Ethio Construction Engineering
32.3K subscribers
6.28K photos
359 videos
1.99K files
3.35K links
🔨 World Construction Engineering
Latest updates, tips, and tutorials on building, civil engineering, and construction in World.
Learn, build, and grow with us!

📨 @Philemona7 Or @ETCONpBOT

For Ad:- https://telega.io/c/etconp
Download Telegram
FUNCTIONS OF FOUNDATIONS

Foundations serve the following purposes :-
1.Reduction of load intensity:- Foundations distribute the loads of the super-structure to a larger area so that the intensity of the load at its base (i.e., the total load divided by the total area)does not exceed the safe bearing capacity of the sub-soil. In the case of deep foundations it transmits the super imposed loads to the sub soil both through side friction as well as through end bearing
2.Even distribution of load:- Foundations distribute the non-uniform load of the super-structure evenly to be sub soil. For example two columns carrying unequal loads can have a combined footing which may transmit the load to sub soil evenly with uniform soil pressure. Due to this, differential settlements are minimised.
3. Provision of level surface:- Foundations provide levelled and hard surface over which the super structure can be built.
4. Lateral stability:- It anchors the super structure to the ground, thus imparting lateral stability to the super structure.The stability of the building, against sliding and overturning, due to horizontal forces (Such as wind, Earthquake etc.) is increased due to foundations.
5.Safety against undermining:- It provides the structural safety against undermining or scouring due to burrowing animals and flood water.
6.Protection against soil movements:- Special foundations measures prevents or minimises the distress (or cracks) in the super structure, due to expansion or contraction of the sub soil because of moisture movement in some problematic soils.

ESSENTIAL REQUIREMENTS OF A GOOD FOUNDATIONS :-
Foundations should be constructed to safety the following requirements:-
1.The foundations shall be constructed to sustain dead and imposed loads and to transmit these to the sub soil in such a way that pressure on it will not cause settlement which would impair the stability of the building or adjoining structures.
2.Foundation base should be rigid so that differential settlements are minimised, specially for the case when super imposed loads are not evenly distributed .
3.Foundations should be taken sufficiently deep to gaurd the building against damage or distress caused by swelling or shrinkage of the sub soil.
4. Foundations should be safely located that its performance may not be affected due to any unexpected future influence.

@etconp
👉የአርማታ ብረት በሜትር ምን ያህል ይመዝናል? @COTMp
.
⏩ለኮንስትራክሽን ግብዐት የምንጠቀማቸው የአርማታ ብረት በቅርፃቸው በሁለት ይከፈላሉ
1. ልሙጥ ብረት(Mild Steel or plain rebar)
2. ባለ ክርክር/አርማታ ብረት(Deformed steel rebar)
➡በጥንካሬ ደረጃ ደግሞ በስፋት Grade 60 እና Grade 40
በመባል ይለያሉ ይህም ውጥረታዊ ሀይል/tensile strength/ በመቌቌም አቅማቸው ነው።
*Grade 40=275.79MPa yield strength ሲኖረው
*Grade 60=413.68MPa yield strength ይኖረዋል።
.
ለሁሉም እንዲዳረስ ፖስቶቹን SHARE አድርጉልን።
👇👇👇👇👇
Join for more updates via the link below;
t.me/COTMp
👆👆👆👆👆
Surveying quiz

Survey which determines property line (property boundaries) is called __?

1. City survey

2. Cadastral survey

3. Land survey

4. Topographic survey

#quiz #survey

@etconp
Ethio Construction Engineering via @like
Surveying quiz Survey which determines property line (property boundaries) is called __? 1. City survey 2. Cadastral survey 3. Land survey 4. Topographic survey #quiz #survey @etconp
Surveying quiz

Survey which determines property line (property boundaries) is called __?
Anonymous Quiz
8%
City survey
59%
Cadastral survey
23%
Land survey
10%
Topographic survey
Ethio Construction Engineering via @like
Surveying quiz Survey which determines property line (property boundaries) is called __? 1. City survey 2. Cadastral survey 3. Land survey 4. Topographic survey #quiz #survey @etconp
👆🏾👆🏾The answer for this question is cadastral surveying 2️⃣

Cadastral surveying
is the sub-field of cadastre and surveying that specialises in the establishment and re-establishment of real property boundaries. It is an important component of the legal creation of properties. A cadastral surveyor must apply both the spatial-measurement principles of general surveying and legal principles such as respect of neighboring titles.

@etconp
Just for discussion:

For defining of earthquake loading some designers are under doubt about user coefficient and response spectrum. What about your view from different requirements......

