RW-6 - CoTM.pptx
3.7 MB
railway chap 6
▶️TODAY GREAT TIP @COTMp
:
👉አብዛኛዎቻቹ በጠየቃችሁን መሰረት የተለያዩ የ PDF መፅሀፍቶች እንካቹ ብለናል፡፡
፡
🅾አሁኑኑ Join በማረግ እና ለጓደኛዎ እና ለሚያቁት ሁሉ ሼር ያድርጉ።
፡
👆👆👆👆👆👆👆👆👆👆👆👆👆👆👆👆
:
👉አብዛኛዎቻቹ በጠየቃችሁን መሰረት የተለያዩ የ PDF መፅሀፍቶች እንካቹ ብለናል፡፡
፡
🅾አሁኑኑ Join በማረግ እና ለጓደኛዎ እና ለሚያቁት ሁሉ ሼር ያድርጉ።
፡
👆👆👆👆👆👆👆👆👆👆👆👆👆👆👆👆
Forwarded from Ethio Construction Engineering (जॉर्डनो ג׳ורדנו ጆርዳኖ جوردانو จอร์แดโน่ JORDANO Ιορδάνοςஜார்டானோ)
Define the following terms
1.sliding vector
2. Free vector
3. fixed vector
1.sliding vector
2. Free vector
3. fixed vector
Forwarded from Ethio Construction Engineering
👉 PRE-STRESSED CONCRETE (PSC) @COTMp
.
ፕሪ እስትረስድ ኮንክሪት - ኮንክሪቱ ላይ ሎድ ከመጫኑ በፊት
Axial Compressive Stress አፕላይ ይደረግባቸዋል….
ለምሳሌ አንድን ቢም ከጎንና ከጎን Compressive ፎርስ
ስናደርግበት የ ‹‹ በ ›› ፊደል አይነት ቅርፅ ይኖረዋል (ሲጋነን)
….. ኢሄ የታጠፈው ቢም እላዩ ላይ ሎድ ሲጫንበት ቢሙ ወደ
ነበረበት ቦታው ይመለሳል…. እንደዛ ነው pre-stressed
ኮንክሪቶች act የሚያደርጉት
.
✔PSC Vs RC
1 RC beam ላይ ለዲዛይን assume ስናደርግ ኮንክሪቱ ምንም አይነት tensile stress አይሸከምም - tensile እስትረሱን
የሚሸከመው ፌሮው ነው ብለን ነው…… ሌላው assumption ፌሮው ቴንሽኑን ይሸከማል ብንልም
የፌሮውን አቅም fully utilize አናደርገውም ወይም ደሞ ሙሉ
ለሙሉ አንጠቀምበትም የዚህም ምክንያቱ ኮንክሪቱ ቴንሽን ዞን
ውስጥ የሚከሰተውን Crack width ለመገደብ ወይም limit
ለማድረግ ነው
.
ከላይ በተገለፁት ሁለት ምክንያቶች ማለትም የኮንክሪቱንም የፌሮውንም አቅም ሙሉ ለሙሉ ባለመጠቀማችን የተነሳ ለትልልቅ ሎዶች RC ከ PSC አንፃር ኢኮኖሚካል አይደለም ….. የዚህም ምክንያቱ የ RCን አቅም ሙሉ ለሙሉ ስለማንጠቀምበት ነው….. በተጨማሪም RC ላይ ትልልቅ Grade ያላቸው ኮንክሪትና ፌሮ መጠቀማችን ብዙም ዋጋ የለውም……. ከ RC ድክመት ለመዳን Pre-Stressed ኮንክሪቶች ተፈጠሩ…… ከRC
በተሻለ መልኩ የኮንክሪቱንና የብረቱን እስትሬንግዝ ይጠቀማሉና
.
