Ethio Construction Engineering via @like
Question on hydraulics For critical depth of flow water in open channels , 𝑓𝑐 the specific energy must be : 1. Minimum 2. Maximum 3. 1 and 2 are the answer 4. None of the above @etconp
[ Civil_zne ] Handbook of Hydraulics@etconp.pdf
31.5 MB
Handbook of hydraulics
Copyright © Horace Williams king
Contains 10 chapters
Content
1. Hydraulic units
2. Hydrostatics
3. Orifices
4. SHARP CRESTED WEIRS
5. Wires not sharp crest
6. Flow of water through pipes
7. Flow of water in open channels
8. Measurement of flowing water
9. Special problems
10. General reference table
It’s 445 pages
445 ገፅ ነው።
የፋይል መጠን 31.4MB
File size :- 31.4 MB
Special thanks to civil zone
@etconp
Copyright © Horace Williams king
Contains 10 chapters
Content
1. Hydraulic units
2. Hydrostatics
3. Orifices
4. SHARP CRESTED WEIRS
5. Wires not sharp crest
6. Flow of water through pipes
7. Flow of water in open channels
8. Measurement of flowing water
9. Special problems
10. General reference table
It’s 445 pages
445 ገፅ ነው።
የፋይል መጠን 31.4MB
File size :- 31.4 MB
Special thanks to civil zone
@etconp
Forwarded from Ethio Construction Engineering
👉 የትኛው ኢኮኖሚካል ነው ?? => Flat Plate, Waffle, Flat
with Drop or Solid Slab @COTMp
.
.
በጠቅላላው በፍሎር ደረጃ ኢሄኛው የተሻለ ኢኮኖሚካል ነው
አይደለም ለማለት Quantity ካልሰራን ለማወቅ አስቸጋሪ ነው ….
በፓኔል ደረጃ ( ስለአንድ እስላብ ብቻ ) ካወራን ግን EBCS
ሪኮመንድ የሚያረጋቸው የስላብ አይነቶች አሉ ፡፡ ሪኮመንዴሽኑ
100 ፐርሰንት ትክክል ነው ማለት አይደለም - ኢኮኖሚካል ነው
ለማለት ጂኦሜትሪንና የፌሮ ብዛትን ግምት ውስጥ ማስገባት
አለብን - ስለዚህ አሁንም 100 ፐርሰንት እርግጠኛ የምንሆነው
ኳንቲቲ በመስራት ብቻ ነው፡፡ ነገር ግን ኮዱ ባደረገው ጥናት
መሰረት ከኮለን እስከ ኮለን ያለውን ርቀት መሰረት አድርጎ
ኢኮኖሚካል ነው ያለውን የስላብ አይነት አስቀምጡዋል፡፡
እነዚህም፡
.
.
1. Flat Plate - ሎዱ ቀላል ከሆነና ከኮለን ሴንተር እስከ ኮለን
ሴንተር ከ4.5 እስከ 6ሜ ለሆነ ስላብ ኢኮኖሚካል ነው
.
2. Flat Slab With Drop - ከባድ ሎድ ካለና ከሴንተር -
ሴንተር ከ6 እስከ 9ሜ. ለሆነ እስላብ ኢኮኖሚካል ነው፡፡
.
3. Waffle Slab - ለትልቅ እስፓን ከ7.5 – 12ሜ………
ለትልቅ እስፓን ከmoment ይልቅ vertical load ገቨርን
ስለሚያደርግ መሃል ስፓን ላይ ያለውን የስላብ ውፍረት መቀነስ
እንችላለን - ዋፍል ስላብ በመጠቀም ማለት ነው፡፡
.
4. Ribbed Slab -ትልቅ ስፓን ላላቸውና ከቀላል እስከ
መካከለኛ የሆነ ተንቀሳቃሽ ሎድ ላላቸው ፓኔሎች ኢኮኖሚካል
ነው፡፡
.
5. Solid Slab - የስፓኑ ርዝመት በጨመረ ቁጥር ኢኮኖሚካል
አይደለም፡፡ ፍላት ስላቦች ናቸው ኢኮኖሚካል የሚሆኑት
ምክንያቱም የፍላት ስላብ ብረት አቀማመጥ በ Strip ስለሆነ
የፌሮ ብዛት ይቀንሳል::
with Drop or Solid Slab @COTMp
.
.
በጠቅላላው በፍሎር ደረጃ ኢሄኛው የተሻለ ኢኮኖሚካል ነው
አይደለም ለማለት Quantity ካልሰራን ለማወቅ አስቸጋሪ ነው ….
