#ADVERTISEMENT

INTRODUCE A CUSTOMER. EARN A COMMISSION!

ደንበኛ ያስተዋውቁ፣ ኮሚሽን ያግኙ!

WELCOME TO SUNSPACE FINISHING MATERIALS!

✨ BETTER QUALITY. LOWER PRICES.
✨ የተሻለ ጥራት፣ በተሻለ ዋጋ!

✨ OUR PRODUCTS | የምርት ዓይነቶቻችን

🛁 Bathroom Solutions (WC Set, Shower Panel, Heaters & Accessories)

✨ Ceramics and Porcelain

🔧 PPR Pipes & Fittings

🏠 Granite (Staircase & Kitchen Tops)

💧 Construction Chemicals & Waterproofing Products

📍 VISIT US: Signal Shopping Centre, 1st Floor.

📞 CALL US: 09 11 51 87 40

🤝 SUNSPACE TRADING — LET’S GROW TOGETHER!

#finishing materials #construction materials

🏗️ 8 TYPES OF MONOPITCH (SINGLE-SLOPE) ROOF STRUCTURES

A monopitch roof has a single sloping surface that directs rainwater to one side. It is commonly used in warehouses, workshops, sheds, and industrial buildings.

🔹 8 Common Types:

Pratt Truss
Howe Truss
Rafter System
Cranked Beam
Warren Truss
Arched Truss
Curved Beam
Arched Beam and Purlin System

📐 Key Design Considerations:

✅ Roof span and slope
✅ Dead, live, and wind loads
✅ Material and section selection
✅ Purlins, connections, and bracing
✅ Drainage and structural stability
✅ Applicable building codes

🏗️ Proper structural design ensures safety, durability, and efficient load transfer.

@etconp

🏗️TYPES OF AGGREGATES USED IN CONSTRUCTION

Aggregates are essential construction materials used in concrete, mortar, road construction, drainage systems and other civil engineering works.

They provide strength, stability, durability and volume to concrete.

Depending on their particle size, aggregates are broadly classified into Fine Aggregates and Coarse Aggregates.

1. Stone Dust (Quarry Dust)

- Size: Approximately 0–5 mm.
- Produced during the crushing of rocks.
- Used in concrete mixes, paving blocks and other construction applications.
- Can be used as a partial replacement for natural sand when properly graded and tested.

2. Fine Aggregate

- Generally passes through a 4.75 mm IS sieve.
- Examples: Natural sand, manufactured sand (M-sand).
- Used in concrete and mortar.
- Fills the voids between coarse aggregate particles.

3. Small Aggregate

- Example size range: 5–12 mm.
- Used in selected concrete mixes, precast products and other applications.
- Helps achieve the required particle-size distribution.

4. Medium Aggregate

- Example size range: 12–14.5 mm.
- Used where the specified grading and mix design require this fraction.

5. Coarse Aggregate (Gravel 1)

- Example size range: 12.5–22 mm.
- Used in concrete production.
- Contributes to the strength and stability of concrete.

6. Coarse Aggregate (Gravel 2)

- Example size range: 22–32 mm.
- Used in selected concrete and construction applications, subject to specifications.

7. Large Aggregate

- Example size range: 32–63 mm.
- Commonly used in selected mass concrete, drainage and other civil engineering applications.

8. Boulder Aggregate

- Example size range: 50–100 mm.
- Used in riprap, erosion protection, gabion works and heavy drainage applications.
- Not normally used as conventional structural concrete aggregate.

🗂Important Engineering Notes

📌 Fine aggregate generally passes the 4.75 mm sieve, while coarse aggregate is generally retained on it (IS 383 classification).

📌 Common nominal coarse aggregate sizes include 10 mm, 12.5 mm, 20 mm and 40 mm.

📌 Aggregate size selection depends on structural dimensions, reinforcement spacing, concrete cover, mix design and applicable specifications.

📌 Aggregates must be clean, durable and properly graded. Avoid excessive clay, silt and other harmful impurities.

🌟Remember: Aggregate grading directly influences concrete workability, strength, durability and economy. Always select aggregates according to the approved mix design and relevant standards.

