👉Possible Reasons for Removing Column Formwork at 8 Hours

💫1. Rapid-Hardening (High Early Strength) Concrete Was Used

⏺If the contractor used rapid-hardening cement (RHC) or an accelerator admixture, the concrete can gain enough strength in 6–8 hours to allow formwork removal.

🏷Example:

⏺Quick setting concrete
⏺Concrete with calcium nitrate/calcium chloride accelerators
⏺Special high-early-strength mix

💫2. Very High Temperature Curing Conditions

⏺In hot climates, concrete gains strength faster.
⏺If the temperature is 30–35°C+, the surface concrete may harden quicker, sometimes allowing earlier removal.

💫3. Contractor Working Under Time Pressure or Poor Planning

⏺Sometimes the contractor removes formwork early to:

*reuse formwork
*push schedule
*continue work above

⏺This is not a valid technical reason and is risky.

💫4. Very Light Formwork (Only Side Panels)

⏺For columns, removing only the side panels earlier is possible because the column carries no load from above at this stage.

⏺But 8 hours is still too early unless concrete strength is verified.

❌ Why It Is Usually NOT Allowed

⏺Removing formwork at 8 hours may cause:

*surface damage / honeycombing
*corners chipping
*loss of shape
*structural weakness if strength is too low

⏺Concrete normally needs: 5–7 MPa minimum strength before column formwork removal
⏺Usually achieved at 24 hours, not 8.

✅ Correct Professional Answer

🚧Formwork removal at 8 hours is only acceptable if the concrete is high-early-strength or contains an accelerator and if strength has been verified.

⏺Otherwise, it is not recommended and can damage the column.

@etconp

ደረጃቸውን የጠበቁ እብነበረድ እና ግራናይቶች!

ለቤትዎ ወይም ለንግድ ተቋምዎ ግንባታ ተስማሚ የሆኑ፣ ከፍተኛ ጥራት ያላቸውን እና ጠንካራ የእብነበረድ እና ግራናይት ውጤቶችን እናቀርባለን።

Lime stone
Babile Granite
Axum Granite

👉 አዳዲስ የገቡ ምርቶችን፣ ወቅታዊ መረጃዎችን እና ልዩ ቅናሾችን ለማግኘት የቴሌግራም ቻናላችንን ይቀላቀሉ!

@wollegastones
@wollegastones

👉If Ready-Mix Concrete (RMC) has already started to set while pouring, you must be very careful.

💫The correct action depends on how far setting has progressed.

✅ If concrete is only losing workability (early stiffening)

🚧You can add a compatibility-approved chemical admixture such as:

⭐️1. Superplasticizer / High Range Water Reducer (HRWR)

⏺Restores workability without adding water
⏺Maintains strength and durability

🏷Common types:

*Polycarboxylate Ether (PCE)
*Naphthalene-based

✅ This is the best and safest option when setting has just started.

💫2. Retarding Admixture (only if approved by mix designer)

⏺Slows down further setting
⏺Useful in hot weather or long transport time

❌ What NOT to do

⏺Do NOT add water indiscriminately → reduces strength & causes segregation
⏺Do NOT remix concrete that has begun hard setting or initial set
⏺Do NOT add cement on site

🚨 If concrete has reached initial set

⏺DO NOT try to re-temper
⏺Reject the batch
⏺Remove and replace

✅ Practical Site Action Steps

⏺1. Check concrete temperature & slump
⏺2. If slump is low but still plastic → add approved superplasticizer as per supplier dosage
⏺3. Remix truck for 30–60 revolutions
⏺4. Re-test slump before placing

📍Typical Dosage (Guide only)

⏺Super plasticizer: 0.8 – 1.5% of cement weight (Exact dosage must follow supplier data sheet)

@etconp

👉What is HVAC in Electrical instalation?

💫HVAC = Heating, Ventilation and Air Conditioning.