✔ Methods of Prestressing
1) Pre- tensioning -> ቢሙን ካስት ማድረጊያ mold እናዘጋጃለን… ሞልድ ውስጥም psc ኬብሎች ወይም tendon
እናስቀምጣለን…እነዚህ ኬብሎችም ላይ Tensile ፎርስ apply እናደርጋለን….. አፕላይ እንደተደረገ ኮንክሪቱን ሞልድ ውስጥ አስገብተን ኮንክሪቱን ካስት እናደርጋለን - ኮንክሪቱ ሲደርቅ ፎርሶቹን remove እናደርጋለን … ቢሙም ዝግጁ ሆነ ማለት ነው::
2) Post –tensioning -> ኮንክሪቱ ከደረቀ በኋላ ነው
Compressive force አፕላይ የምናደርገው:: Apply የሚደረጉት ፎርሶች ኮንክሪቱ ላይ compressive stress
ሲፈጥሩ ብረቱ ላይ ደሞ tensile stress ይፈጥራሉ ማለት ነው::
.
👉ለሁሉም እንዲዳረስ እባክዎ Share ያድርጉ::
.
ፕሪ እስትረስድ ኮንክሪት - ኮንክሪቱ ላይ ሎድ ከመጫኑ በፊት
Axial Compressive Stress አፕላይ ይደረግባቸዋል….
ለምሳሌ አንድን ቢም ከጎንና ከጎን Compressive ፎርስ
ስናደርግበት የ ‹‹ በ ›› ፊደል አይነት ቅርፅ ይኖረዋል (ሲጋነን)
….. ኢሄ የታጠፈው ቢም እላዩ ላይ ሎድ ሲጫንበት ቢሙ ወደ
ነበረበት ቦታው ይመለሳል…. እንደዛ ነው pre-stressed
ኮንክሪቶች act የሚያደርጉት
.
✔PSC Vs RC
1 RC beam ላይ ለዲዛይን assume ስናደርግ ኮንክሪቱ ምንም አይነት tensile stress አይሸከምም - tensile እስትረሱን
የሚሸከመው ፌሮው ነው ብለን ነው…… ሌላው assumption ፌሮው ቴንሽኑን ይሸከማል ብንልም
የፌሮውን አቅም fully utilize አናደርገውም ወይም ደሞ ሙሉ
ለሙሉ አንጠቀምበትም የዚህም ምክንያቱ ኮንክሪቱ ቴንሽን ዞን
ውስጥ የሚከሰተውን Crack width ለመገደብ ወይም limit
ለማድረግ ነው
.
ከላይ በተገለፁት ሁለት ምክንያቶች ማለትም የኮንክሪቱንም የፌሮውንም አቅም ሙሉ ለሙሉ ባለመጠቀማችን የተነሳ ለትልልቅ ሎዶች RC ከ PSC አንፃር ኢኮኖሚካል አይደለም ….. የዚህም ምክንያቱ የ RCን አቅም ሙሉ ለሙሉ ስለማንጠቀምበት ነው….. በተጨማሪም RC ላይ ትልልቅ Grade ያላቸው ኮንክሪትና ፌሮ መጠቀማችን ብዙም ዋጋ የለውም……. ከ RC ድክመት ለመዳን Pre-Stressed ኮንክሪቶች ተፈጠሩ…… ከRC
በተሻለ መልኩ የኮንክሪቱንና የብረቱን እስትሬንግዝ ይጠቀማሉና
.
✔ Methods of Prestressing
1) Pre- tensioning -> ቢሙን ካስት ማድረጊያ mold እናዘጋጃለን… ሞልድ ውስጥም psc ኬብሎች ወይም tendon
እናስቀምጣለን…እነዚህ ኬብሎችም ላይ Tensile ፎርስ apply እናደርጋለን….. አፕላይ እንደተደረገ ኮንክሪቱን ሞልድ ውስጥ አስገብተን ኮንክሪቱን ካስት እናደርጋለን - ኮንክሪቱ ሲደርቅ ፎርሶቹን remove እናደርጋለን … ቢሙም ዝግጁ ሆነ ማለት ነው::
2) Post –tensioning -> ኮንክሪቱ ከደረቀ በኋላ ነው
Compressive force አፕላይ የምናደርገው:: Apply የሚደረጉት ፎርሶች ኮንክሪቱ ላይ compressive stress
ሲፈጥሩ ብረቱ ላይ ደሞ tensile stress ይፈጥራሉ ማለት ነው::
.