በፓኔል ደረጃ ( ስለአንድ እስላብ ብቻ ) ካወራን ግን EBCS
ሪኮመንድ የሚያረጋቸው የስላብ አይነቶች አሉ ፡፡ ሪኮመንዴሽኑ
100 ፐርሰንት ትክክል ነው ማለት አይደለም - ኢኮኖሚካል ነው
ለማለት ጂኦሜትሪንና የፌሮ ብዛትን ግምት ውስጥ ማስገባት
አለብን - ስለዚህ አሁንም 100 ፐርሰንት እርግጠኛ የምንሆነው
ኳንቲቲ በመስራት ብቻ ነው፡፡ ነገር ግን ኮዱ ባደረገው ጥናት
መሰረት ከኮለን እስከ ኮለን ያለውን ርቀት መሰረት አድርጎ
ኢኮኖሚካል ነው ያለውን የስላብ አይነት አስቀምጡዋል፡፡
እነዚህም፡
.
.
1. Flat Plate - ሎዱ ቀላል ከሆነና ከኮለን ሴንተር እስከ ኮለን
ሴንተር ከ4.5 እስከ 6ሜ ለሆነ ስላብ ኢኮኖሚካል ነው
.
2. Flat Slab With Drop - ከባድ ሎድ ካለና ከሴንተር -
ሴንተር ከ6 እስከ 9ሜ. ለሆነ እስላብ ኢኮኖሚካል ነው፡፡
.
3. Waffle Slab - ለትልቅ እስፓን ከ7.5 – 12ሜ………
ለትልቅ እስፓን ከmoment ይልቅ vertical load ገቨርን
ስለሚያደርግ መሃል ስፓን ላይ ያለውን የስላብ ውፍረት መቀነስ
እንችላለን - ዋፍል ስላብ በመጠቀም ማለት ነው፡፡
.
4. Ribbed Slab -ትልቅ ስፓን ላላቸውና ከቀላል እስከ
መካከለኛ የሆነ ተንቀሳቃሽ ሎድ ላላቸው ፓኔሎች ኢኮኖሚካል
ነው፡፡
.
5. Solid Slab - የስፓኑ ርዝመት በጨመረ ቁጥር ኢኮኖሚካል
አይደለም፡፡ ፍላት ስላቦች ናቸው ኢኮኖሚካል የሚሆኑት
ምክንያቱም የፍላት ስላብ ብረት አቀማመጥ በ Strip ስለሆነ
የፌሮ ብዛት ይቀንሳል::
Forwarded from Ethio Construction Engineering
➡Center of gravity Vs Centroid @COTMp
.
Center of Gravity = አንድ አካል በብዙ ጥቃቅን አካላት
የተመሰረተና የእነዚህ አካላት ስብስብ መሆኑ ይታወቃል፡፡ እናም
እነዚህ አካላት የየራሳቸው weight ወይም ክብደት አላቸው -
weighታቸውንም በአንድ weight መወከል እንችላለን ይህም
Resultant ይባላል፡፡ ይህ Resultant act የሚያደርግበት ቦታ
Center of Gravity ይባላል፡፡
.
Center of Mass = ከCenter of Gravity ጋር የሚለያየው በ
‘Weight’ ቦታ ‘Mass’ ስናስገባበት Center Of Mass
እናገኛለን (W = mg)
.
Centroid = የአንድ አካል ቅርፅ ላይ ( length , width &
height ) ላይ የሚመሰረት የአካሉ መሃከለኛ ቦታ ነው፡፡ እንዲሁ
በተለምዶ የአንድ አካል መሃል ነው የምንለው ነጥብ Centroid
ነው፡፡ ለምሳሌ የአራት መአዘን መሀል አሳይ ስትባል የምታሳየው
ቦታ
.
Centroid of a Volume = centroid of ቁመት - ርዝመትና
ወርድ ያለው አካል ወይም 3D object
Centroid of an Area = 2D ወይም ስፋትና ርዝመት ብቻ
ያለው አካል centroid
Centroid of a Line = ርዝመት ብቻ ያለው አካል centroid
ለምሳሌ ገመድ
.
Centroid ና Center of Gravity አንድ ነጥብ ላይ የሚሆኑት
አካሉ ሙሉ ለሙሉ አንድ ወጥ ከሆነ material ከተሰራ ነው -
density ከተለያየ ሁለቱ ነጥቦች የሚያርፉበት ቦታም ይለያያል፡፡
.
