Forwarded from Ethio Construction Engineering (Fîłmøñ Łûël)
👉Today Tip @COTMp
.
➡ በ አንድ ሜትር ካሬ ምን ያህል ብሎኬት እንጠቀማለን??
⏩የብሎኬት👇
▶ ስፋት =0.4ሜ
▶ቁመት =0.2ሜ
=1/(0.4*0.2)
=12.5
=~13
🚩ስለዚህ በ አንድ ሜትር ካሬ 13 ፍሬ ብሎኬት እንጠቀማለን ማለት ነው።
.
➡ በ አንድ ሜትር ካሬ ምን ያህል ብሎኬት እንጠቀማለን??
⏩የብሎኬት👇
▶ ስፋት =0.4ሜ
▶ቁመት =0.2ሜ
=1/(0.4*0.2)
=12.5
=~13
🚩ስለዚህ በ አንድ ሜትር ካሬ 13 ፍሬ ብሎኬት እንጠቀማለን ማለት ነው።
Ethio Construction Engineering
👉ይህ የምትመለከቱት ህንፃ አዲስ አበባ ከጎማ ቁጠባ (ጥቂር አንበሳ) ወደ ባልቻ በሚወስደው መንገድ ዳር የተገነባ አዲስ ሕንፃ ነው። . ✍ስለዚህ ህንፃ ሀሳብ እና አስተያየትዎ @COTMp ፃፉልን። @etconp
The guiding principles governing a bulding design based on eurocode 1998-1:2003 are
👉Structural simplicity
👉Uniformity symmetry and redundancy
👉Tosrional resisitance and stiffness
👉Diaphragmatic behaviour at story level
👉Adequate foundation.
For the purpose of seismic desgn, buildung structure are categorized into being regular and non-regular
Criteria describing regularty in plan and in elevation are given in Eurocode 1998 part 1 PrENl998-1:2003 4. 2. 3. 2 and 4. 2. 3. 3
Therefore the picture in the building seem not to satisfy the criteria in regularty in plan.
➡️ The slenderness λ=Lmax/Lmin
Of the building shall not be higher than 4 where Lmax and Lmin are respectively the larger and the smaller in plan dimension of the building measured in orthogonal directions.
Thank you 🙏 @Yo_Dty
Join us on telegram:- @etconp
Follow us on Instagram:- @etconp
👉Structural simplicity
👉Uniformity symmetry and redundancy
👉Tosrional resisitance and stiffness
👉Diaphragmatic behaviour at story level
👉Adequate foundation.
For the purpose of seismic desgn, buildung structure are categorized into being regular and non-regular
Criteria describing regularty in plan and in elevation are given in Eurocode 1998 part 1 PrENl998-1:2003 4. 2. 3. 2 and 4. 2. 3. 3
Therefore the picture in the building seem not to satisfy the criteria in regularty in plan.
➡️ The slenderness λ=Lmax/Lmin
Of the building shall not be higher than 4 where Lmax and Lmin are respectively the larger and the smaller in plan dimension of the building measured in orthogonal directions.
Thank you 🙏 @Yo_Dty
Join us on telegram:- @etconp
Follow us on Instagram:- @etconp
Telegram
Ethio Construction Engineering
🔨 World Construction Engineering
Latest updates, tips, and tutorials on building, civil engineering, and construction in World.
Learn, build, and grow with us!
📨 @Philemona7 Or @ETCONpBOT
For Ad:- https://telega.io/c/etconp
Latest updates, tips, and tutorials on building, civil engineering, and construction in World.
Learn, build, and grow with us!
📨 @Philemona7 Or @ETCONpBOT
For Ad:- https://telega.io/c/etconp
MORTAR, CEMENT AND SAND FOR RENDERING AND FLOORING
➡️Rendering
Cement mortar rendering on walls per 10 square meters with 20% wastage mix proportion 1:3
1) Mortar = 0.06m3 /10m2
1.1) Cement = 27.56 Kgs
1.2) Sand = 0.06m3
➡️Flooring
a) Terrazo tile (cement tile) flooring bedded in cement mortar 1:4
1) Terrazzo tile (cement tile) with 2% wastage
Size 20 x 20 = 26pcs/m2
2) 2.5cm thick mortar with 10% wastage for laying.