Technical clarification: The particle-size ranges shown in the infographic are illustrative, not universal standard classifications.

In particular, 3–5 mm material is not conventionally classified entirely as fine aggregate under the 4.75 mm sieve definition.

Always follow the applicable project specification.

@etconp

📐 QUANTITY SURVEYING TIP: HOW TO CALCULATE WALL AREA

Wall area calculations are commonly used when estimating plastering, painting, tiling, and other finishing works.

🔹 Formula

Wall Area = Length × Height

🏗️ Example

A wall has:
Length = 6 m
Height = 3 m
Area = 6 × 3
Gross wall area = 18 m²

🔹 What About Doors and Windows?

Suppose the wall contains:
One door: 2.1 m × 0.9 m = 1.89 m².
One window: 1.2 m × 1.0 m = 1.20 m².
Total opening area = 1.89 + 1.20 = 3.09 m².
Net wall area = 18 − 3.09
Net wall area = 14.91 m²

📌 This is a simplified calculation. Actual BOQ measurement rules may specify whether openings, reveals, deductions, and other details are included.

🧠 Practice: A wall is 8 m long and 3.2 m high. What is its gross area?

@etconp

👉የህንፃ ዲዛይን ፕላን ማንበብ ያስቸግሮታል?

🏛ይህ Complete Guide to Reading Building Drawings የተሰኘ ምርጥ መፅሃፍ የህንፃን ድሮዊንግ በተግባር ለመረዳት እና ስለ ጠቅላላ አርክቴክቸር ሳይነስ የሚዳስስ ነው ከታች ባለው ሊንክ ያውሩዱት👇

https://ye-buna.com/etconp?ref=product_detail&product=6aa7c4a30b34d_etconp

♻️ 7 PRACTICAL WAYS TO REDUCE CONSTRUCTION WASTE

Construction waste increases disposal costs and can waste valuable materials.

Here are practical ways project teams can reduce unnecessary waste.

1️⃣ Improve Estimation: Use accurate quantities to avoid unnecessary ordering.
2️⃣ Plan Deliveries: Schedule materials to reduce damage and prolonged storage.
3️⃣ Protect Materials: Keep vulnerable materials dry, clean, and secure.
4️⃣ Optimize Cutting: Plan dimensions and cutting layouts to reduce offcuts.
5️⃣ Prevent Rework: Use approved drawings and inspect work at the right stages.
6️⃣ Separate Waste: Sort materials where recycling or recovery is available.
7️⃣ Monitor Consumption: Compare planned quantities with actual usage.

🏗️ Example: Better cutting plans for reinforcement, timber, tiles, and sheet materials can help reduce avoidable offcuts.

📌 Waste reduction must not compromise structural safety, specified material quality, or workmanship.

@etconp

🏗️ ፕሮፌሽናል CV እና Cover Letter📄

💼 ስራ እየፈለጉ ነው? የሚያስደንቅ CV ይዘው ለቀጣሪዎች ይቅረቡ!

🔥 30 የተለያዩ ፕሮፌሽናል CV እና Cover Letter ቴምፕሌቶች በአንድ ጥቅል!

✅ ለCivil Engineers፣ Site Engineers፣ Architects፣ Quantity Surveyors፣ Safety Officers እና ሌሎች የኮንስትራክሽን ባለሙያዎች
✅ ERA፣ AACRA፣ UN፣ AU እና ሌሎች ተቋማት የCV ፎርማቶች
✅ በMicrosoft Word ሙሉ በሙሉ የሚስተካከሉ
✅ ለአዲስ ተመራቂዎችና ልምድ ላላቸው ባለሙያዎች
🎯 ጊዜዎን ይቆጥቡ፤ CVዎን በፕሮፌሽናል መንገድ ያዘጋጁ👇

https://ye-buna.com/etconp?ref=product_detail&product=6ad07d3c7ba5f_etconp

🏢 BUILDING INFORMATION MODELING (BIM) — WHY IS IT IMPORTANT?

Building Information Modeling is a collaborative process for creating and managing digital information about a built asset.

