What type of bridge 🌉 is this ?
1. Beam bridge 🌉
2. Suspension bridge 🌉
3. Arch bridge 🌉
4. Cantilever bridge 🌉
Reference
👉🏿 https://t.me/ETCONP/2698
#bridge #quiz
@etconp
1. Beam bridge 🌉
2. Suspension bridge 🌉
3. Arch bridge 🌉
4. Cantilever bridge 🌉
Reference
👉🏿 https://t.me/ETCONP/2698
#bridge #quiz
@etconp
Ethio Construction Engineering via @like
Which one of the following supports can’t have zero deflection in vertical direction ? 1. Pin support 2. Roller support 3. Fixed support 4. Hinged support #support #quiz @etconp
Which one of the following supports can’t have zero deflection in vertical direction ?
Anonymous Quiz
15%
Pin support
26%
Roller support
43%
Fixed support
17%
Hinged support
Ethio Construction Engineering via @like
What type of bridge 🌉 is this ? 1. Beam bridge 🌉 2. Suspension bridge 🌉 3. Arch bridge 🌉 4. Cantilever bridge 🌉 Reference 👉🏿 https://t.me/ETCONP/2698 #bridge #quiz @etconp
The answer for this question is Arch bridge 🌉 3️⃣
Arch bridge is a bridge with abutment at each end shaped as curved arch. Arch bridges work by transferring the weight of the bridge and it’s old partially into horizontal thrust restrained by the abutment at either side.
@etconp
Arch bridge is a bridge with abutment at each end shaped as curved arch. Arch bridges work by transferring the weight of the bridge and it’s old partially into horizontal thrust restrained by the abutment at either side.
@etconp
Ethio Construction Engineering via @like
Which one of the following supports can’t have zero deflection in vertical direction ? 1. Pin support 2. Roller support 3. Fixed support 4. Hinged support #support #quiz @etconp
Answer for this question is hinged support 4️⃣
From the given support, only hinge can move from its initial position in the vertical direction. Fixed , roller and pinned supports do not behave as a hinge which is free to deflect in vertical direction.
[hibler]
@etconp
From the given support, only hinge can move from its initial position in the vertical direction. Fixed , roller and pinned supports do not behave as a hinge which is free to deflect in vertical direction.
[hibler]
@etconp
Site visitation
👆🏾👆🏾They dug out this footing to build another building in this site. Do you think this is appropriate to remove this footing ? For instance they could have used RCC(RC) jacketing.....
What’s your comment @cotmp
ይህን ህንፃ ለመገንባት መጀመሪያ የ ነበረውን footing ቆፍረው አወጡት ይህ ተገቢ ነው ትላላችሁ? እስኪ አስተያየታችሁን ፃፉልን @cotmp
@etconp
👆🏾👆🏾They dug out this footing to build another building in this site. Do you think this is appropriate to remove this footing ? For instance they could have used RCC(RC) jacketing.....
What’s your comment @cotmp
ይህን ህንፃ ለመገንባት መጀመሪያ የ ነበረውን footing ቆፍረው አወጡት ይህ ተገቢ ነው ትላላችሁ? እስኪ አስተያየታችሁን ፃፉልን @cotmp
@etconp
Forwarded from Ethio Construction Engineering (Fîłmøñ Łûël)
🔖አስደሳች ዜና ከ @ETCONp
.
👌ሰላም ውድ የቻናላችን ቤተሰቦች ላለፉት ወራት አንድ DIGITAL LIBRARY BOT ግንባታ ላይ ነበርን።
.
📚ይህም ዲጂታል ቤተመፃህፍት በውስጡ የ SOFTWARE SETUP, የ ARCH, COTM እና CIVIL መፅሀፍቶችን የያዘ ነው።
🚧ይህ የመጀመሪያ ምዕራፍ ግንባታ ሲሆን ለቀጣይ በአስተያየታችው መሰረት ብዙ ነገር ምናስተካክል ይሆናል።
👉ይህን link በመጫን ወደ ቤተመፃህፍቱ ልትሄዱ ትችላላችሁ።
👇👇👇👇👇👇
👉🏿 https://t.me/ETCONpDigitalLibrary_Bot
Good News from @ETCONP
👉🏿 For the last few months we have been developing digital library bot which consists ARCHITECTURE, Construction technology management and civil engineering books
👉🏿 This is the first phase of development base one tour request we will expand it In the future
👉🏿Tap the link below to access the digital library 📚👇🏾👇🏾👇🏾
👉🏿 @ETCONpDigitalLibrary_Bot
.
