👉Design Of Columns As Per ACI
🚧1- Maximum and Minimum Reinforcement Ratio
▶️The minimum reinforcement ratio of 1 % is to be used in tied or spirally reinforced columns.
▶️This minimum reinforcement is needed to safeguard against any bending, reduce the effect of shrinkage and creep and enhance the ductility of columns.
🚧2- Minimum Number of Reinforcing Bars
▶️Minimum four bars within rectangular or circular sections; or one bar in each corner of the cross section for other shapes and a minimum of six bars in spirally reinforced columns should be used.
🚧3- Clear Distance between Reinforcing Bars
▶️For tied or spirally reinforced columns, clear distance between bars should not be less than the larger of 150 times bar diameter or 4 cm.
🚧4- Concrete Protection Cover
▶️The clear concrete cover should not be less than 4 cm for columns not exposed to weather or in contact with the ground.
▶️It is essential for protecting the reinforcement from corrosion or fire hazards.
🚧5- Minimum Cross Sectional Dimensions
▶️For practical considerations, column dimensions can be taken as multiples of 5 cm.
🚧6- Lateral Reinforcement
▶️Ties are effective in restraining the longitudinal bars from buckling out through the surface of the column, holding the reinforcement cage together during the construction process, confining the concrete core and when columns are subjected to horizontal forces, they serve as shear reinforcement.
▶️Spirals, on the other hand, serve in addition to these benefits in compensating for the strength loss due to spalling of the outside concrete shell at ultimate column strength.
🚧7- Ties
▶️For longitudinal bars, 32 mm or smaller, lateral ties 10 mm in diameter should be used.
▶️In some countries, ties of 8 mm dia are used for column construction.
#Structure
@etconp
🚧1- Maximum and Minimum Reinforcement Ratio
▶️The minimum reinforcement ratio of 1 % is to be used in tied or spirally reinforced columns.
▶️This minimum reinforcement is needed to safeguard against any bending, reduce the effect of shrinkage and creep and enhance the ductility of columns.
🚧2- Minimum Number of Reinforcing Bars
▶️Minimum four bars within rectangular or circular sections; or one bar in each corner of the cross section for other shapes and a minimum of six bars in spirally reinforced columns should be used.
🚧3- Clear Distance between Reinforcing Bars
▶️For tied or spirally reinforced columns, clear distance between bars should not be less than the larger of 150 times bar diameter or 4 cm.
🚧4- Concrete Protection Cover
▶️The clear concrete cover should not be less than 4 cm for columns not exposed to weather or in contact with the ground.
▶️It is essential for protecting the reinforcement from corrosion or fire hazards.
🚧5- Minimum Cross Sectional Dimensions
▶️For practical considerations, column dimensions can be taken as multiples of 5 cm.
🚧6- Lateral Reinforcement
▶️Ties are effective in restraining the longitudinal bars from buckling out through the surface of the column, holding the reinforcement cage together during the construction process, confining the concrete core and when columns are subjected to horizontal forces, they serve as shear reinforcement.
▶️Spirals, on the other hand, serve in addition to these benefits in compensating for the strength loss due to spalling of the outside concrete shell at ultimate column strength.
🚧7- Ties
▶️For longitudinal bars, 32 mm or smaller, lateral ties 10 mm in diameter should be used.
▶️In some countries, ties of 8 mm dia are used for column construction.
#Structure
@etconp
👉ስለ Contour Lines ኣብረን እንይ
🏷Characteristics of contour lines are:
*⃣1. Connect point of equal elevation.
*⃣2. Always connects close contour lines. This is not always visible on the map.
*⃣3. They never cross, split or intersect-at a cliff they might merge.
*⃣4. Evenly spaced contour lines indicate a uniform slope.
*⃣5. Closely spaced contour lines show a steep slope.
*⃣6. Widely spaced contour lines show gentle slope.
*⃣7. Uneven spacing- irregular or variable slope.
*⃣9. Closed contours with arrow in the centre represent depressions.
🏷Other characteristics of contour lines are
*⃣Horizontal distance between contour lines is inversely proportional to slope.
*⃣Uniform slopes have uniformly spaced lines.
*⃣Along plane surfaces, contour lines are straight and parallel.
*⃣Contour lines are perpendicular to lines of steepest slopes.
*⃣For summits or depressions, contour lines most close upon themselves.
*⃣A single contour line can not lie between two lines of higher or lower elevation.
🏷There are some basic rules for contour lines
⏺1. A contour line must never split or divide.
⏺2. A contour line must never simply end, except at the edge of the map.
⏺3. A contour line must represent one and only one elevation.
⏺4. A contour line may never intersect other contour lines
*⃣Overhanging cliffs are
the only exception.
⏺5. Concentric circles of contour lines indicate a hilltop or mountain peak.
⏺6. Concentric circles of hatched contour lines indicate a closed depression.
#Surveying
@etconp
🏷Characteristics of contour lines are:
*⃣1. Connect point of equal elevation.
*⃣2. Always connects close contour lines. This is not always visible on the map.
*⃣3. They never cross, split or intersect-at a cliff they might merge.
*⃣4. Evenly spaced contour lines indicate a uniform slope.
*⃣5. Closely spaced contour lines show a steep slope.
*⃣6. Widely spaced contour lines show gentle slope.
*⃣7. Uneven spacing- irregular or variable slope.
*⃣9. Closed contours with arrow in the centre represent depressions.
🏷Other characteristics of contour lines are
*⃣Horizontal distance between contour lines is inversely proportional to slope.
*⃣Uniform slopes have uniformly spaced lines.
*⃣Along plane surfaces, contour lines are straight and parallel.
*⃣Contour lines are perpendicular to lines of steepest slopes.
*⃣For summits or depressions, contour lines most close upon themselves.
*⃣A single contour line can not lie between two lines of higher or lower elevation.
🏷There are some basic rules for contour lines
⏺1. A contour line must never split or divide.
⏺2. A contour line must never simply end, except at the edge of the map.
⏺3. A contour line must represent one and only one elevation.
⏺4. A contour line may never intersect other contour lines
*⃣Overhanging cliffs are
the only exception.
⏺5. Concentric circles of contour lines indicate a hilltop or mountain peak.
⏺6. Concentric circles of hatched contour lines indicate a closed depression.