BIM combines geometry with structured information that can support design, construction, and operation.

🔹 How Can BIM Help?

📐 Design Coordination: Helps teams coordinate architectural, structural, and service systems.

🔍 Clash Detection: Supports identification of conflicts between modeled elements.

📊 Quantity Takeoffs: Can support measurement when the model information is suitable.

📅 Construction Planning: Can connect model elements with schedule information.

💰 Cost Management: Can support estimating when quantities and cost data are appropriately structured.

🏢 Facility Management: Can provide useful asset information after construction.

🔹 Useful Skills to Develop

Revit or other appropriate modeling tools.

Model organization.

Drawing and schedule preparation.

Coordination workflows.

Information management.

📌 BIM is not simply 3D modeling. It depends on information quality, collaboration, and agreed project standards.

@etconp

🏗️ ኮንትራክተሮች እና የኮንስትራክሽን ባለሙያዎች

🌟Company Profile እና Tender Documents ለማዘጋጀት ጊዜያችሁን አታባክኑ!

🔥 Construction Business Toolkit 2026👇

📁 በአንድ ፓኬጅ ውስጥ፦
✅ 22-Page Editable Company Profile
✅ 39-Page Tender Preparation Kit
✅ 15 Business Letter Templates
✅ Excel Tender & Calculation Tools
✅ Project, Staff CV & Equipment Forms
✅ Completed Samples + User Guide

💻 በWord እና Excel ሊስተካከሉ የሚችሉ ፋይሎች አዘጋጅተናል ከታች ባለው ሊንክ ያውርዱት👇

https://ye-buna.com/etconp?ref=product_detail&product=6ad5de3247d30_etconp

🚆RAILWAY TURNOUT – COMPONENTS & DETAILS

A railway turnout is a track arrangement that allows trains to move from one railway track to another.

It is an essential component of railway track systems, enabling safe and efficient movement at junctions, sidings and railway yards.

🔹 Main Components of a Railway Turnout

1. Check Rail (Guard Rail): Guides the wheel flanges and helps prevent wheels from striking the crossing nose incorrectly.

2. Switch Rail (Switch Blade): Movable tapered rails that direct the train towards the selected track.

3. Sleepers (Railway Ties):  Support the rails, maintain track gauge and distribute wheel loads to the ballast.

4. Point Machine (Switch Machine): Mechanically or electrically operates the switch rails to change the train's route.

5. Stock Rail (Main Rail): Fixed rail against which the switch rail closes to guide the train.

6. Guard Rail: Helps control wheel movement and protects against derailment, particularly around crossing sections.

7. Crossing (Frog): Allows the wheel flanges to pass through the intersection of two rail paths.

8. Frog Guard Rails: Guide the wheelsets through the crossing and help ensure proper wheel passage.

🔹 Functions of a Railway Turnout

✅ Enables trains to change tracks safely.
✅ Connects main lines with sidings and branch lines.
✅ Facilitates railway yard operations.
✅ Supports efficient train movement and routing.
✅ Improves flexibility in railway operations.

📌 Engineering Note: Railway turnouts must be designed with proper switch geometry, crossing angle, gauge, fastening systems and alignment. Regular inspection and maintenance are essential for safe railway operation.

━━━━━━━━━━━━━━
​📌 ተጨማሪ ዝርዝር መረጃዎችን እና የሳምንቱን የኮንስትራክሽን ዜናዎች ለማግኘት ​የፌስቡክ ገፃችን ይጎብኙ👇

https://www.facebook.com/profile.php?id=61592085774934

@etconp

ተምር  ፕሌት እና ጄቦልት አቅራቢ

📌ፕሌትና ጄቦልት በፈለጉት አይነት የተዘጋጀ አለን

✂️ላሜራ መቁረጫ መብሻና  ማጠፊያ ማሽኖች አሉን

🔗ፌሮ (ቶንዲኖ) ጥርስ እናበጃለን እንዲሁም እናጥፋለን

📐ማንኛዉንም የሞደፊክ ስራዎችን እንሰራለን

📍ኢትዮጵያ ዉስጥ የትም እንልክሎታ

Telegram  https://t.me/heavenic1

tiktok.com/@blessedase1

🏗️ የመሬት ሥራ (Earthwork) – የግንባታ ስራ መሠረት!