2.1) Cement = 10.12Kgs /m2
2.2) Sand =0.0275m3/m2
3) Mortar 1:3 for grouting with 20% wastage = 0.001m3 /m2
3.1) Cement = 0.46kgs/m2
3.2) Sand =0.001m3 /m2
b) Cement screed flooring with an average thickness of 2.5cm
1) Mortar 1:3 with 20% wastage = 0.03m3 /m2
1.1) Cement = 13.78kgs/m2
1.2) Sand = 0.03m3 /m2
c) 2cm thick marble slate flooring bedded in cement sand screed 1:4
1) Marble slate with 2% wastage = 1.02m2 /m2
2) 2.5cm thick mortar with 10% wastage = 0.027m3 /m2
2.1) cement = 10.12kgs/m2
2.2) Sand =0.029m3/m2
#quantityandrateanalysis
@etconp
➡️Rendering
Cement mortar rendering on walls per 10 square meters with 20% wastage mix proportion 1:3
1) Mortar = 0.06m3 /10m2
1.1) Cement = 27.56 Kgs
1.2) Sand = 0.06m3
➡️Flooring
a) Terrazo tile (cement tile) flooring bedded in cement mortar 1:4
1) Terrazzo tile (cement tile) with 2% wastage
Size 20 x 20 = 26pcs/m2
2) 2.5cm thick mortar with 10% wastage for laying.
2.1) Cement = 10.12Kgs /m2
2.2) Sand =0.0275m3/m2
3) Mortar 1:3 for grouting with 20% wastage = 0.001m3 /m2
3.1) Cement = 0.46kgs/m2
3.2) Sand =0.001m3 /m2
b) Cement screed flooring with an average thickness of 2.5cm
1) Mortar 1:3 with 20% wastage = 0.03m3 /m2
1.1) Cement = 13.78kgs/m2
1.2) Sand = 0.03m3 /m2
c) 2cm thick marble slate flooring bedded in cement sand screed 1:4
1) Marble slate with 2% wastage = 1.02m2 /m2
2) 2.5cm thick mortar with 10% wastage = 0.027m3 /m2
2.1) cement = 10.12kgs/m2
2.2) Sand =0.029m3/m2
#quantityandrateanalysis
@etconp
👍1
The number of independent equations to be satisfied for static equilibrium of a plane structure is
Anonymous Quiz
12%
1
22%
2
60%
3
5%
6
Ethio Construction Engineering
The number of independent equations to be satisfied for static equilibrium of a plane structure is
Answer for this question 👆🏾👆🏾
1. For a two dimensional (2D) or plane frame The total number of equilibrium equations = 3
(ΣFx = 0, ΣFy = 0, ΣMxy = 0)
(If x -y plane is considered)
2. For a three dimensional (3D) or space frame
The total number of equilibrium equations = 6
( ΣFx = 0, ΣFy =0, ΣFz 0, ΣMxy = 0, ΣMyz = 0, ΣMzx = 0)
Join us on telegram:- @etconp
Follow us on Instagram:- @etconp
1. For a two dimensional (2D) or plane frame The total number of equilibrium equations = 3
(ΣFx = 0, ΣFy = 0, ΣMxy = 0)
(If x -y plane is considered)
2. For a three dimensional (3D) or space frame
The total number of equilibrium equations = 6
( ΣFx = 0, ΣFy =0, ΣFz 0, ΣMxy = 0, ΣMyz = 0, ΣMzx = 0)
Join us on telegram:- @etconp
Follow us on Instagram:- @etconp
Telegram
Ethio Construction Engineering
🔨 World Construction Engineering
Latest updates, tips, and tutorials on building, civil engineering, and construction in World.
Learn, build, and grow with us!
📨 @Philemona7 Or @ETCONpBOT
For Ad:- https://telega.io/c/etconp
Latest updates, tips, and tutorials on building, civil engineering, and construction in World.
Learn, build, and grow with us!
📨 @Philemona7 Or @ETCONpBOT
For Ad:- https://telega.io/c/etconp
Ethio Construction Engineering
What is the difference between C30 concrete and M30 concrete? And what does PSI mean? እኛ እንደምናውቀው የ concrete grade የሚገለፀው C-5,C-20, C-30...... እየተባለ ነው። ግን እዚህ ምስል ላይ የምትመለከቱት 👆🏾👆🏾.... M5,M30, M30 እያለ ነው። ❓ምንድንነው የሁለቱ ልዩነት ሌላኛው እዚህ ምስል ላይ PSI ይላል። …
As per IS 456,an environmental exposure is divided in to 5
Mild
Concrete surfaces protected against weather or aggressive conditions, except those situated in coastal areas
Moderate
Concrete surface sheltered from severe rain or freezing whilst wet; concrete exposed to condensation and rain, concrete continuously under water; concrete in contact or buried under non-aggressive soil/ground water; concrete surfaces sheltered from saturated salt air in coastal area
Severe
Concrete surfaces exposed to severe rain, alternate wetting and drying or occasional freezing whilst wet or severe condensation; concrete completely immersed in sea water; concrete exposed to coastal environment
Very Severe
Concrete surfaces exposed to sea water spray, corrosive fumes or severe freezing conditions whilst wet; concrete in contact with or buried under aggressive sub-soil/ground water
Extreme
Surfaces of members in tidal zone; members in direct contact with liquid/solid aggressive chemicals
@etconp
Mild
Concrete surfaces protected against weather or aggressive conditions, except those situated in coastal areas
Moderate
Concrete surface sheltered from severe rain or freezing whilst wet; concrete exposed to condensation and rain, concrete continuously under water; concrete in contact or buried under non-aggressive soil/ground water; concrete surfaces sheltered from saturated salt air in coastal area
Severe
Concrete surfaces exposed to severe rain, alternate wetting and drying or occasional freezing whilst wet or severe condensation; concrete completely immersed in sea water; concrete exposed to coastal environment
Very Severe
Concrete surfaces exposed to sea water spray, corrosive fumes or severe freezing conditions whilst wet; concrete in contact with or buried under aggressive sub-soil/ground water
Extreme
Surfaces of members in tidal zone; members in direct contact with liquid/solid aggressive chemicals
@etconp
The coefficient if compressibility of soil is the ratio of :__________?