Center of Gravity = አንድ አካል በብዙ ጥቃቅን አካላት
የተመሰረተና የእነዚህ አካላት ስብስብ መሆኑ ይታወቃል፡፡ እናም
እነዚህ አካላት የየራሳቸው weight ወይም ክብደት አላቸው -
weighታቸውንም በአንድ weight መወከል እንችላለን ይህም
Resultant ይባላል፡፡ ይህ Resultant act የሚያደርግበት ቦታ
Center of Gravity ይባላል፡፡
.
Center of Mass = ከCenter of Gravity ጋር የሚለያየው በ
‘Weight’ ቦታ ‘Mass’ ስናስገባበት Center Of Mass
እናገኛለን (W = mg)
.
Centroid = የአንድ አካል ቅርፅ ላይ ( length , width &
height ) ላይ የሚመሰረት የአካሉ መሃከለኛ ቦታ ነው፡፡ እንዲሁ
በተለምዶ የአንድ አካል መሃል ነው የምንለው ነጥብ Centroid
ነው፡፡ ለምሳሌ የአራት መአዘን መሀል አሳይ ስትባል የምታሳየው
ቦታ
.
Centroid of a Volume = centroid of ቁመት - ርዝመትና
ወርድ ያለው አካል ወይም 3D object
Centroid of an Area = 2D ወይም ስፋትና ርዝመት ብቻ
ያለው አካል centroid
Centroid of a Line = ርዝመት ብቻ ያለው አካል centroid
ለምሳሌ ገመድ
.
Centroid ና Center of Gravity አንድ ነጥብ ላይ የሚሆኑት
አካሉ ሙሉ ለሙሉ አንድ ወጥ ከሆነ material ከተሰራ ነው -
density ከተለያየ ሁለቱ ነጥቦች የሚያርፉበት ቦታም ይለያያል፡፡
What is the value of tension 𝑇1 𝑎𝑛𝑑 𝑇2 in the figure shown above 👆🏾👆🏾👆🏾?
1. T1 = 14.33KN and T2 = 17.8KN
2. T1 = 28.87 KN and T2 = 14.33KN
3. T1 = 14.33KN and T2 = 28.87 KN
4. T1 = 17.87 KN and T2 = 28.87 KN
It’s preferable if you show us the solution on the discussion group @cotmp
አሰራሩንበ @cotmp ላይ ብታሳዩን ይመረጣል
We will soon come up with the solution
#mechanics #equilibrium
@etconp
1. T1 = 14.33KN and T2 = 17.8KN
2. T1 = 28.87 KN and T2 = 14.33KN
3. T1 = 14.33KN and T2 = 28.87 KN
4. T1 = 17.87 KN and T2 = 28.87 KN
It’s preferable if you show us the solution on the discussion group @cotmp
አሰራሩንበ @cotmp ላይ ብታሳዩን ይመረጣል
We will soon come up with the solution
#mechanics #equilibrium
@etconp
Ethio Construction Engineering via @like
What is the value of tension 𝑇1 𝑎𝑛𝑑 𝑇2 in the figure shown above 👆🏾👆🏾👆🏾? 1. T1 = 14.33KN and T2 = 17.8KN 2. T1 = 28.87 KN and T2 = 14.33KN 3. T1 = 14.33KN and T2 = 28.87 KN 4. T1 = 17.87 KN and T2 = 28.87 KN It’s preferable if you show us the solution…
Solution
Equilibrium position ላይ ነው ለመባል ፴ ቅድመሁታዎች ሊሟሉ ይገባል 👇🏾
A body to be in equilibrium position three conditions must be satisfied the conditions are stated below 👇🏾
➪ ΣF𝑥=0
➪ Σ F𝑦=0
➪ Σ M =0
The sum of Forces in the x- axis , forces in the y- axis and moment must be zero .
ΣF𝑦=0 ; 25 KN - T2sinθ =0
25KN - T2 0.86=0
25KN = T2 0.86
0.86 0.86
✔︎ T2 = 28.8 KN
ΣF𝑥 =T1- T2 cosθ =0
T1- 28.8 KN cos (60) =0
✔︎ T1 = 28.8 x 0.5 = 14.4 KN
Answer
✔︎ T1= 14.4 KN
✔︎ T2 = 28.8 KN
The Answer is option 3
@etconp
Equilibrium position ላይ ነው ለመባል ፴ ቅድመሁታዎች ሊሟሉ ይገባል 👇🏾
A body to be in equilibrium position three conditions must be satisfied the conditions are stated below 👇🏾
➪ ΣF𝑥=0
➪ Σ F𝑦=0
➪ Σ M =0
The sum of Forces in the x- axis , forces in the y- axis and moment must be zero .