በግንባታ ውስጥ የመሬት ዝግጅት ከሁሉም በላይ ትኩረት የሚፈልግ ስራ ነው።

በምስሉ ላይ የምናየው Bulldozer በመጠቀም የሚከናወን የመሬት ማስተካከያና የአፈር ማንቀሳቀስ ስራ ነው።

በዚህ ስራ ላይ ትኩረት መሰጠት ያለባቸው፦

✅ የመሬቱን ደረጃ (Level) በትክክል መወሰን።

✅ የአፈሩን አይነትና ተስማሚነት መመርመር።

✅ ትክክለኛ የCut and Fill ስራ ማከናወን።

✅ አፈሩን በተገቢው መንገድ ማጠቅለል (Compaction)።

⚠️ የመሬት ዝግጅት በትክክል ካልተሰራ ወደፊት የFoundation Settlement እና የመዋቅር ችግሮች ሊፈጠሩ ይችላሉ።

💬 የምህንድስና ጥያቄ!

በዚህ የEarthwork ስራ ውስጥ ከሁሉም በላይ ወሳኙ ምንድን ነው?

1️⃣ Proper Levelling
2️⃣ Soil Compaction
3️⃣ Soil Testing

የመረጡትን በComment ያስቀምጡ👇

​​🌐ለተጨማሪ መረጃ እና ሌሎች የኮንስትራክሽን ዘርፍ ዜናዎች የ YouTube ገፃችን ከታች ባለው ሊንክ በመግባት SubScribe አርገው ቤተሰብ ይሁኑ👇

https://youtube.com/@ethiopianconstruction7?si=ils307xXQQpIdCwG
‎
‎@etconp

👉የኮንስትራክሽን ሥራ ውል አዘገጃጀት — ሙያዊ መመሪያ በአማርኛ

🏛የኮንስትራክሽን ሥራ ውል ከመዘጋጀቱ በፊት ሊታወቁና ሊካተቱ የሚገባቸውን ዋና ዋና ጉዳዮች በአማርኛ የሚያብራራ ሙያዊ መመሪያ።

👷 ሲቪልና ኮንስትራክሽን መሐንዲሶች
⚖️ የሕግ ባለሙያዎች
🏗️ ተቋራጮችና አማካሪዎች
📋 ፕሮጀክት ማኔጀሮች
🎓 የኮንስትራክሽን ተማሪዎች የሚጠቅም ምርጥ መፅሐፍ ከታች ባለው ሊንክ ያውርዱት👇

https://ye-buna.com/etconp?ref=product_detail&product=6a9aa58c0b37b_etconp

🪜TYPES OF STAIRS IN BUILDING CONSTRUCTION | 20 COMMON STAIRCASE DESIGNS

☄Stairs are essential structural and architectural elements that provide safe and convenient vertical access between different floors of a building.

⬆️They are designed in different configurations depending on available space, building requirements, aesthetics, and functionality.

🌟Here are 20 common types of stairs used in building construction:

1. Straight Stair: A single flight of steps without any change in direction.
2. L-Shaped Stair: Two flights connected by a landing, changing direction by 90°.
3. U-Shaped Stair: Two parallel flights connected by a 180° turn.
4. Spiral Stair: A compact staircase arranged around a central column.
5. Curved Stair: A staircase with a gradual curved alignment.
6. Floating Stair: Treads supported by a wall or concealed structural system, creating an open appearance.
7. Cantilever Stair: Individual steps project from a supporting wall or structural element.
8. Winder Stair: Changes direction using triangular or tapered steps instead of a landing.
9. Split Stair: A staircase that divides into two separate flights.
10. Circular Stair: A curved or circular staircase often used in public and architectural spaces.
11. Helical Stair: A continuous curved staircase that generally does not have a central supporting column.
12. Ladder Stair: A steep staircase designed for restricted or limited-access areas.
13. Open-Riser Stair: A staircase with open gaps between successive treads.
14. Closed-Riser Stair: A staircase with vertical risers closing the gaps between treads.
15. Box Stair: A staircase with box-like construction, often used in compact spaces.
16. Quarter-Turn Stair: Changes direction by 90°, generally using a landing.
17. Half-Turn Stair: Changes direction by 180° using a central landing.
18. Bifurcated Stair: A wide lower flight that divides into two smaller upper flights.
19. Space-Saving Stair: A compact staircase designed for areas with limited floor space.
20. Monumental Stair: A wide, grand staircase commonly used in public and prestigious buildings.