🚧HVAC Services include:

🏷1. Heating systems

⏺Design and installation of boilers / heat pumps
⏺Installation of radiators, fan coil units
⏺Operation & maintenance of heating system
⏺Troubleshooting heat loss, balancing

🏷2. Ventilation systems

⏺Fresh air duct design and installation
⏺Exhaust systems (kitchen, toilet, basements, car parks)
⏺Smoke control ventilation (stair pressurization, smoke extraction)
⏺Air filtration systems
⏺Periodic cleaning of ducts & filters

🏷3. Air conditioning systems

⏺Split AC installation, testing and commissioning
⏺VRF/VRV system supply & installation
⏺Chilled water system installation (chillers, AHUs, FCUs)
⏺Cooling tower checking and servicing

🏷4. Controls & automation

⏺BMS integration for HVAC
⏺Thermostat installation
⏺Sensors and actuators calibration

🏷5. Preventive maintenance services

⏺Gas leak detection
⏺Filter cleaning and replacement
⏺Coil and duct cleaning
⏺Refrigerant charge checking
⏺Electrical connection tightening

🏷6. Energy efficiency improvement

⏺Energy audit and energy saving recommendations
⏺Optimization of equipment operation
⏺Upgrading equipment to high efficiency systems

@etconp

👉Main Types of Drawings in Road Projects

🏷1) Construction Drawings (Working Drawings)

⏺These are the drawings the contractor uses to actually build the road.

🔰They usually include:

• Road alignment plan
• Profile (longitudinal section)
• Cross-sections
• Pavement structure details
• Drainage layout
• Culverts/bridges details
• Quantities and dimensions
• Material specifications

📍Purpose:

⏺Give full instructions for execution on site.

🏷2) Typical Drawings

⏺Standardized sketches used repeatedly along the project.

🔰Examples:

• Typical road cross-section
• Typical shoulder detail
• Standard pavement layer compositions
• Standard culvert inlet/outlet
• Standard ditch profile
• Guardrail installation typical
• Pavement marking typical layouts

📍Purpose:

⏺Avoid redrawing the same details everywhere; ensures uniform design.

🏷3) Alignment Drawings (Plan View)

⏺Shows the horizontal layout of the road.

📍Includes:

• Centerline
• Curves and radii
• Stations (chainage)
• Road width
• Intersections
• Right-of-way

📍Purpose:
Defines the exact path/location of the road.

🏷4) Longitudinal Profile (L-Section)

⏺A vertical view along the centerline.

📍Shows:

• Existing ground level
• Proposed finished road level
• Grades (slopes)
• Vertical curves
• Drainage flow direction

📍Purpose:

⏺Controls the vertical geometry of the road.

🏷5) Cross-Section Drawings

⏺Perpendicular cut at intervals (e.g., every 20m).

📍Includes:

• Road layers
• Embankment/cut details
• Side slopes
• Drainage channels
• Ditches
• Berms
• Service ducts if any

📍Purpose:

⏺Shows earthwork, widths, and pavement layers at each station.

🏷6) Pavement Design Drawings

⏺Focused on the pavement structure.

📍Shows:

• Subgrade level
• Sub-base
• Base course
• Asphalt layers
• Material specifications

📍Purpose:

⏺Defines pavement thickness and materials based on design traffic + soil.

🏷7) Structure Drawings (For Bridges & Culverts)

📍Includes:
• Box culverts
• Pipe culverts
• Retaining walls
• Bridges (abutments, piers, deck, girders)
• Expansion joints
• Reinforcement details

📍Purpose:
All drawings related to specific structures along the road.

🏷8.  Drainage Drawings

⏺Used to manage stormwater.

📍Shows:
• Side ditches
• Catch basins
• Stormwater pipes
• Channels
• Culvert sizes/locations
• Energy dissipators

📍Purpose:
Prevent flooding and protect the pavement.

🏷9) Traffic Control & Road Safety Drawings

📍Includes:
• Road signs
• Pavement markings
• Guardrails
• Speed bumps
• Traffic islands
• Signal layout (if any)

📍Purpose:
Ensures safety and regulates traffic.


🏷10) Utility Relocation Drawings

⏺Shows existing and proposed utility lines.

📍Includes:
• Water lines
• Electric cables
• Telecom ducts
• Sewer lines
• Gas lines (if applicable)

📍Purpose:
Coordinate with utility agencies and avoid conflicts during construction.