ΣF𝑦=0 ; 25 KN - T2sinθ =0
25KN - T2 0.86=0
25KN = T2 0.86
0.86 0.86
✔︎ T2 = 28.8 KN
ΣF𝑥 =T1- T2 cosθ =0
T1- 28.8 KN cos (60) =0
✔︎ T1 = 28.8 x 0.5 = 14.4 KN
Answer
✔︎ T1= 14.4 KN
✔︎ T2 = 28.8 KN
The Answer is option 3
@etconp
Telegram
Ethio Construction Engineering
🔨 World Construction Engineering
Latest updates, tips, and tutorials on building, civil engineering, and construction in World.
Learn, build, and grow with us!
📨 @Philemona7 Or @ETCONpBOT
For Ad:- https://telega.io/c/etconp
Latest updates, tips, and tutorials on building, civil engineering, and construction in World.
Learn, build, and grow with us!
📨 @Philemona7 Or @ETCONpBOT
For Ad:- https://telega.io/c/etconp
👍1
This media is not supported in your browser
VIEW IN TELEGRAM
“This system consists of precast prestressed beam made of C50/60 - class concrete and dedicated floor hallow bricks that may be used to construct constructions of various heights and spans. The master floor system has the following floor construction heights: 14cm , 24cm ( the floor heights equals to the hallow brick height - no concrete overlay is needed ), 26cm , 28 cm and 30cm. “
Source:- Konbet poznan
እኛ ሀገርም 🇪🇹 ለ ኮንዶሚኒየም ቤቶች እንደዚህ 👆🏾አይነት precast intermediate beam ባለ 8 cm depth ያላው እንጠቀማለን። ሙሉ በሙሉ እንደዚህ አይነት system ባይሆንም....
ለመሆኑ primary beam እና secondary beam ምንድነው ልዩነቱ? Use @ctomp
What’s the difference between primary beam and secondary beam ? Use @cotmp
Points of consideration
➪ Transportation and logistics
➪ quality control (የጥራት ቁጥጥር)
➪ inspection is crucial for this system
እኛ ሀገር በአብዛኛው ጊዜ ይህ precast beam ችግር ሲሆን ይታያል
1. Beam’ ሁን ለመሸከም 3-4 ሰው(labour intensive)
2. ብዙ ጊዜ ተሰብረው site ላይ ወድቀው እናገኛለን
File size :- 9.0MB
የፋይል መጠን :-9.0MB
@etconp
Source:- Konbet poznan
እኛ ሀገርም 🇪🇹 ለ ኮንዶሚኒየም ቤቶች እንደዚህ 👆🏾አይነት precast intermediate beam ባለ 8 cm depth ያላው እንጠቀማለን። ሙሉ በሙሉ እንደዚህ አይነት system ባይሆንም....
ለመሆኑ primary beam እና secondary beam ምንድነው ልዩነቱ? Use @ctomp
What’s the difference between primary beam and secondary beam ? Use @cotmp
Points of consideration
➪ Transportation and logistics
➪ quality control (የጥራት ቁጥጥር)
➪ inspection is crucial for this system
እኛ ሀገር በአብዛኛው ጊዜ ይህ precast beam ችግር ሲሆን ይታያል
1. Beam’ ሁን ለመሸከም 3-4 ሰው(labour intensive)
2. ብዙ ጊዜ ተሰብረው site ላይ ወድቀው እናገኛለን
File size :- 9.0MB
የፋይል መጠን :-9.0MB
@etconp
@etconp part-9 visual art.pdf
251.2 KB
BASIC DESIGN AND VISUAL ARTS PART 9
Continued....................
7 Integral components used in the creation of a design: known as elements of art
0. Point
1. Line
2. Color
3. Form
4. Shape
5. Space
6. Texture
7. Value
Content
➪ How do we see color
𒊹︎The eye
𒊹︎CONES AND RODS IN RETINA
𒊹︎ Trichromats
➪ trichromats theory of color vision
➪ RBY color model ( red blue yellow)
To be continued.....
ይቀጥላል ....
#Visualarts
@etconp
Continued....................
