

@etconp

ADVERTISMENT

ታምራት ፕሌት እና ጄ ቦልት አቅራቢ

✅የምንሰጣቸው አገልግሎቶች

🔅 ፕሌት any Size & thickness
🔅 ጄ ቦልት (ጥርስ ማዉጣትና ማጠፍ)

🔅 የተለያዩ  [modefic] ስራዎችን እንሰራለን።

♦️ ማንኛዉንም ብረታ ብረት እንገዛለን።

☎️ስልክ 0904040477 ወይም 0911016833 ደውለው ያግኙን
📱ቴሌግራም ላይ ፦https://t.me/heavenic1

አድራሻ፦  ቁ 1.መርካቶ
                ቁ.2 አየር ጤና  ኪዳነ ምህረት

ጥራትና ታማኝነት መለያችን ነው።
ታምራት ፕሌት እና ጄ ቦልት አቅራቢ

👉Deflection Control in Beams and Slabs

1. Causes of Deflection

• Excessive load on the member.
• Inadequate stiffness or reinforcement.
• Creep and shrinkage in concrete.
• Long span or insufficient depth.

2. Permissible Deflection Limits (According to Codes)

• Span/250 for total deflection under all loads.
• Span/350 or 20 mm for deflection after finishes are applied.
• Codes like ACI, IS 456, and Eurocode specify these limits.

3. Methods of Deflection Control

• Increase the depth of the beam or slab.
• Provide adequate reinforcement.
• Use higher-grade concrete to reduce creep.
• Limit span-to-depth ratio.
• Provide prestressing in long spans.

4. Span-to-Depth Ratios (General Guidelines)

• Simply Supported Beam – 20
• Continuous Beam – 26
• Cantilever Beam – 7

https://youtube.com/@ethiopianconstruction?si=YPBAC3MRTl5Uu6BK

@etconp

👉Airport Runway Design Basics

1. Introduction

Runway design is a crucial part of airport planning, ensuring safe aircraft take-off
and landing. Proper design considers aircraft type, load, weather, and localgeography.

2. Runway Orientation

Orientation is based on prevailing wind direction to minimize crosswindcomponents. Wind analysis for at least 10 years is preferred.

3. Runway Length

Length depends on aircraft type, elevation, temperature, and gradient. Higherelevation and temperature require longer runways.

4. Runway Width

Width varies depending on aircraft class. For example, Code E aircraft require aminimum width of 45 meters.

5. Runway Gradient

The longitudinal gradient should not exceed 1.5%. Transverse gradient ensuresproper drainage, typically 1.5% to 2%

6. Runway Surface

Common materials include flexible pavements (asphalt) and rigid pavements(concrete). The surface must be smooth, durable, and well-drained.

7. Runway Markings and Lighting

Runway markings include threshold, centerline, and touchdown zone markings.

Lighting helps in low visibility—types include edge lights, approach lights, andcenterline lights.

8. Runway Safety Areas

Runway End Safety Area (RESA) is provided beyond the end of the runway strip tominimize damage in case of overrun or undershoot.

9. Drainage and Maintenance

Proper drainage is essential to avoid standing water. Regular maintenanceensures surface integrity and friction.

10. Conclusion

A well-designed runway ensures efficient and safe airport operation, supportingboth current and future aviation needs.

@etconp