#Surveying
@etconp
👉አሳዛኝ ዜና
➡️በአዳማ ከተማ በህንፃ መደርመስ አደጋ የአራት ሰዎች ህይወት አለፈ
🚧በአዳማ ከተማ መስተዳድር ዳቤ ክፍለ ከተማ ኢሬቻ ቀበሌ ልዩ ቦታው ደጀኔ ስሜ ትምህርት ቤት አካባቢ በዛሬው እለት ከጠዋቱ 4 ሰዓት በግንባታ ላይ የነበረ ህንፃ የመደርመስ አደጋ አጋጥሟል።
🚧የቀድሞውን የሀዊ ሆቴል በማፍረስ በአዲስ የግንባታ ሂደት ላይ እያለ ባጋጠመ አደጋ በግንባታው ላይ የነበሩ አራት የቀን ሰራተኞች ህይወታቸው ማለፉን በአዳማ ከተማ ፖሊስ መምሪያ የህዝብ ግንኙነት ረዳት ኢንስፔክተር ወርቅነሽ ገልሜቻ ለብስራት ሬድዮ ተናግረዋል።
🚧በአደጋው ሌሎች ሁለት ሰዎች ባጋጠማቸው ጉዳት በአዳማ ሆስፒታል ህክምናቸውን እየተከታተሉ ይገኛል።
🚧በግንባታ ወቅት የጥንቃቄ ጉድለት እንደነበር ተስተውሏል።
Via ብስራት ሬድዮ
#FirstSafety
@etconp
➡️በአዳማ ከተማ በህንፃ መደርመስ አደጋ የአራት ሰዎች ህይወት አለፈ
🚧በአዳማ ከተማ መስተዳድር ዳቤ ክፍለ ከተማ ኢሬቻ ቀበሌ ልዩ ቦታው ደጀኔ ስሜ ትምህርት ቤት አካባቢ በዛሬው እለት ከጠዋቱ 4 ሰዓት በግንባታ ላይ የነበረ ህንፃ የመደርመስ አደጋ አጋጥሟል።
🚧የቀድሞውን የሀዊ ሆቴል በማፍረስ በአዲስ የግንባታ ሂደት ላይ እያለ ባጋጠመ አደጋ በግንባታው ላይ የነበሩ አራት የቀን ሰራተኞች ህይወታቸው ማለፉን በአዳማ ከተማ ፖሊስ መምሪያ የህዝብ ግንኙነት ረዳት ኢንስፔክተር ወርቅነሽ ገልሜቻ ለብስራት ሬድዮ ተናግረዋል።
🚧በአደጋው ሌሎች ሁለት ሰዎች ባጋጠማቸው ጉዳት በአዳማ ሆስፒታል ህክምናቸውን እየተከታተሉ ይገኛል።
🚧በግንባታ ወቅት የጥንቃቄ ጉድለት እንደነበር ተስተውሏል።
Via ብስራት ሬድዮ
#FirstSafety
@etconp
🔖በኮንስትራክሽን ኢንዱስትሪ ዘርፍ ላላቹ ባለሙያዎች በሙሉ
✉️የ ኮንስትራክሽን ስራዎች ተቆጣጣሪ ባለስልጣን እርስዎ ባሉበት ሁነው የ ኮንስትራክሽን ሞያ ፍቃድ የምትጠይቁበት ኤሌክትሮኒክ አገልግሎት (web based e-service system) ዘርግተዋል።
🚧ሂደቱ ከዚህ ፅሁፍ በምስል አስደግፈን አያይዘንላቹዋል።
@etconp
✉️የ ኮንስትራክሽን ስራዎች ተቆጣጣሪ ባለስልጣን እርስዎ ባሉበት ሁነው የ ኮንስትራክሽን ሞያ ፍቃድ የምትጠይቁበት ኤሌክትሮኒክ አገልግሎት (web based e-service system) ዘርግተዋል።
🚧ሂደቱ ከዚህ ፅሁፍ በምስል አስደግፈን አያይዘንላቹዋል።
@etconp
👉Low Cost Housing
➡️Low Cost Housing is a new concept which deals with effective budgeting and following of techniques which help in reducing the cost of construction through the use of locally available materials along with improved skills and technology without sacrificing the strength, performance and life of the structure.
▶️There is huge misconception that low cost housing is suitable for only sub standard works and they are constructed by utilizing cheap building materials of low quality.
▶️The fact is that Low cost housing is done by proper management of resources.
▶️Economy is also achieved by postponing finishing works or implementing them in phases.
🏷Building Cost
▶️The building construction cost can be divided into two parts namely Building
*⃣material cost : 65 to 70 %
*⃣Labour cost : 65 to 70 %
➡️Now in low cost housing, building material cost is less because we make use of the locally available materials and also the labour cost can be reduced by properly making the time schedule of our work.
➡️Cost of reduction is achieved by selection of more efficient material or by an improved design.
🏷Areas from where cost can be reduced are:-
🚧1) Reduce plinth area by using thinner wall concept.
*⃣Example 15 cm thick solid concrete block wall.
🚧2) Use locally available material in an innovative form like soil cement blocks in place of burnt brick.
🚧3) Use energy efficiency materials which consumes less energy like concrete block in place of burnt brick.
🚧4) Use environmentally friendly materials which are substitute for conventional building components like use R.C.C. Door and window frames in place of wooden frames.
🚧5) Preplan every component of a house and rationalize the design procedure for reducing the size of the component in the building.
🚧6) By planning each and every component of a house the wastage of materials due to demolition of the unplanned component of the house can be avoided.
🚧7) Each component of the house shall be checked whether if it’s necessary, if it is not necessary, then that component should not be used.
#ConstructionTechnology
@etconp
➡️Low Cost Housing is a new concept which deals with effective budgeting and following of techniques which help in reducing the cost of construction through the use of locally available materials along with improved skills and technology without sacrificing the strength, performance and life of the structure.
▶️There is huge misconception that low cost housing is suitable for only sub standard works and they are constructed by utilizing cheap building materials of low quality.
▶️The fact is that Low cost housing is done by proper management of resources.
▶️Economy is also achieved by postponing finishing works or implementing them in phases.
🏷Building Cost
▶️The building construction cost can be divided into two parts namely Building
*⃣material cost : 65 to 70 %
*⃣Labour cost : 65 to 70 %
➡️Now in low cost housing, building material cost is less because we make use of the locally available materials and also the labour cost can be reduced by properly making the time schedule of our work.