👌ሰላም ውድ የቻናላችን ቤተሰቦች ላለፉት ወራት አንድ DIGITAL LIBRARY BOT ግንባታ ላይ ነበርን።
.
📚ይህም ዲጂታል ቤተመፃህፍት በውስጡ የ SOFTWARE SETUP, የ ARCH, COTM እና CIVIL መፅሀፍቶችን የያዘ ነው።
🚧ይህ የመጀመሪያ ምዕራፍ ግንባታ ሲሆን ለቀጣይ በአስተያየታችው መሰረት ብዙ ነገር ምናስተካክል ይሆናል።
👉ይህን link በመጫን ወደ ቤተመፃህፍቱ ልትሄዱ ትችላላችሁ።
👇👇👇👇👇👇
👉🏿 https://t.me/ETCONpDigitalLibrary_Bot
Good News from @ETCONP
👉🏿 For the last few months we have been developing digital library bot which consists ARCHITECTURE, Construction technology management and civil engineering books
👉🏿 This is the first phase of development base one tour request we will expand it In the future
👉🏿Tap the link below to access the digital library 📚👇🏾👇🏾👇🏾
👉🏿 @ETCONpDigitalLibrary_Bot
Telegram
ETCONp Digital Library
ማሻሸያ እና አስተያየት ፃፋልን @Philemona7
👉ይህ የ ኢትየጵያዊያን የኮንስትራክሽን ስራ ባለሞያዎች ቻናል ዲጅታል ላይብረሪ ቦት ነው፡!
👉ይህ የ ኢትየጵያዊያን የኮንስትራክሽን ስራ ባለሞያዎች ቻናል ዲጅታል ላይብረሪ ቦት ነው፡!
जॉर्डनो ג׳ורדנו ጆርዳኖ جوردانو จอร์แดโน่ JORDANO Ιορδάνοςஜார்டானோ
Why is beam depth greater than it’s width ? ...... our channel member question The major role of beam is to resist moment generated by applied load or to resist the deflection again high moment on beam. Have you participate in this question 👇🏾👇🏾 ht…
Why is the beam depth is greater than its breadth ?
Simply this picture can explain it to you
@etconp
Simply this picture can explain it to you
@etconp
Ethio Construction Engineering via @like
RC QUIZ For balanced section of RCC(RC) beam, what is the area of steel required if the area of concrete 100 inch². 𝑓𝑐’= 4ksi and 𝑓𝑦= 60ksi. Where ksi= kilopound per square inch or 1000 pounds per square inch. 1. 2.6 inch² 2. 3.6 inch² 3. 4.6…
RC QUIZ
For balanced section of RCC(RC) beam, what is the area of steel required if the area of concrete 100 inch². 𝑓𝑐’= 4ksi and 𝑓𝑦= 60ksi. Where ksi= kilopound per square inch or 1000 pounds per square inch.
For balanced section of RCC(RC) beam, what is the area of steel required if the area of concrete 100 inch². 𝑓𝑐’= 4ksi and 𝑓𝑦= 60ksi. Where ksi= kilopound per square inch or 1000 pounds per square inch.
Anonymous Quiz
13%
2.6 inch²
39%
3.6 inch²
38%
4.6 inch²
10%
5.6 inch²
This media is not supported in your browser
VIEW IN TELEGRAM
Ethio Construction Engineering
Sticker
Take a rectangular stick or assume your phone and try to bend it along its flat surface. You will be able to do it. Because in this case it is relatively flexible.
A structural member is defined using two different criteria: Capacity and stiffness. They both are two different things. Capacity is the strength of the member to support loads before it fails and stiffness defines deformation of a member under a unit of applied load.
Now before going to that phone bending scenario, let us take a quick look at what is moment of resistance of section.
We all know what a bending moment is. A bending moment is a type of force which case "bending" of a structural member. It happens when you load a member perpendicular to its spanning direction.
Why not in the perpendicular direction? Because it is the most flexible in this direction and so easy to bend. Also mark that the depth of the iPhone in this direction is the lowest, that is equal to the thickness of the phone. Which means low moment capacity. Thus it is easy to kick this dude's butt. You can try it with any rectangular cross section object. About one axis it will be weaker than the other axis.
@etconp
A structural member is defined using two different criteria: Capacity and stiffness. They both are two different things. Capacity is the strength of the member to support loads before it fails and stiffness defines deformation of a member under a unit of applied load.
Now before going to that phone bending scenario, let us take a quick look at what is moment of resistance of section.