👉ለሁሉም እንዲዳረስ እባክዎ Share ያድርጉ::
👍1
👉 @COTMp Types-of-Cracks-in-Concrete-Columns-
Forwarded from Ethio Construction Engineering
👉ADMIXTURES @COTMp
~~~~~~~~~~~~~~~~
➡Admixtures are the special ingredients added during concrete mixing to enhance the properties and performance of fresh concrete. Various types of
admixtures are available in the market which is
used in construction work.
.
➡FUNCTION OF ADMIXTURES:
1. To accelerate or retard the setting time of fresh
concrete.
2. To improve the workability or flowability of
concrete.
3. To increase the strength and durability of
concrete.
4. To reduce the heat of hydration.
5. To reduce the segregation and bleeding.
6. To decrease the permeability.
7. To achieve other desired properties.
.
➡TYPES OF ADMIXTURES:
1. ACCELERATING ADMIXTURES:
This admixture is added in concrete or mortar for
increasing the rate of hydration of hydraulic cement and for shortening the setting time. Calcium
chloride (CaCl2) is the most widely used
accelerating admixture.
2. RETARDING ADMIXTURES:
Retarding admixtures delay the initial rate of
hydration of cement and extend the setting time of
cement paste. This admixture can be used in high temperature and where the concrete has to be transported to a long distance. It is also suitable for using in grouting oil wells.
3. AIR-ENTRAINING ADMIXTURES:
Air entraining admixtures help to produce a certain
amount of air bubbles in the concrete mixture. The
main goal of this admixture is to increase the resistance against freeze-thaw degradation and cohesion. It also improves the workability of fresh concrete without changing the setting or the rate of hardening.
4. WATER REDUCING ADMIXTURES:
As the name suggest, water reducers are added to a concrete mixture, mortar or grout to increase the flow ability without increasing the water content.
▶Advantages Of Water Reducing Admixtures:
1. The rate of concrete placement is faster.
2. Strength, durability, density etc. are significantly improved.
3. Segregation, permeability, and cracking are reduced.
.
➡SPECIAL ADMIXTURES:
1. Superplasticizing admixtures.
2. Corrosion-inhibiting admixtures.
3. Grouting admixtures.
4. Coloring admixtures etc.
.
👇👇👇👇👇
Join for more updates via the link below;
t.me/COTMp
👆👆👆👆👆
⚡ አሁኑኑ Join በማረግ እና ለጓደኛዎ እና ለሚያቁት ሁሉ ሼር ያድርጉ።
~~~~~~~~~~~~~~~~
➡Admixtures are the special ingredients added during concrete mixing to enhance the properties and performance of fresh concrete. Various types of
admixtures are available in the market which is
used in construction work.
.
➡FUNCTION OF ADMIXTURES:
1. To accelerate or retard the setting time of fresh
concrete.
2. To improve the workability or flowability of
concrete.
3. To increase the strength and durability of
concrete.
4. To reduce the heat of hydration.
5. To reduce the segregation and bleeding.
6. To decrease the permeability.
7. To achieve other desired properties.
.
➡TYPES OF ADMIXTURES:
1. ACCELERATING ADMIXTURES:
This admixture is added in concrete or mortar for
increasing the rate of hydration of hydraulic cement and for shortening the setting time. Calcium
chloride (CaCl2) is the most widely used
accelerating admixture.
2. RETARDING ADMIXTURES:
Retarding admixtures delay the initial rate of
hydration of cement and extend the setting time of
cement paste. This admixture can be used in high temperature and where the concrete has to be transported to a long distance. It is also suitable for using in grouting oil wells.
3. AIR-ENTRAINING ADMIXTURES:
Air entraining admixtures help to produce a certain
amount of air bubbles in the concrete mixture. The
main goal of this admixture is to increase the resistance against freeze-thaw degradation and cohesion. It also improves the workability of fresh concrete without changing the setting or the rate of hardening.
4. WATER REDUCING ADMIXTURES:
As the name suggest, water reducers are added to a concrete mixture, mortar or grout to increase the flow ability without increasing the water content.