🏷11) Quantity & Earthwork Drawings

⏺Used for measurement and BOQ.

📍Shows:
• Cut and fill diagrams
• Earthwork volumes
• Borrow pit & spoil locations

📍Purpose:
⏺Supports cost estimation and progress payment.

📚 12) As-Built Drawings

⏺Prepared after construction.

📍Shows:
• Actual constructed dimensions
• Field changes
• Final alignment & profile
• Final structures & drainage
• Updated utility routes

📍Purpose:
⏺Official record for future maintenance and upgrades.

@etconp

👉Epoxy Flooring for Warehouse – Overview & Guidance

💫Epoxy flooring is one of the best solutions for warehouses due to its strength, durability, and easy maintenance.

✅ Key Benefits

High durability: Resists heavy forklift traffic and impact loads

Chemical resistance: Withstands oil, fuel, acids, and solvents

Dust-free surface: Seals concrete and prevents powdering

Easy to clean: Smooth, seamless finish

Improved safety: Can include anti-slip texture and line markings

Bright finish: Reflects light and improves visibility

🧱 Common Types for Warehouses

1. Self-Leveling Epoxy

Smooth and seamless

Ideal for high-traffic areas

2. Epoxy Mortar Flooring

Extremely strong

Best for very heavy loads and industrial zones

3. Quartz-Filled Epoxy

Decorative and slip-resistant

Suitable for wet areas

4. Anti-Static Epoxy

For electronic or sensitive storage areas

📏 Typical System Build-Up

Concrete surface grinding / shot blasting

Primer coat

Epoxy body coat (2–3 mm standard, up to 5 mm for heavy duty)

Top coat (UV resistant or anti-slip if required)

💰 Thickness Guide

Usage Type Recommended Thickness

Light duty 1–2 mm
Medium duty 2–3 mm
Heavy duty (forklifts) 3–5 mm

⚠️ Important Installation Considerations

Concrete moisture content must be below 5%

Surface must be clean, crack-free, and well cured (min. 28 days)

Proper ventilation during application

Temperature range: 10°C – 35°C

🕒 Curing Time

Light foot traffic: 24 hours

Full traffic: 5–7 days

@etconp

👉What problems occur in the higher grade of concrete mix design?

💫Higher grades of concrete mix design, such as those with a compressive strength of 40 MPa (megapascals) and above, can present several challenges.

🚧Here are some common problems associated with high-grade concrete:

1. Workability Issues
Reduced Workability: Higher strength concrete typically has lower water content, which can make it more difficult to mix, place, and finish.
Need for Admixtures: To improve workability, chemical admixtures like superplasticizers may be necessary, which can complicate the mix design.

2. Segregation and Bleeding
Segregation: The use of lower water-to-cement ratios can lead to segregation of aggregates, especially in highly fluid mixes.
Bleeding: Higher grades may also experience bleeding, where excess water rises to the surface, potentially affecting the surface finish.

3. Curing Challenges
Curing Requirements: Higher-grade concrete requires careful curing to achieve desired strength. Insufficient curing can lead to cracking and reduced durability.
Temperature Sensitivity: High-strength mixes are sensitive to temperature variations during curing, which can affect hydration and strength development.

4. Shrinkage and Cracking
Higher Shrinkage: The lower water content can lead to increased shrinkage, resulting in cracking, especially in large pours.

Thermal Cracking: Rapid temperature changes during curing can also cause thermal cracking, necessitating temperature control measures.

5. Cost Implications
Material Costs: Higher-grade concrete often requires more expensive materials, such as higher-quality aggregates and supplementary cementitious materials (SCMs), increasing overall costs.
Labor Costs: The need for skilled labor to handle and place the concrete effectively can also add to project expenses.

6. Durability Considerations
Permeability Issues: While higher grades can be more durable, they may also be more susceptible to permeability issues if not designed correctly, leading to potential durability problems over time.
Long-Term Performance: Ensuring that the concrete maintains its strength and durability over its service life requires careful selection of materials and mix design.