We all know what a bending moment is. A bending moment is a type of force which case "bending" of a structural member. It happens when you load a member perpendicular to its spanning direction.
Why not in the perpendicular direction? Because it is the most flexible in this direction and so easy to bend. Also mark that the depth of the iPhone in this direction is the lowest, that is equal to the thickness of the phone. Which means low moment capacity. Thus it is easy to kick this dude's butt. You can try it with any rectangular cross section object. About one axis it will be weaker than the other axis.
@etconp
Ethio Construction Engineering via @like
RC QUIZ For balanced section of RCC(RC) beam, what is the area of steel required if the area of concrete 100 inch². 𝑓𝑐’= 4ksi and 𝑓𝑦= 60ksi. Where ksi= kilopound per square inch or 1000 pounds per square inch. 1. 2.6 inch² 2. 3.6 inch² 3. 4.6…
Answer for this question 👆🏾👆🏾
𝐴s= 0.85 𝑥 𝑓𝑐’ 𝑥 𝐴𝑐
𝑓𝑦
𝐴s= 0.85 x 4000 x 100
60000
As= 5.6 inch²
So the answer is 4️⃣
@etconp
𝐴s= 0.85 𝑥 𝑓𝑐’ 𝑥 𝐴𝑐
𝑓𝑦
𝐴s= 0.85 x 4000 x 100
60000
As= 5.6 inch²
So the answer is 4️⃣
@etconp
Telegram
Ethio Construction Engineering
🔨 World Construction Engineering
Latest updates, tips, and tutorials on building, civil engineering, and construction in World.
Learn, build, and grow with us!
📨 @Philemona7 Or @ETCONpBOT
For Ad:- https://telega.io/c/etconp
Latest updates, tips, and tutorials on building, civil engineering, and construction in World.
Learn, build, and grow with us!
📨 @Philemona7 Or @ETCONpBOT
For Ad:- https://telega.io/c/etconp
FUNCTIONS OF FOUNDATIONS
Foundations serve the following purposes :-
1.Reduction of load intensity:- Foundations distribute the loads of the super-structure to a larger area so that the intensity of the load at its base (i.e., the total load divided by the total area)does not exceed the safe bearing capacity of the sub-soil. In the case of deep foundations it transmits the super imposed loads to the sub soil both through side friction as well as through end bearing
2.Even distribution of load:- Foundations distribute the non-uniform load of the super-structure evenly to be sub soil. For example two columns carrying unequal loads can have a combined footing which may transmit the load to sub soil evenly with uniform soil pressure. Due to this, differential settlements are minimised.
3. Provision of level surface:- Foundations provide levelled and hard surface over which the super structure can be built.
4. Lateral stability:- It anchors the super structure to the ground, thus imparting lateral stability to the super structure.The stability of the building, against sliding and overturning, due to horizontal forces (Such as wind, Earthquake etc.) is increased due to foundations.
5.Safety against undermining:- It provides the structural safety against undermining or scouring due to burrowing animals and flood water.
6.Protection against soil movements:- Special foundations measures prevents or minimises the distress (or cracks) in the super structure, due to expansion or contraction of the sub soil because of moisture movement in some problematic soils.
ESSENTIAL REQUIREMENTS OF A GOOD FOUNDATIONS :-
Foundations should be constructed to safety the following requirements:-
1.The foundations shall be constructed to sustain dead and imposed loads and to transmit these to the sub soil in such a way that pressure on it will not cause settlement which would impair the stability of the building or adjoining structures.
2.Foundation base should be rigid so that differential settlements are minimised, specially for the case when super imposed loads are not evenly distributed .
3.Foundations should be taken sufficiently deep to gaurd the building against damage or distress caused by swelling or shrinkage of the sub soil.
4. Foundations should be safely located that its performance may not be affected due to any unexpected future influence.
@etconp
Foundations serve the following purposes :-
1.Reduction of load intensity:- Foundations distribute the loads of the super-structure to a larger area so that the intensity of the load at its base (i.e., the total load divided by the total area)does not exceed the safe bearing capacity of the sub-soil. In the case of deep foundations it transmits the super imposed loads to the sub soil both through side friction as well as through end bearing
2.Even distribution of load:- Foundations distribute the non-uniform load of the super-structure evenly to be sub soil. For example two columns carrying unequal loads can have a combined footing which may transmit the load to sub soil evenly with uniform soil pressure. Due to this, differential settlements are minimised.
3. Provision of level surface:- Foundations provide levelled and hard surface over which the super structure can be built.