➡️Cost of reduction is achieved by selection of more efficient material or by an improved design.
🏷Areas from where cost can be reduced are:-
🚧1) Reduce plinth area by using thinner wall concept.
*⃣Example 15 cm thick solid concrete block wall.
🚧2) Use locally available material in an innovative form like soil cement blocks in place of burnt brick.
🚧3) Use energy efficiency materials which consumes less energy like concrete block in place of burnt brick.
🚧4) Use environmentally friendly materials which are substitute for conventional building components like use R.C.C. Door and window frames in place of wooden frames.
🚧5) Preplan every component of a house and rationalize the design procedure for reducing the size of the component in the building.
🚧6) By planning each and every component of a house the wastage of materials due to demolition of the unplanned component of the house can be avoided.
🚧7) Each component of the house shall be checked whether if it’s necessary, if it is not necessary, then that component should not be used.
#ConstructionTechnology
@etconp
👉Important concepts
🔹Which type of cement is used for underground concrete structures ?
➡️SRC (Sulphate Resisting Cement)
▶️The use of SRC is recommended for following applications:
*⃣Foundations, piles, basements and underground structures.
*⃣Sewage and Water treatment plants.
🔹What Is Roller Support
➡️Roller supports only resists perpendicular forces and they cannot resist parallel or horizontal forces & moment.
➡️It means the roller support will move freely along the surface without resisting horizontal force.
🔹What is the Concrete Temperature?
➡️Concrete temperature should not be more than 33°C & not less than 15°C in cold weather But the pumping temperature of concrete in hot weather should be 26°C.
🔹Do you know SPT ?
➡️SPT (Standard Penetration Test) is carried out to know the bearing capacity of soil.
➡️This is usually done on the foundation of bridges and the huge buildings.
#ConstructionNotes
@etconp
🔹Which type of cement is used for underground concrete structures ?
➡️SRC (Sulphate Resisting Cement)
▶️The use of SRC is recommended for following applications:
*⃣Foundations, piles, basements and underground structures.
*⃣Sewage and Water treatment plants.
🔹What Is Roller Support
➡️Roller supports only resists perpendicular forces and they cannot resist parallel or horizontal forces & moment.
➡️It means the roller support will move freely along the surface without resisting horizontal force.
🔹What is the Concrete Temperature?
➡️Concrete temperature should not be more than 33°C & not less than 15°C in cold weather But the pumping temperature of concrete in hot weather should be 26°C.
🔹Do you know SPT ?
➡️SPT (Standard Penetration Test) is carried out to know the bearing capacity of soil.
➡️This is usually done on the foundation of bridges and the huge buildings.
#ConstructionNotes
@etconp
👉Important Different Notes
🔹What is Fixed Supports
➡️Fixed supports are also known as rigid supports.
➡️Fixed supports are restrained against both rotation and translation so that they can resist any type of force or moment.
🔹Pinned / Hinged Support
➡️Pinned or hinged support can resist both vertical and horizontal forces but they cannot resist a moment.
➡️It means that hinged support is restrained against translation.
🔹What is Strip footing
➡️It is a component of shallow foundation which distributes the weight of a load bearing wall across the area of the ground.
➡️It is also known as a wall footing.
🔹What is Purpose of liquid limit test of soil
➡️Liquid limit can be determined to know shearing resistance of the soil.
🔹Difference between Earthen and Gravel Road
🚧Earthen Roads
➡️Earthen roads are lay with soil But, They are cheaper of all types of roads.
➡️Generally, This type of road is provided for less traffic areas and or for countryside areas.
➡️Good drainage system should be require which reflects good performance for longer period.
🚧Gravel Roads
➡️Gravel roads are also low quality roads but they are good when compare to earthen roads.
➡️Compacted mixture of gravel and earth is use as pavement material in this case.
#ConstructionNotes
@etconp
🔹What is Fixed Supports
➡️Fixed supports are also known as rigid supports.
➡️Fixed supports are restrained against both rotation and translation so that they can resist any type of force or moment.
🔹Pinned / Hinged Support
➡️Pinned or hinged support can resist both vertical and horizontal forces but they cannot resist a moment.
➡️It means that hinged support is restrained against translation.
🔹What is Strip footing
➡️It is a component of shallow foundation which distributes the weight of a load bearing wall across the area of the ground.
➡️It is also known as a wall footing.
🔹What is Purpose of liquid limit test of soil
➡️Liquid limit can be determined to know shearing resistance of the soil.
🔹Difference between Earthen and Gravel Road
🚧Earthen Roads
➡️Earthen roads are lay with soil But, They are cheaper of all types of roads.
➡️Generally, This type of road is provided for less traffic areas and or for countryside areas.
➡️Good drainage system should be require which reflects good performance for longer period.
🚧Gravel Roads
➡️Gravel roads are also low quality roads but they are good when compare to earthen roads.
➡️Compacted mixture of gravel and earth is use as pavement material in this case.