@etconp
Sunrise Kempinski Hotel

Official name :- Sunrise Kempinski Hotel

Status :- completed

Country :- China 🇨🇳

Building purpose :- HOTEL 🏨

Construction started:- 2012 GC

Completion :- 2014 GC

Owner :- Beijing Enterprises International Conference Metropolis Real Estate Co., Ltd.

Architectural design structural design and MEP design :- Shanghai Huadu Architect Design Company

Contractor:- Beijing Urban Construction Group Co., Ltd

Height :- 77 meters

Floor above the ground :- 20

Floors below the ground:- 2

Built up area :- 35,582 m²

@etconp
👉ስለ ብሎኬት @COTMp
.
⏩Hollow Concret Block (HCB) ወይም የግድግዳ ብሎኬት/Wall HCB/ በመባል ይታወቃል።
*የብሎኬት ምርት ሲደረግ ጠቀሜታው ለሁለት ጉዳይ ነው
1. ሸክም መቌቌም የሚችል/Load Bearing/
2. ሸክም መቌቌም የማይችል /Non-Load Bearing/
*ይሄንን መሰረት ያደረገም የደረጃ ክፍፍል/Class/ ይኖራቸዋል።
*ሸክም መቌቌም የሚችሉት ብሎኬቶች "ክላስ ኤ እና ቢ" /
Class A and B/ በመባል ሲመደቡ ሸክም መቌቌም
የማይችሉት የብሎኬቶች ደግሞ "ክላስ ሲ" /Class C/ በመባል
ይመደባሉ።
➡ብሎኬት በተለምዶ በመጠናቸው ባለ10፣ ባለ15 እና ባለ 20 በመባል ይለያሉ::
ርዝመት x ስፋት x ቁመት/ Length x width x depth/
ማለትም Standard Dimenssion
*40x20x20cm
*40x15x20cm
*40x10x20cm
➡እያንዳንዱ ብሎኬት ሸክም የመቌቌም አቅማቸው
በሜጋ ፓስካል(Mpa) ይለካል ከዚህ በላይ 👆 በምስል አስደግፈናል።
*Note:
1 kilogram per square centimetre = 0.0981 mega pascal

*Class A=3.8mpa
*Class B=3.2mpa
*Class C=1.8mpa
.
⚡ለሁሉም እንዲዳረስ ፖስቶቹን SHARE አድርጉልን።
👍1
Key brick or Keystone: The voussoir located at the crown of the arch. Also called the key.

Spring Line: A horizontal line which intersects the springing.

Extrados: The curve which bounds the upper edge of the arch.

Intrados: The curve which bounds the lower edge of the arch. The distinction between soffit and intrados is that the intrados is a line, while the soffit is a surface.

The point at which the bisector crosses the centre line is the centre or striking point for the segmental arch

Pier or span: The horizontal clear dimension between abutments.

Voussoir: One masonry unit of an arch.

Regarding arch brick construction we come up with some 📹


@etconp
Components of Project cost

♦️ Indirect cost :- Outage loss + Overheads

♦️ Direct project cost :- These include labour cost, material cost, equipment cost etc.

♦️ Normal time :- Normal time is the standard time that an estimator would usually allow for an activity.

♦️ Crash time :- Crash time is the minimum possible time which an activity can be completed by employing extra resources

♦️ Normal cost :- This is direct cost required to complete the activity in normal time duration.

♦️ Crash cost :- This is direct cost corresponding to the completion of the activity within crash time.

Join us @ETCONP
Instrument used in surveying👇
♦️ Clinometer:- measuring angles of slopes
♦️subtence bar:- measure horizontal distance
♦️Box sextant:- measuring horizontal angle
♦️Planimeter:- measuring area on map
♦️pentagraph:- enlarging or reducing area on map
♦️line Ranger:- ranging a chain line
♦️Hand level:- Making contour & Cross section of preliminary work
♦️Ceylon ghat tracer:- Measuring angles of slopes & setting out grade contours.

@ETCONP
_*📌▪BENEFITS OF USING PLASTIC FORMWORKS IN CONCRETE CONSTRUCTION▪*_


Plastic formworks in concrete construction are used to retain newly arranged concrete in place to provide adequate strength. Formworks facilitate to manage concrete efficiently and produce different types of shapes and forms.

Various types of materials like timber, steel, and aluminum are applied to develop formworks. Plastic is considered as best for formworks in relation to other materials in terms of strength, cost-effectiveness, and adaptability.

Sufficient time is required to develop the formworks. Formworks comprise 20 to 25% of the total cost of the structure. The security, cost, quality, and speed of a construction work mainly depend on formworks.