7. Mix Design Complexity
Complexity in Design: Designing a high-strength mix requires a thorough understanding of materials and their interactions, making the mix design process more complex.
Testing Requirements: More rigorous testing and quality control measures are often needed to ensure that the mix meets the desired specifications.

🏷Conclusion

⏺Overall, while high-grade concrete offers advantages in strength and performance, it also presents several challenges that must be carefully managed through appropriate mix design, material selection, and construction practices.

@etconp

👉የምስራች ዜና ለዚህ ቻናል ቤተሰቦች

💫ለ ስኮላር ሺፕ አመልካቾች

⏺CV EURO PASS እና Motivational Letter እናዘጋጃለን
⏺PASSPORT APPOINTMENT (ፓስፖርት ቀጠሮ) እንይዛለን
⏺የተለያዩ የ ስኮላሽፕ ዕድሎች ማማከር

📞በተመጣጣኝ ዋጋ በ +251902024749 አግኙን🙏

@etconp

🇪🇺🇩🇪 Germany & other European countries!

🧑‍💻 Hospitality, Logistics & Construction sector workers are needed!

🌍 Open for: India, Bangladesh, Philippines, Ghana, Nigeria, South Africa, Ethiopia & others.

📑 Fast process time!
✅ Full company support + accommodation agreement

✈️ Start your journey to Europe today!

Telegram: Europe Work Visa
Check the offer here! ⬆️

ታምራት  ፕሌት እና ጄቦልት አቅራቢ

♧ ሁሉን በአንድ ቦታ ለሁሉም ቅርብ

📍ኢትዮጵያ ዉስጥ የትም እንልክሎታለን

♧ ይደውሉልን ያማክሩን

0904040477
0911016833

👉 INTERCON Construction Chemicals 

● Concrete Admixtures
● Bonding Agents
● Waterproofings
● Wall Putty, Prime Coat
● Concrete Repair Mortar
● Floor hardener, Epoxy
● Grout, Self-level mortar
● Quartz paint, Contextra
● Tile Adhesive & Tile Joint Fillers 
● Geotextiles and other construction chemicals and materials

☎️ Tel: 0961955555

🔹 Address 1: Signal road, around
Dinberwa Hospital

🔹 Addres 2: Wellosefer, Infront of
Dani Plaza

👉What Is Fly Ash

💫Fly Ash is a fine powder that comes from burning pulverized coal in power plants.
⏺It is a by-product collected from the flue gases.
⏺In construction, it is used as a supplementary cementitious material (SCM) — meaning it behaves like cement when mixed with water.

✅ What Fly Ash Does

⏺Fly ash contains silica (SiO₂) and alumina (Al₂O₃) that react with the lime (Ca(OH)₂) released from cement hydration and form additional calcium silicate hydrate (C-S-H) — the main strength-giving compound of concrete.

⭐ Importance of Fly Ash in Concrete

1️⃣ Improves Workability

⏺Fly ash particles are spherical and smooth → they act like tiny ball bearings, making fresh concrete easier to mix and place.
2️⃣ Increases Long-Term Strength

⏺The pozzolanic reaction continues for a long time and forms extra C-S-H → results in higher strength after 28 days and beyond.

3️⃣ Reduces Heat of Hydration

⏺Good for mass concrete (dams, thick foundations) because it minimizes temperature cracks.

4️⃣ Improves Durability

⏺Fly ash concrete is more resistant to:
Sulphate attack
Chloride penetration
Alkali-silica reaction (ASR)
Permeability (less water enters)

5️⃣ Reduces Cement Consumption

⏺Replacing 15–30% of cement with fly ash:
Saves cost
Makes concrete more sustainable
Reduces CO₂ emissions

6️⃣ Increases Workability Retention

⏺Slower setting → useful for hot weather concreting.

7️⃣ Improves Finish

⏺Makes surface smoother and reduces bleeding & segregation.

⚠️ Disadvantages (for full understanding)

❇️Slower early strength (first 3–7 days) compared to pure cement.

❇️Not suitable in very cold weather without special care.
Quality depends on source; low-quality fly ash reduces benefits.