#ConstructionNotes
@etconp
@ETCONp_የከተማ_ልማት_እና_ኮንስትራክሽን_ሚኒስቴር_የ10_ዓመት_እቅድ_.Pdf
4.9 MB
👉ውድ የቻናላችን ቤተሰቦች
🚧የከተማ ልማት እና ኮንስትራክሽን ሚኒስቴር ለመጪዎቹ 10 ዓመታት ያስቀመጣቸው እቅዶች በ PDF ላኩልን ላላቹን ከዚህ ፅሁፍ አያይዘንላቹሃል።
@etconp
🚧የከተማ ልማት እና ኮንስትራክሽን ሚኒስቴር ለመጪዎቹ 10 ዓመታት ያስቀመጣቸው እቅዶች በ PDF ላኩልን ላላቹን ከዚህ ፅሁፍ አያይዘንላቹሃል።
@etconp
🔖ማስታወቂያ ለግንባታ ግብዓት አምራቾች❗️
👉የአዲስ አበባ ከተማ አስተዳደር ኮንስትራክሽን ቢሮ በአዋጅ ቁጥር 64/2011 ከተሰጡት ተግባርና ኃላፊነቶች መካከል የኮንስትራክሽን ማሽነሪ አከራዮች፣የግንባታ ግብዓት አምራቾችናአቅራቢዎች፣አማካሪዎች፣የስራ ተቋራጮችና ባለሞያዎችን በመመዝገብ የብቃት ማረጋገጫ የምስክር ወረቀት መስጠት ይገኝበታል፡፡
🚧ስለሆነም በየክፍለከተማው ተደራጅተውም ሆነ በግል የግንባታ ግብዓት የሚያመርቱ አምራቾች የሚያመርቱት የግንባታ ግብዓት ጥራቱን የጠበቀ መሆኑን ለማረጋገጥና ፍትሀዊ የሆነ ውድድር ለማስፈን እንዲቻል እስከ ጥቅምት 30/2013 ዓም ድረስ የአዲስ አበባ ከተማ አስተዳደር ኮንስትራክሽን ቢሮ 7ኛ ፎቅ በመምጣት የብቃት ማረጋገጫ የምስክር ወረቀት እንዲያወጡ እየጠየቅን ማንኛውም የግንባታ ግብዓት አምራች ከቢሮው የብቃት ማረጋገጫ የምስክር ወረቀት ሳይኖረው ማምረት የማይችል መሆኑን በዚሁ አጋጣሚ እናሳስባለን፡፡
✉️የአ/አ/ከ/አ/ኮንስትራክሽን ቢሮ
🏷ጥቅምት 11/2013 ዓ/ም
@etconp
👉የአዲስ አበባ ከተማ አስተዳደር ኮንስትራክሽን ቢሮ በአዋጅ ቁጥር 64/2011 ከተሰጡት ተግባርና ኃላፊነቶች መካከል የኮንስትራክሽን ማሽነሪ አከራዮች፣የግንባታ ግብዓት አምራቾችናአቅራቢዎች፣አማካሪዎች፣የስራ ተቋራጮችና ባለሞያዎችን በመመዝገብ የብቃት ማረጋገጫ የምስክር ወረቀት መስጠት ይገኝበታል፡፡
🚧ስለሆነም በየክፍለከተማው ተደራጅተውም ሆነ በግል የግንባታ ግብዓት የሚያመርቱ አምራቾች የሚያመርቱት የግንባታ ግብዓት ጥራቱን የጠበቀ መሆኑን ለማረጋገጥና ፍትሀዊ የሆነ ውድድር ለማስፈን እንዲቻል እስከ ጥቅምት 30/2013 ዓም ድረስ የአዲስ አበባ ከተማ አስተዳደር ኮንስትራክሽን ቢሮ 7ኛ ፎቅ በመምጣት የብቃት ማረጋገጫ የምስክር ወረቀት እንዲያወጡ እየጠየቅን ማንኛውም የግንባታ ግብዓት አምራች ከቢሮው የብቃት ማረጋገጫ የምስክር ወረቀት ሳይኖረው ማምረት የማይችል መሆኑን በዚሁ አጋጣሚ እናሳስባለን፡፡
✉️የአ/አ/ከ/አ/ኮንስትራክሽን ቢሮ
🏷ጥቅምት 11/2013 ዓ/ም
@etconp
👉አሳዛኝ ዜና
➡️በዲላ ከተማ የቤት ግድግዳ ተደርምሶ የ3 ሰዎች ህይወት አለፈ!
🚧በዲላ ከተማ የቤት ግድግዳ ተደርምሶ በደረሰ አደጋ ግድግዳው ስር ተኝተው የነበሩ ሶስት የጎዳና ተዳዳሪዎች ህይወት ማለፉን ፖሊስ አስታወቀ።
🚧የከተማው ፖሊስ ጽህፈት ቤት መርማሪ ፖሊስ ሣጅን ጌታሁን ኃይለማሪያም እንደገለጹት፤ አደጋው የደረሰው ትናንት በዲላ ወልዴና ቀበሌ በቀድሞ የዲላ ከተማ ማዘጋጃ ቤት ቢሮ የነበረው ግድግዳ በመደርመሱ ነው።
🚧ሁለት ሰዎች ደግሞ ከባድና ቀላል የአካል ጉዳት ደርሶባቸው በዲላ ዩኒቪርሲቲ ሪፌራል ሆስፒታል የህክምና እርዳታ እየተደረገላቸው መሆኑን አስረድተዋል።
🚧የአደጋው መንሰኤ ከዚህ ቀደም የከተማው ማዘጋጃ ቤት የነበረው ቢሮ ለእድሳት የቤቱ ክዳን ቆርቆሮ ተነስቶ ቤቱ ሙሉ በሙሉ ባለመፍረሱ ቆሞ የነበረ ግድግዳ በዕለቱ ከጣለው ዝናብ ጋር ተያይዞ በመደርመሱ መሆኑን ሣጅን ጌታሁን ተናግረዋል።
🚧በዚህም ተጠያቂ የሆኑ ሰዎች ተለይተው ምርመራ እየተደረገባቸው መሆኑን መርማሪው ገልጸዋል።
Via ENA
#FirstSafety
@etconp
➡️በዲላ ከተማ የቤት ግድግዳ ተደርምሶ የ3 ሰዎች ህይወት አለፈ!
🚧በዲላ ከተማ የቤት ግድግዳ ተደርምሶ በደረሰ አደጋ ግድግዳው ስር ተኝተው የነበሩ ሶስት የጎዳና ተዳዳሪዎች ህይወት ማለፉን ፖሊስ አስታወቀ።
🚧የከተማው ፖሊስ ጽህፈት ቤት መርማሪ ፖሊስ ሣጅን ጌታሁን ኃይለማሪያም እንደገለጹት፤ አደጋው የደረሰው ትናንት በዲላ ወልዴና ቀበሌ በቀድሞ የዲላ ከተማ ማዘጋጃ ቤት ቢሮ የነበረው ግድግዳ በመደርመሱ ነው።
🚧ሁለት ሰዎች ደግሞ ከባድና ቀላል የአካል ጉዳት ደርሶባቸው በዲላ ዩኒቪርሲቲ ሪፌራል ሆስፒታል የህክምና እርዳታ እየተደረገላቸው መሆኑን አስረድተዋል።
🚧የአደጋው መንሰኤ ከዚህ ቀደም የከተማው ማዘጋጃ ቤት የነበረው ቢሮ ለእድሳት የቤቱ ክዳን ቆርቆሮ ተነስቶ ቤቱ ሙሉ በሙሉ ባለመፍረሱ ቆሞ የነበረ ግድግዳ በዕለቱ ከጣለው ዝናብ ጋር ተያይዞ በመደርመሱ መሆኑን ሣጅን ጌታሁን ተናግረዋል።
🚧በዚህም ተጠያቂ የሆኑ ሰዎች ተለይተው ምርመራ እየተደረገባቸው መሆኑን መርማሪው ገልጸዋል።
Via ENA
#FirstSafety
@etconp
👉Important concepts
🔹Compression failure in columns
➡️When columns are axially loaded, the concrete and steel will experience some stresses.