📐 Important Staircase Design Dimensions

🚥Typical preliminary design recommendations:

- Rise: 150–190 mm
- Tread: 250–300 mm
- Handrail height:** 900–1,100 mm
- Minimum headroom: Approximately 2.1 m
- Landing length: Generally not less than the stair width.

📏 Important Staircase Design Formulas

🗂1. Number of risers:**

N = Total floor height ÷ Rise

🗂2. Number of treads:

Number of treads = Number of risers − 1 (for a typical single flight).

🗂3. Stair slope:

θ = tan⁻¹ (Rise ÷ Tread)

🗂4. Comfort formula:

2R + T = 600–650 mm

Where:
- R = Rise of the step
- T = Tread or going

⚠️ Engineering Note: These dimensions are general educational guidelines, not universal code requirements. Actual staircase dimensions, accessibility, fire safety, handrails, landings and structural reinforcement must comply with the applicable local building regulations.

🌟Remember: A properly designed staircase should provide safety, comfort, durability and efficient use of available space.

@etconp

‎👉ሙሉ የህንፃ ኤሌትሪክ ዲዛይን፣ መስመር ዝርጋታ እና የኤሌትሪክ ስራ የተግባር መማሪያ

⚡️‎በአማርኛ ቋንቋ የተዘጋጀ ይህ መፅሐፍ  የህንፃ ኤሌትሪክ ስራን ከመሠረታዊ እውቀት እስከ ተግባራዊ የመስመር ዝርጋታ ድረስ በቀላልና በተደራጀ መንገድ ለመማር የሚያግዝ ምርጥ መፅሐፍ ከፈለጉ ከታች ባለው ሊንክ PDF ያውርዱት👇
‎
‎https://ye-buna.com/etconp?ref=product_detail&product=6a8bcb2fa3202_etconp

👉የግንባታ ፕሮጀክትዎን BOQ፣ ወጪ፣ የሥራ አፈጻጸም፣ ክፍያ፣ Cash Flow እና Profit/Loss በአንድ ፕሮፌሽናል Excel System በቀላሉ ለማስተዳዳር የሚጠቅም Editable Microsoft Excel System ለContractors፣ Engineers፣ Quantity Surveyors፣ Construction PLCs፣ Consultants፣ Project Owners እና Project Managers ይጠቅማል ከታች ባለው ሊንክ ያውርዱት👇

https://ye-buna.com/etconp?ref=product_detail&product=6aaf8ac262672_etconp

👉Water Table & Subsurface Water Management

ባዶ የሆነ የ basement ቁፋሮ በዝናብ ወቅት ውኃ ሲሞላው አይተህ ታውቃለህ? ከሕንፃህ ሥር ያለው water table ከፍ ሲል ውኃው በ foundation slab ላይ ወደ ላይ ይገፋል፤ ይህ ግፊት ከሕንፃህ ክብደት ከበለጠ መዋቅርህ ልክ እንደ ጀልባ ከቦታው ሊነሳ ይችላል።

ውኃ እርጥበት ብቻ አይደለም፤ የሚገፋ ኃይል ነው!