4. Lateral stability:- It anchors the super structure to the ground, thus imparting lateral stability to the super structure.The stability of the building, against sliding and overturning, due to horizontal forces (Such as wind, Earthquake etc.) is increased due to foundations.
5.Safety against undermining:- It provides the structural safety against undermining or scouring due to burrowing animals and flood water.
6.Protection against soil movements:- Special foundations measures prevents or minimises the distress (or cracks) in the super structure, due to expansion or contraction of the sub soil because of moisture movement in some problematic soils.
ESSENTIAL REQUIREMENTS OF A GOOD FOUNDATIONS :-
Foundations should be constructed to safety the following requirements:-
1.The foundations shall be constructed to sustain dead and imposed loads and to transmit these to the sub soil in such a way that pressure on it will not cause settlement which would impair the stability of the building or adjoining structures.
2.Foundation base should be rigid so that differential settlements are minimised, specially for the case when super imposed loads are not evenly distributed .
3.Foundations should be taken sufficiently deep to gaurd the building against damage or distress caused by swelling or shrinkage of the sub soil.
4. Foundations should be safely located that its performance may not be affected due to any unexpected future influence.
@etconp
General formula for concrete mix
Concrete Mix Ratio = 1:2:4
Let volume of concrete = Zm3
Then
a) Cement = 1/7 x zm3 x1400Kg/m3
x 1.3 shrinkage x 1.05 Wastage
= 273Kgs Z
= 0.19m3 Z
b) Sand = 2/7 x Zm3
x 1840Kg/m3
x 1.3 shrinkage x 1.05 Wastage
= 718Kgs Z
= 718/1840 m3 Z
= 0.39m3 Z
c) Gravel = 4/7 x Zm3 x 2250Kg/m3 x 1.3 shrinkage x 1.05 Wastage
= 1755 Kgs Z
= 0.95 m3 Z
Therfore for 1m3 concrete of C-20
With Mechanical Mix
Mix ratio 1:2:4
Cement = 275kg (5.5bags)
Sand = 718Kg (0.39m3)
Gravel = 1755Kgs (0.78m3)
Water = 110 liters
Assuming
30% Shrinkage
5% Wastage
For Mechanical Mix W/C = 0.4 – 0.5
Hand Mix W/C = 0.4 – 0.65
Note: Hand Mix shall only be allowed for class II concrete, and shall not be
allowed for concrete of class c-20 and above.
@etconp
Concrete Mix Ratio = 1:2:4
Let volume of concrete = Zm3
Then
a) Cement = 1/7 x zm3 x1400Kg/m3
x 1.3 shrinkage x 1.05 Wastage
= 273Kgs Z
= 0.19m3 Z
b) Sand = 2/7 x Zm3
x 1840Kg/m3
x 1.3 shrinkage x 1.05 Wastage
= 718Kgs Z
= 718/1840 m3 Z
= 0.39m3 Z
c) Gravel = 4/7 x Zm3 x 2250Kg/m3 x 1.3 shrinkage x 1.05 Wastage
= 1755 Kgs Z
= 0.95 m3 Z
Therfore for 1m3 concrete of C-20
With Mechanical Mix
Mix ratio 1:2:4
Cement = 275kg (5.5bags)
Sand = 718Kg (0.39m3)
Gravel = 1755Kgs (0.78m3)
Water = 110 liters
Assuming
30% Shrinkage
5% Wastage
For Mechanical Mix W/C = 0.4 – 0.5
Hand Mix W/C = 0.4 – 0.65
Note: Hand Mix shall only be allowed for class II concrete, and shall not be
allowed for concrete of class c-20 and above.
@etconp
Telegram
Ethio Construction Engineering
🔨 World Construction Engineering
Latest updates, tips, and tutorials on building, civil engineering, and construction in World.
Learn, build, and grow with us!
📨 @Philemona7 Or @ETCONpBOT
For Ad:- https://telega.io/c/etconp
Latest updates, tips, and tutorials on building, civil engineering, and construction in World.
Learn, build, and grow with us!
📨 @Philemona7 Or @ETCONpBOT
For Ad:- https://telega.io/c/etconp
Pinnacle tower 🇰🇪
This is a skyscraper 🏙 under construction in the capital of Kenya Nairobi 🇰🇪. The construction started in 2017 and its estimated to be completed in 2023.
➪ Height:- 320 meters
➪ floor count :- 46 the shorter 70 the taller
➪ status :- under construction
➪ cost :- Sh20 billion (Est)
Grounds:- 2.5 acres (1.0 hectare)
Architecture firm:- Archgroup Consultants
Developer:- White Lotus Group Jabavu Village
Engineer:- Meinhardt
Quantity surveyor:- BECS Consultancy
Main contractor :- China State Construction Engineering Corporation
When completed, the skyscraper is expected to become the tallest building in Africa, and the third tallest building in the Southern Hemisphere, at 70 stories and over 1,000 feet (300 m) in height.