➡️When the loads are greater in amount compared to the cross sectional area of the column, the concrete and steel will reach the yield stress and failure will be starting without any later deformation.
➡️In this type of failure, the material fails itself, not the whole column.
➡️This type of failure mostly occurs in shorter and wider columns.
➡️To avoid this, the column should be made with sufficient cross-sectional area compared to the allowable stress.
🚧Function of stirrups in the column
➡️Stirrups are provided to handle the shear force and to hold the rebars in position.
#ConstructionNotes
@etconp
🔹Compression failure in columns
➡️When columns are axially loaded, the concrete and steel will experience some stresses.
➡️When the loads are greater in amount compared to the cross sectional area of the column, the concrete and steel will reach the yield stress and failure will be starting without any later deformation.
➡️In this type of failure, the material fails itself, not the whole column.
➡️This type of failure mostly occurs in shorter and wider columns.
➡️To avoid this, the column should be made with sufficient cross-sectional area compared to the allowable stress.
🚧Function of stirrups in the column
➡️Stirrups are provided to handle the shear force and to hold the rebars in position.
#ConstructionNotes
@etconp
👉Important Notes
🔸Important concepts in Irrigation Engineering.
🚧Duty :
➡️The term duty means the area of land that can be irrigated with unit volume of irrigation water. Duty represents the irrigating capacity of a unit.
🚧Delta:
➡️It is the total depth of the water required by a crop during the entire period the crop is in the field and is denoted by the symbol ∆.
🏷What Is Barrage Mean
➡️A barrage is a type of low-head, diversion dam which consists of a number of large gates that can be opened or closed to control the amount of water passing through.
➡️This allows the structure to regulate and stabilize river water elevation upstream for use in irrigation and other systems.
🔹Purpose of Barrage
*⃣1. To maintain pond level.
*⃣2. To raise the water level during low supplies. In case of higher floods, shutters are dropped down and overflow takes place while in case of gated weir, gates are raised during floods.
🏷What Are The Various Tests on Concrete with Apparatus
⏺1. Slump Cone Test
⏺2. Compressive Strength Test
⏺3. Water Absorption Test
⏺4. Water Permeability Test
⏺5. Compaction Factor Test
🏷What Is Contour map Mean
➡️A topographic map on which the shape of the land surface is shown by contour lines, the relative spacing of the lines indicating the relative slope of the surface.
🏷What Is Development length
➡️Development length is an extera length of steel, which transfer the load from one steel bar to other.
#ConstructionNotes
@etconp
🔸Important concepts in Irrigation Engineering.
🚧Duty :
➡️The term duty means the area of land that can be irrigated with unit volume of irrigation water. Duty represents the irrigating capacity of a unit.
🚧Delta:
➡️It is the total depth of the water required by a crop during the entire period the crop is in the field and is denoted by the symbol ∆.
🏷What Is Barrage Mean
➡️A barrage is a type of low-head, diversion dam which consists of a number of large gates that can be opened or closed to control the amount of water passing through.
➡️This allows the structure to regulate and stabilize river water elevation upstream for use in irrigation and other systems.
🔹Purpose of Barrage
*⃣1. To maintain pond level.
*⃣2. To raise the water level during low supplies. In case of higher floods, shutters are dropped down and overflow takes place while in case of gated weir, gates are raised during floods.
🏷What Are The Various Tests on Concrete with Apparatus
⏺1. Slump Cone Test
⏺2. Compressive Strength Test
⏺3. Water Absorption Test
⏺4. Water Permeability Test
⏺5. Compaction Factor Test
🏷What Is Contour map Mean
➡️A topographic map on which the shape of the land surface is shown by contour lines, the relative spacing of the lines indicating the relative slope of the surface.
🏷What Is Development length
➡️Development length is an extera length of steel, which transfer the load from one steel bar to other.
#ConstructionNotes
@etconp
✋ሰላም ውድ የቻናላችን ቤተሰቦች ዛሬ እስቲ ይቺ ከታች ያለችው ጥያቄ እንወያይባት
👉በ Lump Sum ወይም በ DB ኮንትራት ውል (ስራ) ባለቤት ከተቋራጩ ጋር ለመስራት ከተዋዋለው የስራ አይነት መጠን በግንባታ ወቅት ቢጨምር ወይም ቢቀንስ ፣ በባለቤት ፍላጎት ወይም ከፍላጎት ውጭ ተጨማሪ ስራዎች ቢያጋጥመን መጀመሪያ የተገባበት የውለታ ገንዘብ መጠን በስራው ልክ አብሮ ሊጨምር ወይም ሊቀንስ ይችላል??
➡️ለግንባታው አስፈላጊ የሆነ ስራ በዲዛይን ውስጥ ሳይካተት ቢቀር በግንባታ ወቅት ባለቤቲ (Owner) ስራው መካተት አለበት ቢልስ ክፍያዎች እንዴት ይስተናገዳሉ?
#ConstructionLaw
📩ሀሳብ አስተያየትዎ ከታች ባለው ሊንክ ፃፉልን እና እንወያይበት
.
http://t.me/COTMp
👉በ Lump Sum ወይም በ DB ኮንትራት ውል (ስራ) ባለቤት ከተቋራጩ ጋር ለመስራት ከተዋዋለው የስራ አይነት መጠን በግንባታ ወቅት ቢጨምር ወይም ቢቀንስ ፣ በባለቤት ፍላጎት ወይም ከፍላጎት ውጭ ተጨማሪ ስራዎች ቢያጋጥመን መጀመሪያ የተገባበት የውለታ ገንዘብ መጠን በስራው ልክ አብሮ ሊጨምር ወይም ሊቀንስ ይችላል??