🎯 Simple Definition

⏺Fly ash is a cement-like powder from coal power plants used in concrete to improve strength, durability, workability, and reduce cost.

@etconp

👉Claim on Additional floor Construction/Addition Works/:

🚧A contractor can generally claim for an additional floor construction requested by the client, but it depends on the contract agreement and the change management procedures in place.

🏷How it usually works?

1. Check the Original Contract

If the signed contract was for G+8, and now the client wants to extend to G+10, this is outside the original scope.

The contractor is not obligated to do it without a variation order (VO) or new contract agreement.

2. Variation / Change Order

Most contracts (FIDIC, PPA Ethiopia 2011, etc.) have clauses for variations.

The client (or Engineer/Consultant) issues a variation instruction in writing.

The contractor then submits a claim for:

Additional costs (materials, labor, equipment, subcontractors).

Time extension (because adding two floors increases duration).

3. Contractor’s Right to Claim

The contractor can claim if:

The client formally instructs the change.

The change affects cost and time.

Contractor must submit the claim within the time frame stated in the contract (often 28 days in FIDIC).

4. Evaluation and Approval

The Engineer/Consultant or Client evaluates the claim.

Once approved, the contract price and completion date are adjusted.

5. Risks if No Formal Agreement

If the contractor builds extra floors without written approval, payment disputes may arise.

The client may later refuse to pay, claiming it was not properly instructed.

In summary:
The contractor has the right to claim for additional floor construction requested by the client, but it must go through the formal variation/change order process, with clear documentation of cost and time impact.

@etconp

👉Load Distribution Two Way Slab To Beam

💫A two-way slab carries load in both directions (toward beams on all four sides) when the slab aspect ratio (longer side ÷ shorter side) is not large (rough rule: between about 0.5 and 2.0).

📌The slab load is transferred to beams as line loads (kN/m) — think of the slab as many narrow strips that hand their load down to the beams beneath them.

📌Common practical methods to determine the load carried by a particular beam:

🏷1. Tributary-area method (simple, conservative): each beam takes the load from the slab area that is closest to it.

🏷2. Equivalent strip / direct design method (used in code handbooks: ACI, BS, IS/BIS) — account for two-way action and give moment distribution coefficients.

🏷3. FE / plate analysis (most accurate) — used for complex geometry, openings, irregular supports.

@etconp

#ADVERTISEMENT

የSEO እና Google Business Profile ማስተዋወቂያ መግለጫ – ለConstruction ድርጅቶች

የግንባታ ኩባንያዎ Google ላይ ይታያል፣ ይታመናል፣ ይመረጣል! በተጠናከረ የSEO ብቃት እና በተቀናጀ የGoogle Business Profile አስተካክለን ኩባንያዎን በConstruction ገበያ ውስጥ ማየት የሚችሉት ደንበኞች ቁጥር በእጅግ ይጨምራል።

⭐ የSEO (Search Engine Optimization) ጥቅሞች
• ኩባንያዎ በGoogle መመሪያ ገፅ ላይ በመጀመሪያ ላይ እንዲታይ ያግዛል
• “Construction company in Addis Ababa” ያሉ ቁልፍ ቃላት ላይ ውስጥ ይመደባል
• የደንበኞች እይታ እና የትዕዛዝ መጥራት ይጨምራል

⭐ የGoogle Business Profile (GBP) ጥቅሞች
• ኩባንያዎ በGoogle Maps እና በGoogle Search ውስጥ በቀላሉ ይታያል
• ስልክ ቁጥር፣ አድራሻ፣ የስራ ሰዓት፣ ፎቶዎች እና አገልግሎቶች በሙሉ እንዲታዩ ያደርጋል
• ደንበኞች በቀጥታ ለመደወል፣ መልዕክት መላክ ይችላሉ
• በስራዎ ላይ የተሰጡ ግምገማዎች እና ኮመንቶች ያሳያል
• የተሻለ የአካባቢ ገበያ (Local SEO) ትርፍ ያመጣል

ይሄንን ሁሉ
በ 2,000 ብር ብቻ 🔥

@BemiCreatives

0902397727