▶Advantages Of Water Reducing Admixtures:
1. The rate of concrete placement is faster.
2. Strength, durability, density etc. are significantly improved.
3. Segregation, permeability, and cracking are reduced.
.
➡SPECIAL ADMIXTURES:
1. Superplasticizing admixtures.
2. Corrosion-inhibiting admixtures.
3. Grouting admixtures.
4. Coloring admixtures etc.
.
👇👇👇👇👇
Join for more updates via the link below;
t.me/COTMp
👆👆👆👆👆
⚡ አሁኑኑ Join በማረግ እና ለጓደኛዎ እና ለሚያቁት ሁሉ ሼር ያድርጉ።
Telegram
ETCONp Discussion
📩ለማነኛውም ሀሳብ እና አስተያየት @Philemona7
✌️ይህ የ @etconp መወያያ ግሩፓቹ ነው።
✋This is discussion group of @ETCONpWORK
.
🔖ማሳሰብያ ...
.
⚡️ግሩፑ ላይ ማነኛውም ከ ኮንስትራክሽን ጉዳዮች ውጪ መለጠፍ በፍፁም አይፈቀድም!
@ETCONpBOT ፃፉልን እናመሰግናለን🙏
✌️ይህ የ @etconp መወያያ ግሩፓቹ ነው።
✋This is discussion group of @ETCONpWORK
.
🔖ማሳሰብያ ...
.
⚡️ግሩፑ ላይ ማነኛውም ከ ኮንስትራክሽን ጉዳዮች ውጪ መለጠፍ በፍፁም አይፈቀድም!
@ETCONpBOT ፃፉልን እናመሰግናለን🙏
❤1
Forwarded from Ethio Construction Engineering
👉ኣሁን ደሞ ስለ Lap length እንማማር @COTMp
.
▶Lap length in Reinforced
Concrete Lap length is one of the important term in the reinforcement. This is usually confused with
another important term called development length and anchorage length.
In this article, the lap lengths of bars is discussed. During the
placement of steel in Reinforced concrete
structure , if the required length of single bar
may fall short. To get the desired design length, lapping of two bars side by side is done.
An alternative to this is to provide mechanical couplers.
*steel bars overlapped
Lapping can be defined as the overlapping of two bars side by side to upto the design length. Usually, the stock length of steel bars is limited to 12m. *This is for easy
transportation of steel bars to the construction
site. For example, imagine there is a need to build a 100ft tall column. But it’s not practically available. Hence the bars are cut
every second story.
steel bars overlapped Then the tension forces are required to be transferred from one bar to the other bar at the location of discontinuity of the bar.
So the second bar is kept closely to the first bar and
overlapping is done.
This amount of overlapping between two bars is called “lap length”. *Lapping is usually done where minimum bending stress is encountered. In
general, lap length is 50d which means 50 times the bar diameter, if both bars are of same diameter.
*Lap length of bars with same diameter Lap length in tension: The lap length including anchorage value of hooks shall be For flexural tension – Ld or 30d whichever is greater is considered.
*For direct tension – 2Ld or 30d whichever is greater is considered.
*The straight length of lapping of bars shall not
be less than 15d or 20cm.
Lap Length in Compression: The lap length is equal to the development length calculated in compression but not less than 24d.
*For Different Diameter Bars: When the bars of different diameters are to be spliced, the lap length is calculated considering
the smaller diameter bar.
*Lap Splices:- Lap splices should not be catered for the bars
which are having diameter greater than 36 mm.
In such cases, welding should be considered.
*But if welding is also not feasible in some conditions, then lapping may be allowed for the bars larger than 36 mm diameter. But along with lapping, additional spirals of 6 mm should be provided around the lapped bars.
*Lap splice length in a footing Lap length for concrete of 1:2:3 Nominal mix: The Lapping length in tension (MS bar – mild
steel bar) including anchorage value is 58d. So
eliminating the anchorage value, the lap length
= 58d – 2*9d = 40d. (Where 9d = hook
*allowance up to 25 mm and k=2)
*Lap length for C-25 concrete:
*Columns – 45d
*Beams – 60d
*Slabs – 60d
This infers that if we need to lap 20 mm diameter column bars, a minimum lap of 45 * 20 = 900 mm is provided.