➡️ለግንባታው አስፈላጊ የሆነ ስራ በዲዛይን ውስጥ ሳይካተት ቢቀር በግንባታ ወቅት ባለቤቲ (Owner) ስራው መካተት አለበት ቢልስ ክፍያዎች እንዴት ይስተናገዳሉ?
#ConstructionLaw
📩ሀሳብ አስተያየትዎ ከታች ባለው ሊንክ ፃፉልን እና እንወያይበት
.
http://t.me/COTMp
Telegram
ETCONp Discussion
📩ለማነኛውም ሀሳብ እና አስተያየት @Philemona7
✌️ይህ የ @etconp መወያያ ግሩፓቹ ነው።
✋This is discussion group of @ETCONpWORK
.
🔖ማሳሰብያ ...
.
⚡️ግሩፑ ላይ ማነኛውም ከ ኮንስትራክሽን ጉዳዮች ውጪ መለጠፍ በፍፁም አይፈቀድም!
@ETCONpBOT ፃፉልን እናመሰግናለን🙏
✌️ይህ የ @etconp መወያያ ግሩፓቹ ነው።
✋This is discussion group of @ETCONpWORK
.
🔖ማሳሰብያ ...
.
⚡️ግሩፑ ላይ ማነኛውም ከ ኮንስትራክሽን ጉዳዮች ውጪ መለጠፍ በፍፁም አይፈቀድም!
@ETCONpBOT ፃፉልን እናመሰግናለን🙏
👉የኮይሻ ኃይል ማመንጫ ፕሮጀክትን በሦስት ዓመት ለማጠናቀቅ ጥረት እየተደረገ ነው!
➡️በኢትዮጵያ ከሕዳሴ ግድብ ቀጥሎ ሁለተኛው ግዙፍ ፕሮጀክት የሆነውና 2 ሺህ 160 ሜጋ ዋት ኃይል የማመንጨት አቅም ያለው የኮይሻ ኃይል ማመንጫ ግድብ አፈፃፀም 39 በመቶ መድረሱ ተገልጿል።
🚧የውሃ፣ መስኖና ኢነርጂ ሚኒስትሩ ስለሺ በቀለ(ዶ/ር፣ኢ/ር ) የኮይሻ ኃይል ማመንጫ ፕሮጀክትን በሶስት ዓመት ለማጠናቀቅ እየተሰራ መሆኑን ተናግረዋል።
🚧ግድቡ በቅርብ ርቀት ላይ የሚገኘውን የጊቤ ሶስት ውሃ የሚጠቀም በመሆኑ 6 ቢሊዮን ኪዩቢክ ሊትር ውሃ ብቻ እንዲይዝ ተደርጎ እንደሚገነባም ሚኒስትሩ ተናግረዋል፤ ይህም ግድቡን በፍጥነት ለማጠናቀቅ ዕድል ይሰጣል ብለዋል።
🚧የፕሮጀክቱ የኮንትራት ስራዎች ተቆጣጣሪ አቶ ኢዩኤል ሰለሞንም በእስካሁን ሂደት የውሃውን ተፈጥሯዊ አቅጣጫ ማስቀየርን ጨምሮ መሰረታዊ የቁፋሮ ስራዎች እና የማስተንፈሻ ግንባታ ቁፋሮው ከግማሽ በላይ መጠናቀቁንም ገልጸዋል።
🚧ግድቡ “በገበታ ለሀገር” የኮይሻ ፕሮጀክት መካተቱን ጠቅሰው፤ የግድቡ በፍጥነት መጠናቀቅ አካባቢውን የቱሪስት መዳረሻ በማድረግ ረገድ ሚናው የጎላ መሆኑን ተናግረዋል።
🚧ለአራት ሺህ ዜጎች የስራ ዕድል የፈጠረው የኮይሻ ኃይል ማመንጫ የግንባታ ስምምነቱ የተፈረመው በመጋቢት 2008 ዓ.ም ነው።
Via EBC
@etconp
➡️በኢትዮጵያ ከሕዳሴ ግድብ ቀጥሎ ሁለተኛው ግዙፍ ፕሮጀክት የሆነውና 2 ሺህ 160 ሜጋ ዋት ኃይል የማመንጨት አቅም ያለው የኮይሻ ኃይል ማመንጫ ግድብ አፈፃፀም 39 በመቶ መድረሱ ተገልጿል።
🚧የውሃ፣ መስኖና ኢነርጂ ሚኒስትሩ ስለሺ በቀለ(ዶ/ር፣ኢ/ር ) የኮይሻ ኃይል ማመንጫ ፕሮጀክትን በሶስት ዓመት ለማጠናቀቅ እየተሰራ መሆኑን ተናግረዋል።
🚧ግድቡ በቅርብ ርቀት ላይ የሚገኘውን የጊቤ ሶስት ውሃ የሚጠቀም በመሆኑ 6 ቢሊዮን ኪዩቢክ ሊትር ውሃ ብቻ እንዲይዝ ተደርጎ እንደሚገነባም ሚኒስትሩ ተናግረዋል፤ ይህም ግድቡን በፍጥነት ለማጠናቀቅ ዕድል ይሰጣል ብለዋል።
🚧የፕሮጀክቱ የኮንትራት ስራዎች ተቆጣጣሪ አቶ ኢዩኤል ሰለሞንም በእስካሁን ሂደት የውሃውን ተፈጥሯዊ አቅጣጫ ማስቀየርን ጨምሮ መሰረታዊ የቁፋሮ ስራዎች እና የማስተንፈሻ ግንባታ ቁፋሮው ከግማሽ በላይ መጠናቀቁንም ገልጸዋል።
🚧ግድቡ “በገበታ ለሀገር” የኮይሻ ፕሮጀክት መካተቱን ጠቅሰው፤ የግድቡ በፍጥነት መጠናቀቅ አካባቢውን የቱሪስት መዳረሻ በማድረግ ረገድ ሚናው የጎላ መሆኑን ተናግረዋል።
🚧ለአራት ሺህ ዜጎች የስራ ዕድል የፈጠረው የኮይሻ ኃይል ማመንጫ የግንባታ ስምምነቱ የተፈረመው በመጋቢት 2008 ዓ.ም ነው።
Via EBC
@etconp
👉Lets See About Structure Supports
🔹Fixed Supports
▶️Fixed supports are also known as rigid supports.