Anonymous Quiz
20%
Stress to strain
28%
Porosity to void ratio
34%
Void ratio to porosity
18%
Strain to stress
Ethio Construction Engineering
The coefficient if compressibility of soil is the ratio of :__________?
Answer for this question 👆🏾👆🏾
Strain to strain unlike strength of material
Soil compressibility is the capability of a soil to decrease in volume when subjected to a mechanical load. The process that describes the decrease in soil volume (soil densification) under an externally applied load is called compression. ... Simply, consolidation refers to compression of saturated soil.
The practical significance of the soil‐compressibility determination lies in describing the ease with which the soils are susceptible to soil compaction. Laboratory tests for measuring soil compressibility are normally conducted either in a consolidometer or in a triaxial compression cell. This chapter focuses on one‐dimensional compression in a consolidometer. In the compressibility test using a consolidometer, only measurements of volume change of the soil specimens are desired; therefore, corrections must be applied for any significant deformation caused by the compressibility of the apparatus itself. This is done by placing the consolidometer with saturated porous stones and filter papers in the loading device and applying the load increments to be used in the compressibility test.
@etconp
Strain to strain unlike strength of material
Soil compressibility is the capability of a soil to decrease in volume when subjected to a mechanical load. The process that describes the decrease in soil volume (soil densification) under an externally applied load is called compression. ... Simply, consolidation refers to compression of saturated soil.
The practical significance of the soil‐compressibility determination lies in describing the ease with which the soils are susceptible to soil compaction. Laboratory tests for measuring soil compressibility are normally conducted either in a consolidometer or in a triaxial compression cell. This chapter focuses on one‐dimensional compression in a consolidometer. In the compressibility test using a consolidometer, only measurements of volume change of the soil specimens are desired; therefore, corrections must be applied for any significant deformation caused by the compressibility of the apparatus itself. This is done by placing the consolidometer with saturated porous stones and filter papers in the loading device and applying the load increments to be used in the compressibility test.
@etconp
Quiz for architecture students
In this collage (collection of pictures) 👆🏾👆🏾there are four types of architectural style . What type of architectural style is used in picture 3?
1. Modern architecture
2. Gothic architecture
3. Renaissance architecture
4. Medieval architecture
5. Islamic architecture
NB:- As you all know we have posted about las Lajas sanctuary ⛪️ on 12th of april 2020GC and in that picture we have mentioned the style of architecture.
https://t.me/ETCONP/2928
እንደምታውቁት በ April 12 - 2020 እአአ ስለ Las lajas ቤተመቅደስ ስነ ህንፃ ዘይቤ post አርገንላችው ነበር።
https://t.me/ETCONP/2928
If 100 people participate on this question we will share you three lecture notes regarding history of architecture
በዚህ ጥያቄ 100 ሰዎች ከተሳተፉ 3 lecture note ስለ history of architecture እንለቅላቸዋለን። ባታውቁትም ተሳተፉ
#share #participate
@etconp
In this collage (collection of pictures) 👆🏾👆🏾there are four types of architectural style . What type of architectural style is used in picture 3?
1. Modern architecture
2. Gothic architecture
3. Renaissance architecture
4. Medieval architecture
5. Islamic architecture
NB:- As you all know we have posted about las Lajas sanctuary ⛪️ on 12th of april 2020GC and in that picture we have mentioned the style of architecture.
https://t.me/ETCONP/2928
እንደምታውቁት በ April 12 - 2020 እአአ ስለ Las lajas ቤተመቅደስ ስነ ህንፃ ዘይቤ post አርገንላችው ነበር።
https://t.me/ETCONP/2928
If 100 people participate on this question we will share you three lecture notes regarding history of architecture
በዚህ ጥያቄ 100 ሰዎች ከተሳተፉ 3 lecture note ስለ history of architecture እንለቅላቸዋለን። ባታውቁትም ተሳተፉ
#share #participate
@etconp
Steel structure design quiz 🔔 🔔 🔔
Suppose 👆🏾👆🏾this is I section steel beam. what does number 1 , 2 and 3 represent ?