*Benefits of Plastic Formworks in Concrete Construction*

Plastic formworks provide various benefits like longevity, cost, and flexibility. Formworks consume huge labor force and total cost of the project. It is recommended that a formwork system should be cost-effective and assembled, disintegrated and managed smoothly by labor.


*The plastic formworks provide the following benefits to the concrete construction:*

Grading of Aggregates

Economical

Labor-friendly

Eco friendly

Low maintenance

Flexible


*Plastic Formwork System*

Certain grade plastics are used to build up formworks. There are not any chemical reactions among poured material and the plastic form. No patch on the surface of the reinforce concrete element exists.

*Leakages*

Resist leakages with water or newly arranged concrete from various parts of the form by fitting different parts of the system accurately.

Labor-friendly system
Plastic formworks are considered very labor-friendly system. It accommodates and plugs smoothly and significantly lightweight with regards to other types of formwork systems.

*Nailing and oiling*

Nailing and oiling plates are not necessary. Auto-leveling of plugging system can retain plates level automatically. It takes fewer time to install and disassemble.

*Cleaning*

Plastic forms can be cleansed with water without difficulty. Plastic forms can be broken due to handling in an inefficient manner as well as use of low voltage hot air gun for sealing.

Plastic forms can be easily reprocessed and they are eco-friendly to minimize handling time and great re-usability index.

For more concepts of civil engineering

Join us on telegram:- @ETCONP

Follow us on Instagram:- @etconp
👉ፎርምወርክ/Formwork/ @COTMp
➡በምን ያህል ቀን ማፍረስ ይቻላል?👇
.
⏩ ለቌሚ ፎርምወርክ 16ሰዓት
⏩ ለወለል እና ደረጃ /ሶሌታ/ ፎርምወረክ 21 ቀን
⏩ ተጨማሪ ለቢም/beam/ እና ወለል/slab/ ድጋፍ የሚገባ
14ቀን
⚡ የፎርም ወርክ ክፍያን በተመለከተ ባትኮዳ/Batcoda/ ከዚህ በታች የተዘረዘሩትን ነጥቦች ይጠቅሳል።
1. ከ 0.25ካ.ሜ በታች የሆነ ክፍት/opening/ ፎርሞርክ ክፍያ
ላይ ሊቀነስ አይገባም።
2. በተለየ ሁኔታ ካልተጠቀሰ በስተቀር በካ. ሜ ሊለካ ይገባል።
3. የወለል ጠርዝ፣ የደረጃ መወጣጫ እና የጎን ፎርምወረክ
ጥልቀቱን በመጥቀስ በሜትር ሊለኩ ይገባል።
.
🚩ለሁሉም እንዲዳረስ ፖስቶቹን SHARE አድርጉልን።
Forwarded from Ethio Construction Engineering (Fîłmøñ Łûël)
🔖አስደሳች ዜና ከ @ETCONp
.
👌ሰላም ውድ የቻናላችን ቤተሰቦች ላለፉት ወራት አንድ DIGITAL LIBRARY BOT ግንባታ ላይ ነበርን።
.
📚ይህም ዲጂታል ቤተመፃህፍት በውስጡ የ SOFTWARE SETUP, የ ARCH, COTM እና CIVIL መፅሀፍቶችን የያዘ ነው።

🚧ይህ የመጀመሪያ ምዕራፍ ግንባታ ሲሆን ለቀጣይ በአስተያየታችው መሰረት ብዙ ነገር ምናስተካክል ይሆናል።

👉ይህን link በመጫን ወደ ቤተመፃህፍቱ ልትሄዱ ትችላላችሁ።
👇👇👇👇👇👇
👉🏿 https://t.me/ETCONpDigitalLibrary_Bot

Good News from @ETCONP

👉🏿 For the last few months we have been developing digital library bot which consists ARCHITECTURE, Construction technology management and civil engineering books

👉🏿 This is the first phase of development base one tour request we will expand it In the future

👉🏿Tap the link below to access the digital library 📚👇🏾👇🏾👇🏾

👉🏿 @ETCONpDigitalLibrary_Bot
Siporex precast wall

STEEL REINFORCED  WALL PANELS

WV are reinforced units, for load bearing applications as either external or internal walls in a wide variety of low and medium rise buildings. They can also be used as non-load bearing cladding for steel or concrete framed structures. They may have single mat or double mat reinforcements depending on the structural requirements.

Siporex floor/roof slabs are reinforced aerated concrete products which are produced in accordance with international standards.

Siporex slabs attain their design strengths during the high-pressure steam curing process in the autoclaves. Thus, after delivery, slabs can be erected immediately within a very short period and ready for occupancy use.

Submerged beam is one that has the same elevation as the top of the slab as well as the bottom of the slab. In most cases a submerged beam is called hidden.

@etconp
👍1