CBE headquarter will be the 5th tallest tower in Africa
We wish you a wonderful night
@etconp
This is a skyscraper 🏙 under construction in the capital of Kenya Nairobi 🇰🇪. The construction started in 2017 and its estimated to be completed in 2023.
➪ Height:- 320 meters
➪ floor count :- 46 the shorter 70 the taller
➪ status :- under construction
➪ cost :- Sh20 billion (Est)
Grounds:- 2.5 acres (1.0 hectare)
Architecture firm:- Archgroup Consultants
Developer:- White Lotus Group Jabavu Village
Engineer:- Meinhardt
Quantity surveyor:- BECS Consultancy
Main contractor :- China State Construction Engineering Corporation
When completed, the skyscraper is expected to become the tallest building in Africa, and the third tallest building in the Southern Hemisphere, at 70 stories and over 1,000 feet (300 m) in height.
CBE headquarter will be the 5th tallest tower in Africa
We wish you a wonderful night
@etconp
👍1
Forwarded from Ethio Construction Engineering
👉የአርማታ ብረት በሜትር ምን ያህል ይመዝናል? @COTMp
.
⏩ለኮንስትራክሽን ግብዐት የምንጠቀማቸው የአርማታ ብረት በቅርፃቸው በሁለት ይከፈላሉ
1. ልሙጥ ብረት(Mild Steel or plain rebar)
2. ባለ ክርክር/አርማታ ብረት(Deformed steel rebar)
➡በጥንካሬ ደረጃ ደግሞ በስፋት Grade 60 እና Grade 40
በመባል ይለያሉ ይህም ውጥረታዊ ሀይል/tensile strength/ በመቌቌም አቅማቸው ነው።
*Grade 40=275.79MPa yield strength ሲኖረው
*Grade 60=413.68MPa yield strength ይኖረዋል።
.
ለሁሉም እንዲዳረስ ፖስቶቹን SHARE አድርጉልን።
👇👇👇👇👇
Join for more updates via the link below;
t.me/COTMp
👆👆👆👆👆
.
⏩ለኮንስትራክሽን ግብዐት የምንጠቀማቸው የአርማታ ብረት በቅርፃቸው በሁለት ይከፈላሉ
1. ልሙጥ ብረት(Mild Steel or plain rebar)
2. ባለ ክርክር/አርማታ ብረት(Deformed steel rebar)
➡በጥንካሬ ደረጃ ደግሞ በስፋት Grade 60 እና Grade 40
በመባል ይለያሉ ይህም ውጥረታዊ ሀይል/tensile strength/ በመቌቌም አቅማቸው ነው።
*Grade 40=275.79MPa yield strength ሲኖረው
*Grade 60=413.68MPa yield strength ይኖረዋል።
.
ለሁሉም እንዲዳረስ ፖስቶቹን SHARE አድርጉልን።
👇👇👇👇👇
Join for more updates via the link below;
t.me/COTMp
👆👆👆👆👆
Ethio Construction Engineering via @like
Surveying quiz Survey which determines property line (property boundaries) is called __? 1. City survey 2. Cadastral survey 3. Land survey 4. Topographic survey #quiz #survey @etconp
Surveying quiz
Survey which determines property line (property boundaries) is called __?
Survey which determines property line (property boundaries) is called __?
Anonymous Quiz
8%
City survey
59%
Cadastral survey
23%
Land survey
10%
Topographic survey
Ethio Construction Engineering via @like
Surveying quiz Survey which determines property line (property boundaries) is called __? 1. City survey 2. Cadastral survey 3. Land survey 4. Topographic survey #quiz #survey @etconp
👆🏾👆🏾The answer for this question is cadastral surveying 2️⃣
Cadastral surveying is the sub-field of cadastre and surveying that specialises in the establishment and re-establishment of real property boundaries. It is an important component of the legal creation of properties. A cadastral surveyor must apply both the spatial-measurement principles of general surveying and legal principles such as respect of neighboring titles.
@etconp
Cadastral surveying is the sub-field of cadastre and surveying that specialises in the establishment and re-establishment of real property boundaries. It is an important component of the legal creation of properties. A cadastral surveyor must apply both the spatial-measurement principles of general surveying and legal principles such as respect of neighboring titles.
@etconp