7 Integral components used in the creation of a design: known as elements of art
0. Point
1. Line
2. Color
3. Form
4. Shape
5. Space
6. Texture
7. Value
Content
➪ How do we see color
𒊹︎The eye
𒊹︎CONES AND RODS IN RETINA
𒊹︎ Trichromats
➪ trichromats theory of color vision
➪ RBY color model ( red blue yellow)
To be continued.....
ይቀጥላል ....
#Visualarts
@etconp
Visual art quiz for architects
As you know we have presented you about the 7 Integral components used in the creation of a design 1. ___________is the element of art that is three dimensional and encloses volume. It includes height, width and depth.
As you know we have presented you about the 7 Integral components used in the creation of a design 1. ___________is the element of art that is three dimensional and encloses volume. It includes height, width and depth.
Anonymous Quiz
8%
Point
5%
Line
20%
Shape
26%
Form
4%
Area
37%
Volume
What are the Geosynthetics ?
Introduction
Types of geosynthetics
Raw materials
✔︎ wovens
✔︎ non-wovens
➪To read this short article tap instant view you can turn off your data
➪ ይህን ፅሁፍ ለማንበብ ‘instant view’ የሚለውን በመጫን በቀላሉ ሊያነቡ ይችላሉ
Instant view ማለት ፈጣን እይታ ማለት ነው instant view የሚለውን በነካችው ቅፅበት data አጥፍታችው የሚትፈልጉትን ማንበብ ትችላላችሁ ሞክሩት
https://telegra.ph/What-are-the-Geosynthetics-05-07
Introduction
Types of geosynthetics
Raw materials
✔︎ wovens
✔︎ non-wovens
➪To read this short article tap instant view you can turn off your data
➪ ይህን ፅሁፍ ለማንበብ ‘instant view’ የሚለውን በመጫን በቀላሉ ሊያነቡ ይችላሉ
Instant view ማለት ፈጣን እይታ ማለት ነው instant view የሚለውን በነካችው ቅፅበት data አጥፍታችው የሚትፈልጉትን ማንበብ ትችላላችሁ ሞክሩት
https://telegra.ph/What-are-the-Geosynthetics-05-07
Telegraph
What are the Geosynthetics
@etconp short article Introduction: Geo synthetics are artificial fabrics used in conjunction with soil or rock as an integral part of a man-made project. The two major groups in geosynthetics are geotextiles and geomembranes. While geotextile is a permeable…
👉🏿What do you say about this foundation?
👉🏿Do you think it’s adequate ?
👉🏿Do you think it’s time saving ?
👉🏿 what about cost
Use Discussion group @cotmp
👉🏿ይህ የምትመለከቱት መሰረት ተገቢ ነው ትላላችሁ?
👉🏿ጊዜ ቆጣቢ ይመስላችኋል?
👉🏿ወጪ ቆጣቢስ ይመስላችኋል?
Remember structure has to be safe first then we will think how to make it economical
@etconp
👉🏿Do you think it’s adequate ?
👉🏿Do you think it’s time saving ?
👉🏿 what about cost
Use Discussion group @cotmp
👉🏿ይህ የምትመለከቱት መሰረት ተገቢ ነው ትላላችሁ?
👉🏿ጊዜ ቆጣቢ ይመስላችኋል?
👉🏿ወጪ ቆጣቢስ ይመስላችኋል?
Remember structure has to be safe first then we will think how to make it economical
@etconp
👍2
Basic mechanics
What’s the resultant for these 👆🏾👆🏾 set of forces ?
1. 52.33 KN
2. 57.33 KN
3. 65.33 KN
4. 72.33 KN
Try it we will show you the solution
Participate
መልስ ይዘንላችሁ እንመጣለን ከነአሰራሩ
#mechanics #quiz #resultant
@etconp
What’s the resultant for these 👆🏾👆🏾 set of forces ?