ይህ ኃይል የሚመጣው ከሁለት መንገድ ነው። የመጀመሪያው ከአፈሩ ውስጥ ነው። Water table ወደ footing ደረጃ ሲጠጋ pore-water pressure (u) ይጨምራል፤ effective stress ደግሞ በ σ' = σ − u መሠረት ይቀንሳል።

Effective stress ሲቀንስ የአፈሩ shear strength ይቀንሳል፤ ማለትም ትናንት የሚሸከመው አፈር ዛሬ ያነሰ ይሸከማል።

ሁለተኛው ከመዋቅሩ ሥር ነው። ውኃው በ basement slab ሥር የሚፈጥረው ግፊት ከ slab አካባቢ ስፋት ጋር ሲባዛ ወደ ላይ የሚገፋ ጠቅላላ ኃይል ይሆናል። ይህ ኃይል ከሕንፃህ self-weight ጋር ይወዳደራል። በግንባታ ላይ ባለ ጊዜ ወለሎቹ ገና ስላልተሠሩ ሕንፃው ቀላል ነው፤ ስለዚህ አደጋው ከፍተኛ የሚሆነው ብዙ ጊዜ በዚያን ወቅት ነው። Dewatering ተቋርጦ ውኃው ሲመለስ ባዶው መዋቅር ሊንሳፈፍ ይችላል።

ጎን ላይም ተመሳሳይ ታሪክ አለ። በ retaining ወይም basement walls ጀርባ ውኃ ከተከማቸ lateral hydrostatic pressure ይፈጠራል፤ ይህ ግፊት ከአፈር ግፊት ጋር ተደምሮ ግድግዳው እንዲሸከም የተነደፈውን ጭነት ሊያልፍ ይችላል።

ታዲያ ይህን እንዴት ትቆጣጠረዋለህ? መከላከያው በበርካታ ንብርብሮች ይሰራል፤ እያንዳንዱም የተለየ ሥራ አለው።

መጀመሪያ ውኃው ወደ መዋቅርህ ከመድረሱ በፊት ማቋረጥ ነው። French drains፣ perforated pipes እና በ granular filter media የተከበቡ drainage layers ውኃውን ይሰበስባሉ፤ በዚህም hydraulic pressure ይቀንሳል። ከግድግዳዎችህ ጀርባ ደግሞ weep holes ውኃው ተከማችቶ ግፊት እንዳይፈጥር መውጫ ይሰጡታል፤ እነዚህ ከተደፈኑ ግድግዳህ በጸጥታ ወደ dam ይቀየራል፤ ከውጭ ምንም አይመስልም፣ ከጀርባው ግን ግፊቱ እያደገ ይሄዳል።

የተሰበሰበው ውኃ ግን የሆነ ቦታ መድረስ አለበት። እዚህ ላይ sump pit (አንዳንዴ sump well ይባላል) ይገባል።

ቱቦዎቹ ውኃውን ወደ ዝቅተኛው ነጥብ ይመራሉ፤ በዚያ የተሠራው sump pit ያከማቸዋል።

በ pit ውስጥ የተቀመጠው submersible pump የውኃው ደረጃ ሲጨምር (ብዙ ጊዜ በ float switch እየተነቃቃ) ውኃውን ወደ ላይ አንስቶ ከሕንፃው ራቅ ወዳለ ተስማሚ መውጫ ያስወጣዋል።

በግንባታ ወቅት ቁፋሮው ደረቅ እንዲሆን የሚደረገው dewatering ተመሳሳይ መርህ ይጠቀማል።

አንድ ነገር ግን አትርሳ፦ pump በኃይል ላይ የተመሠረተ ነው። መብራት ሲቋረጥ ወይም pump ሲበላሽ ውኃው ተመልሶ መከማቸት ይጀምራል፤ uplift እና hydrostatic pressureም ይመለሳሉ።

ስለዚህ standby pump፣ አማራጭ የኃይል ምንጭ እና በ sump ውስጥ የሚጠራቀም ደለልን በየጊዜው ማጽዳት የንድፉ አካል ናቸው።

በመጨረሻ waterproofing ይመጣል። Membranes፣ Cementitous coatings ውኃ ወደ ውስጥ እንዳይገባ ይከላከላሉ። ግን waterproofing ውኃ እንዳይሰርግ ያደርጋል እንጂ hydrostatic pressureን አያስወግድም።

