Forwarded from 杨柳青
This media is not supported in your browser
VIEW IN TELEGRAM
This media is not supported in your browser
VIEW IN TELEGRAM
This media is not supported in your browser
VIEW IN TELEGRAM
This media is not supported in your browser
VIEW IN TELEGRAM
This media is not supported in your browser
VIEW IN TELEGRAM
This media is not supported in your browser
VIEW IN TELEGRAM
This media is not supported in your browser
VIEW IN TELEGRAM
This media is not supported in your browser
VIEW IN TELEGRAM
This media is not supported in your browser
VIEW IN TELEGRAM
This media is not supported in your browser
VIEW IN TELEGRAM
What is the name of these test performed on a ground surface?
Anonymous Quiz
25%
Cone penetration test
14%
Standard penetration test
52%
Field density test
9%
Plate load tesr
It is called field density test(FDT) using sand replacement method.
There are different methods used to determine the density of a compacted soil. Sand replacement method is one of them.
FDT test is probably the most frequently applied field test in a construction site. Before placing any RC structures( foundation,grade beam, grade slab..) into the ground surface, FDT should be performed and should pass the test.
FDT Is performed to determine the degree of compaction of a ground surface. Degree of compaction is given in a percentile value. As per AASHTO standard, insitu degree of compaction should be more than 95%. This means the on-site soil density must be atleast 95% of the maximum achievable compaction.
This is done first by determining the maximum dry density(MDD) and optimum moisture content(OMC) of the compacted fill material in the laboratory.
Next task is to compare the MDD value with that of the insitu dry density value.
The basic principle of sand replacement method is to measure the insitu volume of hole from which the material was excavated from the weight of sand with known density filling the hole. The insitu density of material is given by the weight of excavated material divided by insitu volume.
The sand replacement method can be a little bit tricky. It will better to check the procedure on a YouTube tutorial.
Note regarding FDT
-Considering a compaction thickness of 25cm,one FDT in every 200m3 should be taken.
- if the FDT failed,then the entire fill material is removed, replaced by another material and again compacted well.
-performing FDT prior to construction Is important in checking the stability of ground surface.
Part of report below from our project shows FDT test result and the obtained degree of compaction.👷♂️✌
@etconp
There are different methods used to determine the density of a compacted soil. Sand replacement method is one of them.
FDT test is probably the most frequently applied field test in a construction site. Before placing any RC structures( foundation,grade beam, grade slab..) into the ground surface, FDT should be performed and should pass the test.
FDT Is performed to determine the degree of compaction of a ground surface. Degree of compaction is given in a percentile value. As per AASHTO standard, insitu degree of compaction should be more than 95%. This means the on-site soil density must be atleast 95% of the maximum achievable compaction.
This is done first by determining the maximum dry density(MDD) and optimum moisture content(OMC) of the compacted fill material in the laboratory.
Next task is to compare the MDD value with that of the insitu dry density value.
The basic principle of sand replacement method is to measure the insitu volume of hole from which the material was excavated from the weight of sand with known density filling the hole. The insitu density of material is given by the weight of excavated material divided by insitu volume.
The sand replacement method can be a little bit tricky. It will better to check the procedure on a YouTube tutorial.
Note regarding FDT
-Considering a compaction thickness of 25cm,one FDT in every 200m3 should be taken.
- if the FDT failed,then the entire fill material is removed, replaced by another material and again compacted well.
-performing FDT prior to construction Is important in checking the stability of ground surface.
Part of report below from our project shows FDT test result and the obtained degree of compaction.👷♂️✌
@etconp
👍1
Forwarded from Samuel H
👍1
This media is not supported in your browser
VIEW IN TELEGRAM
How to build concrete masonry unit (CMU)
Facebook:- https://www.facebook.com/115479406977628/posts/120058029853099/?d=n
@etconp
Facebook:- https://www.facebook.com/115479406977628/posts/120058029853099/?d=n
@etconp
What is the name of this construction machinery?
Anonymous Quiz
37%
Backhoe loader
23%
Shovel loader
10%
Skid loader
30%
Boom loader
It is called a boom loader or tele handler or telescopic handler.
Knowing the different names and purposes of construction machineries is important.There are lots of loader family used on a construction sites. Boom loader is one of them.
Boom/teleescopic loader as its name implies, it has a boom that extends forward and upward like a telescope. It can be fitted with a forklift or a bucket. It is used to remove cargo from trailer, place materials to a roof top or higher places, transport materials within the site from one place to another.
Since a boom loader has a bucket and the boom can extend upto 17m, it is preferable on site to transfer material from the ground to a higher floor level.
@etconp
Knowing the different names and purposes of construction machineries is important.There are lots of loader family used on a construction sites. Boom loader is one of them.
Boom/teleescopic loader as its name implies, it has a boom that extends forward and upward like a telescope. It can be fitted with a forklift or a bucket. It is used to remove cargo from trailer, place materials to a roof top or higher places, transport materials within the site from one place to another.
Since a boom loader has a bucket and the boom can extend upto 17m, it is preferable on site to transfer material from the ground to a higher floor level.
@etconp
Forwarded from Ethio Construction Engineering
Media is too big
VIEW IN TELEGRAM
Forwarded from Ethio Construction Engineering
Principles_of_Foundation_Engineering.pdf
15.2 MB
📚 Book 👉 Principles of Foundation Engineering (7th Edition, SI Units)
👤 Author 👉 Braja M. Das @COTMp
👤 Author 👉 Braja M. Das @COTMp
Foundation_Engineering_Handbook.pdf
30 MB
📚 Book TIP @COTMp
👍3