.
👇👇👇👇👇
Join for more updates via the link below;
t.me/COTMp
👆👆👆👆👆
⚡ አሁኑኑ Join በማረግ እና ለጓደኛዎ እና ለሚያቁት ሁሉ ሼር ያድርጉ።
.
▶Lap length in Reinforced
Concrete Lap length is one of the important term in the reinforcement. This is usually confused with
another important term called development length and anchorage length.
In this article, the lap lengths of bars is discussed. During the
placement of steel in Reinforced concrete
structure , if the required length of single bar
may fall short. To get the desired design length, lapping of two bars side by side is done.
An alternative to this is to provide mechanical couplers.
*steel bars overlapped
Lapping can be defined as the overlapping of two bars side by side to upto the design length. Usually, the stock length of steel bars is limited to 12m. *This is for easy
transportation of steel bars to the construction
site. For example, imagine there is a need to build a 100ft tall column. But it’s not practically available. Hence the bars are cut
every second story.
steel bars overlapped Then the tension forces are required to be transferred from one bar to the other bar at the location of discontinuity of the bar.
So the second bar is kept closely to the first bar and
overlapping is done.
This amount of overlapping between two bars is called “lap length”. *Lapping is usually done where minimum bending stress is encountered. In
general, lap length is 50d which means 50 times the bar diameter, if both bars are of same diameter.
*Lap length of bars with same diameter Lap length in tension: The lap length including anchorage value of hooks shall be For flexural tension – Ld or 30d whichever is greater is considered.
*For direct tension – 2Ld or 30d whichever is greater is considered.
*The straight length of lapping of bars shall not
be less than 15d or 20cm.
Lap Length in Compression: The lap length is equal to the development length calculated in compression but not less than 24d.
*For Different Diameter Bars: When the bars of different diameters are to be spliced, the lap length is calculated considering
the smaller diameter bar.
*Lap Splices:- Lap splices should not be catered for the bars
which are having diameter greater than 36 mm.
In such cases, welding should be considered.
*But if welding is also not feasible in some conditions, then lapping may be allowed for the bars larger than 36 mm diameter. But along with lapping, additional spirals of 6 mm should be provided around the lapped bars.
*Lap splice length in a footing Lap length for concrete of 1:2:3 Nominal mix: The Lapping length in tension (MS bar – mild
steel bar) including anchorage value is 58d. So
eliminating the anchorage value, the lap length
= 58d – 2*9d = 40d. (Where 9d = hook
*allowance up to 25 mm and k=2)
*Lap length for C-25 concrete:
*Columns – 45d
*Beams – 60d
*Slabs – 60d
This infers that if we need to lap 20 mm diameter column bars, a minimum lap of 45 * 20 = 900 mm is provided.
.
👇👇👇👇👇
Join for more updates via the link below;
t.me/COTMp
👆👆👆👆👆
⚡ አሁኑኑ Join በማረግ እና ለጓደኛዎ እና ለሚያቁት ሁሉ ሼር ያድርጉ።
Telegram
ETCONp Discussion
📩ለማነኛውም ሀሳብ እና አስተያየት @Philemona7
✌️ይህ የ @etconp መወያያ ግሩፓቹ ነው።
✋This is discussion group of @ETCONpWORK
.
🔖ማሳሰብያ ...
.
⚡️ግሩፑ ላይ ማነኛውም ከ ኮንስትራክሽን ጉዳዮች ውጪ መለጠፍ በፍፁም አይፈቀድም!
@ETCONpBOT ፃፉልን እናመሰግናለን🙏
✌️ይህ የ @etconp መወያያ ግሩፓቹ ነው።
✋This is discussion group of @ETCONpWORK
.
🔖ማሳሰብያ ...
.
⚡️ግሩፑ ላይ ማነኛውም ከ ኮንስትራክሽን ጉዳዮች ውጪ መለጠፍ በፍፁም አይፈቀድም!
@ETCONpBOT ፃፉልን እናመሰግናለን🙏
❤1