▶️Fixed supports are restrained against both rotation and translation so that they can resist any type of force or moment.
🔹Pinned / Hinged Support
▶️Pinned or hinged support can resist both vertical and horizontal forces but they cannot resist a moment.
▶️It means that hinged support is restrained against translation.
🔹Roller Support
▶️Roller supports only resists perpendicular forces and they cannot resist parallel or horizontal forces & moment.
▶️It means the roller support will move freely along the surface without resisting horizontal force.
#Structure
#ConstructionNotes
@etconp
🔹Fixed Supports
▶️Fixed supports are also known as rigid supports.
▶️Fixed supports are restrained against both rotation and translation so that they can resist any type of force or moment.
🔹Pinned / Hinged Support
▶️Pinned or hinged support can resist both vertical and horizontal forces but they cannot resist a moment.
▶️It means that hinged support is restrained against translation.
🔹Roller Support
▶️Roller supports only resists perpendicular forces and they cannot resist parallel or horizontal forces & moment.
▶️It means the roller support will move freely along the surface without resisting horizontal force.
#Structure
#ConstructionNotes
@etconp
📌Difference between working stress approach and limit state approach
🔸Working Stress Approach
➡️The service loads are used in the whole design and the strength of material is not utilized in the full extent.
➡️In this method of design, stresses acting on structural members are calculated based on elastic method and they are designed not to exceed certain allowable values.
➡️In fact, the whole structure during the life span may only experience loading stresses far below the ultimate state and that is the reason why this method is called working stress approach.
➡️Under such scenario, the most economical design can hardly be obtained by using working stress approach which is now commonly used in the design of temporary works.
🔸Limit State Approach
▶️For each material and load, a partial safety factor is assigned individually depending on the material properties and load properties.
▶️Therefore, each element of load and material properties is accurately assessed resulting in a more refined and accurate analysis of the structure.
▶️In this connection, the material strength can be utilized to its maximum value during its life span and loads can be assessed with reasonable probability of occurrence.
▶️Limit state approach is commonly used for the majority of reinforced concrete design because it ensures the utilization of material strength with the lowest construction cost input.
#ConstructionNotes
#Structure
@etconp
🔸Working Stress Approach
➡️The service loads are used in the whole design and the strength of material is not utilized in the full extent.
➡️In this method of design, stresses acting on structural members are calculated based on elastic method and they are designed not to exceed certain allowable values.
➡️In fact, the whole structure during the life span may only experience loading stresses far below the ultimate state and that is the reason why this method is called working stress approach.
➡️Under such scenario, the most economical design can hardly be obtained by using working stress approach which is now commonly used in the design of temporary works.
🔸Limit State Approach
▶️For each material and load, a partial safety factor is assigned individually depending on the material properties and load properties.
▶️Therefore, each element of load and material properties is accurately assessed resulting in a more refined and accurate analysis of the structure.
▶️In this connection, the material strength can be utilized to its maximum value during its life span and loads can be assessed with reasonable probability of occurrence.
▶️Limit state approach is commonly used for the majority of reinforced concrete design because it ensures the utilization of material strength with the lowest construction cost input.
#ConstructionNotes
#Structure
@etconp
📌Sound proofing
🔸Sound Proof Construction Techniques
➡️Unwelcome sound transmission in a building is typically perceived as a noise problem by the occupants.
➡️With more and more people living closer together, soundproof construction techniques are increasingly utilized in reducing noise and providing quieter working and living environments.
🔸The Fundamentals of Noise
➡️As human population density continually increases, the desire for peaceful, noise free living and working environments increases commensurately.
➡️Noise in this instance is defined as a collection of one or more unwelcome sounds as perceived by the hearer.
➡️Humans generally have little capacity for blocking their sense of hearing, unlike vision which can be “turned off’ simply by closing eyelids So any unwelcome sound that reaches the ear is usually considered undesirable and given the label of “noise".
➡️Even the pure tones of a musical scale can be perceived as noise if heard by unappreciative ears, and drives the quest for knowledge on how to sound proof a room for example.
➡️Reducing noise, then, is an exercise in eliminating sound transmission through walls, floors, and ceilings and is the goal of sound proof construction and design.
🔸Sound Proof Design Principles
➡️There are three broad design categories for sound transmission control
🚧Increase sealed dead space:
▶️As sound travels, acoustic energy is dissipated and the intensity or “volume" decreases as the result.
▶️This is why we usually cannot hear someone speaking who is standing far away.
▶️However, over short distances it is also important to eliminate sound transmission through the air which can be achieved by eliminating open penetrations through walls, floors, and ceilings.
▶️This is especially effective to soundproof existing rooms.
🚧Increase mass
▶️Sound is generated by vibrating objects generating pressure waves in the air.
▶️Sound can also cause objects to vibrate and regenerate these pressure waves at a different location on the object, but will lose acoustic energy in the process.
▶️The more massive an object is, the more energy is required to vibrate, and less energy is available to regenerate a sound.
🚧Decrease vibratory response
▶️Objects that do not readily vibrate in response to audible sound will not Transmit that sound.
▶️This is why a pillow will muffle, or dampen, sounds instead of regenerating them.
▶️Some soundproof window treatments rely on this method.
🚧Applying Sound Proof Design to Construction Practice
▶️There are several ways to sound proof a structure.
▶️The question of how to soundproof a room can be addressed with some surprisingly simple construction techniques, starting with building a sound proof wall for example Commonly used dry wall, or sheet rock, is actually an effective material for sound proofing due to its high mass.
▶️However, for maximum effect changes to the mounting system should be employed.
▶️A dampening material, such as a bead of silicone caulk, should be used between the sheet rock panel and framing.
▶️If allowed by code, cutting the sill plate to create an air gap in the middle of the sill effectively stops it from transmitting sound.
▶️Alternating studs on either side of the split sill plate stops sound transmission through the studs from one side of the wall to the other.
▶️Otherwise, an additional layer of sheetrock spaced with acoustic caulk or foam will also create an acoustically dead air gap. Acoustic drywall, which incorporates a dampening material layer in the sheet rock itself, can also be used.
▶️Other high mass building materials, such as concrete, stucco, logs, mass loaded vinyl, etc. can also be utilized in cost effective sound proof methods especially on exterior walls.