1. 52.33 KN
2. 57.33 KN
3. 65.33 KN
4. 72.33 KN
Try it we will show you the solution
Participate
መልስ ይዘንላችሁ እንመጣለን ከነአሰራሩ
#mechanics #quiz #resultant
@etconp
Ethio Construction Engineering via @like
Basic mechanics What’s the resultant for these 👆🏾👆🏾 set of forces ? 1. 52.33 KN 2. 57.33 KN 3. 65.33 KN 4. 72.33 KN Try it we will show you the solution Participate መልስ ይዘንላችሁ እንመጣለን ከነአሰራሩ #mechanics #quiz #resultant @etconp
Solution for the question
F𝑥 = 0
➪ F𝑥= 30 x cos 30 ⁰ + 20 x cos 30 ⁰ +
20 x cos 60 ⁰ + 40 x cos 120 ⁰
✔︎ F𝑥 = 37. 32 KN
F𝑦 = 0
➪ F𝑦= 30 x sin30 ⁰ + 30 x sin30 ⁰
+ 20 x sin 60 ⁰+ 40 x sin 120 ⁰
✔︎ F𝑦= 61.96 KN
R= √ (F𝑥 +F𝑦)
✈︎ R = 72. 33 KN
So the answer is 4
The next quiz is about highway 🛣 Engineering be ready
#share
Invite your friends to this quiz fest
ጓደኞቻችሁን ወደዚህ ጋብዙ
@etconp
F𝑥 = 0
➪ F𝑥= 30 x cos 30 ⁰ + 20 x cos 30 ⁰ +
20 x cos 60 ⁰ + 40 x cos 120 ⁰
✔︎ F𝑥 = 37. 32 KN
F𝑦 = 0
➪ F𝑦= 30 x sin30 ⁰ + 30 x sin30 ⁰
+ 20 x sin 60 ⁰+ 40 x sin 120 ⁰
✔︎ F𝑦= 61.96 KN
R= √ (F𝑥 +F𝑦)
✈︎ R = 72. 33 KN
So the answer is 4
The next quiz is about highway 🛣 Engineering be ready
#share
Invite your friends to this quiz fest
ጓደኞቻችሁን ወደዚህ ጋብዙ
@etconp
Highway engineering I Quiz
If the stopping distance and average length of a vehicle 🚗 are 18 meters and 6 meters respectively, then the theoretical maximum capacity ( vehicle per hour) on traffic lane at a speed of 10 m/sec is
1. 1500
2. 2500
3. 2000
4. 3000
It’s preferable if you show us the step
አሰራር ብታሳዩን ይመረጣል
Invite your friends to this quiz fest
ጓደኞቻችሁን ወደዚህ የquiz ድግስ ጋብዙ
#share #highwayengineeringl
We will post the answer
አሰራሩን እናሳያችኋለን
@etconp
If the stopping distance and average length of a vehicle 🚗 are 18 meters and 6 meters respectively, then the theoretical maximum capacity ( vehicle per hour) on traffic lane at a speed of 10 m/sec is
1. 1500
2. 2500
3. 2000
4. 3000
It’s preferable if you show us the step
አሰራር ብታሳዩን ይመረጣል
Invite your friends to this quiz fest
ጓደኞቻችሁን ወደዚህ የquiz ድግስ ጋብዙ
#share #highwayengineeringl
We will post the answer
አሰራሩን እናሳያችኋለን
@etconp
Ethio Construction Engineering via @like
Highway engineering I Quiz If the stopping distance and average length of a vehicle 🚗 are 18 meters and 6 meters respectively, then the theoretical maximum capacity ( vehicle per hour) on traffic lane at a speed of 10 m/sec is 1. 1500 2. 2500 3. 2000…
Solution for this question
𝕋𝕚𝕞𝕖 𝕙𝕖𝕒𝕕𝕨𝕒𝕪
𝙷𝑡= 18meters + 6 meters
10 m/sec
𒊹︎Time headway’s (H𝑡) = 2.4 seconds
➪ Theoretical maximum capacity
= 3600 = 3600 = 1500 veh/ hour
H𝑡 2.4 sec
= 1500 vehicles / hour
The answer is 1
#share
#invite your friends
@etconp
𝕋𝕚𝕞𝕖 𝕙𝕖𝕒𝕕𝕨𝕒𝕪
𝙷𝑡= 18meters + 6 meters
10 m/sec
𒊹︎Time headway’s (H𝑡) = 2.4 seconds
➪ Theoretical maximum capacity
= 3600 = 3600 = 1500 veh/ hour
H𝑡 2.4 sec
= 1500 vehicles / hour
The answer is 1
#share
#invite your friends
@etconp
Telegram
Ethio Construction Engineering
🔨 World Construction Engineering
Latest updates, tips, and tutorials on building, civil engineering, and construction in World.
Learn, build, and grow with us!
📨 @Philemona7 Or @ETCONpBOT
For Ad:- https://telega.io/c/etconp
Latest updates, tips, and tutorials on building, civil engineering, and construction in World.
Learn, build, and grow with us!
📨 @Philemona7 Or @ETCONpBOT
For Ad:- https://telega.io/c/etconp
👍1