1️⃣ 1. flange 2. Web
3. Bottom flange
2️⃣ 1. Bottom flange 2. Web
3. Flange
3️⃣ 1. Top flange 2. Web
3. Bottom flange
4️⃣ All of the above
#steel #quiz #etconp #share
ይህን ጥያቄ ለጓደኞቻችው በማጋራት አጋርነታችሁን አሳዩን 🙏
@etconp
Suppose 👆🏾👆🏾this is I section steel beam. what does number 1 , 2 and 3 represent ?
1️⃣ 1. flange 2. Web
3. Bottom flange
2️⃣ 1. Bottom flange 2. Web
3. Flange
3️⃣ 1. Top flange 2. Web
3. Bottom flange
4️⃣ All of the above
#steel #quiz #etconp #share
ይህን ጥያቄ ለጓደኞቻችው በማጋራት አጋርነታችሁን አሳዩን 🙏
@etconp
Ethio Construction Engineering
What is the problem of the beam detailing? Your ideas @cotmp #detailing #drafting @etconp
The main problem of this beam detailing was the laping position of negative (top) and positive (bottom) bars. The negative bars must be lap far from support and the positive bars should be lap at support. Meaning negative moments maximum at support and positive moment maximum at span.
Additionally, the spacing of stirrups at critical region not correct.
@etconp
Additionally, the spacing of stirrups at critical region not correct.
@etconp
Ethio Construction Engineering via @like
Steel structure design quiz 🔔 🔔 🔔 Suppose 👆🏾👆🏾this is I section steel beam. what does number 1 , 2 and 3 represent ? 1️⃣ 1. flange 2. Web 3. Bottom flange 2️⃣ 1. Bottom flange 2. Web 3. Flange 3️⃣ 1. Top flange 2. Web 3.…
Answer for this question 👆🏾👆🏾is 3️⃣
1. Top flange 2. Web 3. Bottom flange
An I-beam, also known as H-beam (for universal column, UC), w-beam (for "wide flange"), universal beam (UB), rolled steel joist (RSJ), or double-T (especially in Polish 🇵🇱 , Bulgarian 🇧🇬 , Spanish 🇪🇸 , Italian 🇮🇹 and German 🇩🇪 ), is a beam with an I or H-shaped cross-section. The horizontal elements of the I are flanges, and the vertical element is the "web". I-beams are usually made of structural steel and are used in construction and civil engineering.
The web resists shear forces, while the flanges resist most of the bending moment experienced by the beam.
[Wikipedia]
@etconp
https://t.me/etconp
1. Top flange 2. Web 3. Bottom flange
An I-beam, also known as H-beam (for universal column, UC), w-beam (for "wide flange"), universal beam (UB), rolled steel joist (RSJ), or double-T (especially in Polish 🇵🇱 , Bulgarian 🇧🇬 , Spanish 🇪🇸 , Italian 🇮🇹 and German 🇩🇪 ), is a beam with an I or H-shaped cross-section. The horizontal elements of the I are flanges, and the vertical element is the "web". I-beams are usually made of structural steel and are used in construction and civil engineering.
The web resists shear forces, while the flanges resist most of the bending moment experienced by the beam.
[Wikipedia]
@etconp
https://t.me/etconp
Name this equipment ?
1. Tele-handler
2. Hoist
3. telescopic boom
4. Forklift
#equipment #share
@etconp
https://t.me/etconp
1. Tele-handler
2. Hoist
3. telescopic boom
4. Forklift
#equipment #share
@etconp
https://t.me/etconp
Forwarded from Ethio Construction Engineering (जॉर्डनो ג׳ורדנו ጆርዳኖ جوردانو จอร์แดโน่ JORDANO Ιορδάνοςஜார்டானோ)
Super Elevation
👉🏿 Objective
👉🏿 Concept
g(fs + e)
Where : e= rate of super elevation
fs = coefficient of friction
R = radius of horizontal curve in meter
V = design speed in m/s
g= 9.81 m/s
#highway #superelevation
❓ስለዚህ super elevation ምን ትላላችሁ?
❓What do you say about this super elevation?
@etconp
👉🏿 Objective
To counteract the centrifugal force acting on the vehicle at circular curves.👉🏿 Concept
Raise the road at the edge so the weight component vehicle balance the centrifugal acceleration and avoid the slipping and overturning or vehicle.
👉🏿 Equations
Rv = V²g(fs + e)
Where : e= rate of super elevation
fs = coefficient of friction
R = radius of horizontal curve in meter
V = design speed in m/s
g= 9.81 m/s
#highway #superelevation
❓ስለዚህ super elevation ምን ትላላችሁ?
❓What do you say about this super elevation?
@etconp