ግፊቱን የሚቀንሰው drainage ነው፤ ወይም መዋቅሩ ራሱ ለዚያ ግፊት ተነድፎ መሆን አለበት።

እነዚህ ሁሉ ከተደረጉም uplift አሁንም ችግር ከሆነ ሌሎች መፍትሄዎች አሉ፤ ለምሳሌ ተጨማሪ ክብደት መጨመር ወይም tension anchors መጠቀም። የትኛው እንደሚመረጥ በንድፍ መሐንዲሱና በጂኦቴክኒክ ጥናቱ ይወሰናል።

ዋናው ሥራ ግን ከቁፋሮ በፊት ይጀምራል። Water table አንድ ጊዜ ተለክቶ የሚቆም ቁጥር አይደለም፤ በበጋና በክረምት ይለያያል።

የ groundwater ደረጃን በ boreholes ወይም piezometers ተከታትለህ፣ በተለይ በዝናብ ወቅት ያለውን ከፍተኛ ደረጃ ለንድፍህ መነሻ አድርግ።

✅ከመሬት በላይ የሚታየውን ከመንከባከብህ በፊት ከሥሩ ላለው ውኃ መውጫ መንገድ አሳየው፤ ውኃ መውጫ ካላገኘ የራሱን መንገድ ይፈጥራል።

Via Ecem solutions

​​🌐ለተጨማሪ መረጃ እና ሌሎች የኮንስትራክሽን ዘርፍ ዜናዎች የ YouTube ገፃችን ከታች ባለው ሊንክ በመግባት SubScribe አርገው ቤተሰብ ይሁኑ👇

https://youtube.com/@ethiopianconstruction7?si=ils307xXQQpIdCwG
‎
‎@etconp

👉የ ህንፃ ዲዛይን አዘጋጅታቹ ለማፅደቅ ዲዛይኑ መካተት ያለባቸው የአርክቴክቸራል፣ስትራክቸራል፣ሳኒተሪ እና ኤሌክትሪካል ቼክሊስቶች ከፈለጉ ከታች ባለው ሊንክ ያውርዱ👇

https://ye-buna.com/etconp?ref=product_detail&product=6a76b89233390_etconp

🛣️ROAD ALIGNMENT SURVEYING – HORIZONTAL CURVE SETTING

Horizontal curve setting is an important surveying operation used in road construction to establish smooth and accurate curved road alignments between two straight sections.

A Total Station is commonly used to set out the road centreline, inner edge and outer edge of a horizontal curve with high accuracy.

📌Key Components

1️⃣Road Alignment (Centreline): The reference line that defines the designed path of the road.

2️⃣ Inner Edge (Offset): The inside boundary of the curved roadway, established using calculated offsets from the centreline.

3️⃣ Outer Edge (Offset): The outside boundary of the roadway, marked according to the design width and curve geometry.

4️⃣ Total Station: An electronic surveying instrument used to measure horizontal angles, vertical angles and distances for accurate curve setting.

5️⃣ Prism (Range Pole): A reflecting target used with the Total Station to determine precise survey points on the ground.

📐Basic Procedure for Horizontal Curve Setting:

1. Study the approved road alignment and horizontal curve design.
2. Establish control points and benchmarks.
3. Set up and orient the Total Station.
4. Calculate curve parameters, including radius, tangent length and deflection angles.
5. Mark the road centreline points using calculated coordinates.
6. Establish inner and outer road edges using the required offsets.
7. Check all points for alignment, levels and design accuracy.
8. Transfer the final setting-out points to the construction team.

⚠️Important Engineering Note

The centreline and edge offsets must be calculated from the approved geometric design. Do not assume that the inner and outer edges are always parallel at a constant offset without considering the specified road geometry.

Proper horizontal curve setting ensures smooth vehicle movement, improved road safety, accurate earthwork quantities and better construction quality.

@etconp

👉ምርጥ 120 ካሬ ላይ የሚያርፍ የመኖርያ ቤት ሙሉ ዲዛይን የምትፈልጉ ከታች ባለው ሊንክ ያውርዱ👇

https://ye-buna.com/etconp?ref=product_detail&product=6a62fd7b49a15_etconp