▶️Commonly overlooked sources of sound transmitters in a building are windows, pipes, electrical conduits, and wall penetrations for utilities.
#ConstructionTechnology
@etconp
🔸Sound Proof Construction Techniques
➡️Unwelcome sound transmission in a building is typically perceived as a noise problem by the occupants.
➡️With more and more people living closer together, soundproof construction techniques are increasingly utilized in reducing noise and providing quieter working and living environments.
🔸The Fundamentals of Noise
➡️As human population density continually increases, the desire for peaceful, noise free living and working environments increases commensurately.
➡️Noise in this instance is defined as a collection of one or more unwelcome sounds as perceived by the hearer.
➡️Humans generally have little capacity for blocking their sense of hearing, unlike vision which can be “turned off’ simply by closing eyelids So any unwelcome sound that reaches the ear is usually considered undesirable and given the label of “noise".
➡️Even the pure tones of a musical scale can be perceived as noise if heard by unappreciative ears, and drives the quest for knowledge on how to sound proof a room for example.
➡️Reducing noise, then, is an exercise in eliminating sound transmission through walls, floors, and ceilings and is the goal of sound proof construction and design.
🔸Sound Proof Design Principles
➡️There are three broad design categories for sound transmission control
🚧Increase sealed dead space:
▶️As sound travels, acoustic energy is dissipated and the intensity or “volume" decreases as the result.
▶️This is why we usually cannot hear someone speaking who is standing far away.
▶️However, over short distances it is also important to eliminate sound transmission through the air which can be achieved by eliminating open penetrations through walls, floors, and ceilings.
▶️This is especially effective to soundproof existing rooms.
🚧Increase mass
▶️Sound is generated by vibrating objects generating pressure waves in the air.
▶️Sound can also cause objects to vibrate and regenerate these pressure waves at a different location on the object, but will lose acoustic energy in the process.
▶️The more massive an object is, the more energy is required to vibrate, and less energy is available to regenerate a sound.
🚧Decrease vibratory response
▶️Objects that do not readily vibrate in response to audible sound will not Transmit that sound.
▶️This is why a pillow will muffle, or dampen, sounds instead of regenerating them.
▶️Some soundproof window treatments rely on this method.
🚧Applying Sound Proof Design to Construction Practice
▶️There are several ways to sound proof a structure.
▶️The question of how to soundproof a room can be addressed with some surprisingly simple construction techniques, starting with building a sound proof wall for example Commonly used dry wall, or sheet rock, is actually an effective material for sound proofing due to its high mass.
▶️However, for maximum effect changes to the mounting system should be employed.
▶️A dampening material, such as a bead of silicone caulk, should be used between the sheet rock panel and framing.
▶️If allowed by code, cutting the sill plate to create an air gap in the middle of the sill effectively stops it from transmitting sound.
▶️Alternating studs on either side of the split sill plate stops sound transmission through the studs from one side of the wall to the other.
▶️Otherwise, an additional layer of sheetrock spaced with acoustic caulk or foam will also create an acoustically dead air gap. Acoustic drywall, which incorporates a dampening material layer in the sheet rock itself, can also be used.
▶️Other high mass building materials, such as concrete, stucco, logs, mass loaded vinyl, etc. can also be utilized in cost effective sound proof methods especially on exterior walls.
▶️Commonly overlooked sources of sound transmitters in a building are windows, pipes, electrical conduits, and wall penetrations for utilities.
#ConstructionTechnology
@etconp
❤1👍1
When and why strengthening of reinforced concrete structures
The purpose of reinforcing concrete structures with a concrete or steel jacket increases the compressive and shear strength and maintains enclosure to enhance the ductility or bonding of concrete and reinforcement.
Strengthening systems are often classified into two categories: Passive systems and active systems.
Passive strengthening systems don't introduce forces to the structure or its elements. Passive systems like steel ferroconcrete enlargement and therefore the addition of steel components contribute to load sharing and therefore the overall resistance of the member once it deforms beneath external hundreds.
Active strengthening systems, like external post-tensioning (PT), involve the introduction of external forces to the structural parts that might offset half or all of the results of external masses.
For example, new post-tensioned mono-strands will be profiled on the span of an existing beam to supply uplift at mid-span which will be used to offset existing strength deficiency or permit the member to support extra load.
The primary reasons for the strengthening of concrete structures are typically to increase existing elements’ capacity to carry new loads or to resolve an existing deficiency. Several strengthening techniques such as section enlargement, externally bonded fiber reinforced polymer (FRP) reinforcement, supplemental steel elements...
Many Reasons to strengthening of Reinforce Concrete Structures:
1- When a structure is damaged by events such as earthquakes.
2- When the user of a residential building is changed.
3- When there are plans to increase the structural classes.
It is possible to maintain the shear strength, compression and enclosure of columns, walls, slabs and beams also their bearing capacity will increase against earthquake and vertical side loads.
#Structures
@etconp
The purpose of reinforcing concrete structures with a concrete or steel jacket increases the compressive and shear strength and maintains enclosure to enhance the ductility or bonding of concrete and reinforcement.
Strengthening systems are often classified into two categories: Passive systems and active systems.
Passive strengthening systems don't introduce forces to the structure or its elements. Passive systems like steel ferroconcrete enlargement and therefore the addition of steel components contribute to load sharing and therefore the overall resistance of the member once it deforms beneath external hundreds.
Active strengthening systems, like external post-tensioning (PT), involve the introduction of external forces to the structural parts that might offset half or all of the results of external masses.
For example, new post-tensioned mono-strands will be profiled on the span of an existing beam to supply uplift at mid-span which will be used to offset existing strength deficiency or permit the member to support extra load.
The primary reasons for the strengthening of concrete structures are typically to increase existing elements’ capacity to carry new loads or to resolve an existing deficiency. Several strengthening techniques such as section enlargement, externally bonded fiber reinforced polymer (FRP) reinforcement, supplemental steel elements...
Many Reasons to strengthening of Reinforce Concrete Structures:
1- When a structure is damaged by events such as earthquakes.
2- When the user of a residential building is changed.
3- When there are plans to increase the structural classes.
It is possible to maintain the shear strength, compression and enclosure of columns, walls, slabs and beams also their bearing capacity will increase against earthquake and vertical side loads.
#Structures
@etconp