Ethio Construction Engineering
32.3K subscribers
6.27K photos
359 videos
1.99K files
3.33K links
🔨 World Construction Engineering
Latest updates, tips, and tutorials on building, civil engineering, and construction in World.
Learn, build, and grow with us!

📨 @Philemona7 Or @ETCONpBOT

For Ad:- https://telega.io/c/etconp
Download Telegram
ዛሬ ማለዳ በቀን 67 ሺህ ሜትር ኪዩብ ውሃ መስጠት የሚችሉ፣ ከግማሽ ሚሊዮን በላይ የአዲስአበባ ነዋሪዎችን ተጠቃሚ የሚያደርጉ 1.8 ቢሊዮን ብር ወጪ የተደረገባቸው የንጹህ መጠጥ ውሀ፣ የፍሳሽ ማጣሪያ እና የውሀ ላብራቶሪ ፕሮጀክቶችን ተመርቀው ተከፍተዋል።

በቀን 67 ሺህ ሜትር ኪዩብ ውሃ መስጠት የሚችሉ 25 የውሀ ጉድጓዶች ቁፋሮ እና የውሀ መሰረተ ልማት ግንባታን በማጠናቀቅ አስፈላጊ የሆኑ ቁሳቁሶች አሟልተን ስራ ያስጀመርናቸው ፕሮጀክቶች የከተማዋን ዕለታዊ ውሃ የማምረት አቅም ወደ 792 ሺህ ሜትር ኪዩብ ከፍ የሚያደርጉ ይሆናል፡፡

ለሕብረተሰቡ የሚሰራጨውን ውሀ ደህንነት የሚያረጋግጥ ዓለም አቀፍ ደረጃ ያለው ዘመናዊ የውሃ እና ፍሳሽ ላብራቶሪ ተቋቁሞ አስፈላጊ የሆኑ ግብዓቶችን አሟልተን ስራ ያስጀመርናቸው ሲሆን፣ በሌላ በኩል የፍሳሽ ማጣሪያ እና 40 ኪሎ ሜትር የተለያዩ መጠን ያላቸው የውሀ ማስተላለፊያ መስመሮች ዝርጋታ ስራ እንዲጀምር አድርገናል፡፡

ሐምሌ 28 ቀን 2015 ዓም

Via Mayor Office

@etconp
👍6
👉DEEP BEAMS

🌟Deep beams are Reinforced concrete structural elements with large depths in relation to their spans.

⏺A deep beam is a beam in which a significant amount of the load is carried to the supports by a compression thrust joining the load and the reactions. According to the EBCS 2 1995, beams are considered as deep beams when l/h≤...2 for simple span and 2.5 for continuous

▶️Where l is the effective span measured center to center of supports or 1.15 times clear span, whichever is smaller and h is the overall depth of the deep beam.

⏺Deep beams are usually found at at transfer girders (girders support one or more columns transferring it laterally to other columns) used in multistory buildings to provide column offset , in foundation wall, pile cap rectangular suspended containers (tanks), raft slabs, pile caps, floor diaphragms, shear walls etc.
Behavior of Deep Beams
The behavior of deep beams is significantly different from that of beams of normal proportion (shallow beams) that it requires special consideration in analysis, design and detailing of reinforcement.

⏺Elastic analysis of such beams indicates that the usual hypothesis plane section before bending remains plane after bending is not valid for such members Thus flexural stresses are not linearly distributed even in the elastic range and hence the usual methods used for analysis and design of ordinary reinforced concrete beams are neither suitable nor adequate to determine the strength of reinforced concrete deep beams.

▶️The followings are the major different of deep beam element compared with ordinary beam

⏺Two-Dimensional Action: because of the dimension of deep beam they behave as two-
dimensional action rather than one-dimensional action.

⏺Plane Section Do Not Remain Plane: the assumption of plane section remains plane cannot
be used in the deep beam design and The strain distribution is no longer linear.

⏺Shear Deformation: the shear deformation cannot be neglected as The stress distribution is not linear even in the elastic stage and At the ultimate limit state the
shape of concrete compressive stress block is not parabolic shape again.

▶️The distribution of tensile stress at bottom fiber is constant over the span. In other word the value of tensile stress at bottom fiber at support and at mid span is only little different, for this reason in deep beam the tension reinforcement must be extend to the end of support although that region is small bending moment region (in ordinary beam we can cut off the tension reinforcement and not all of the tension reinforcement in mid span is extended to the end of support, practically only two for anchor the stirrups).

▶️The maximum tensile stress at the bottom fiber is far exceeding the magnitude of
compressive stress.

Facebook:- https://www.facebook.com/etconp/

Telegram:- https://t.me/ETCONpWORK

YouTube:- https://youtube.com/@Etconp432

💫Comment @ETCONpBot

♡ ㅤ   ❍ㅤ    ⎙ㅤ    ⌲
ˡᶦᵏᵉ   ᶜᵒᵐᵐᵉⁿᵗ  ˢᵃᵛᵉ    ˢʰᵃʳᵉ

╔═════
    🌐   join 👇
   @ETCONp
   @COTMp
╚══ ☆☆☆☆☆══════
👍5👏3❤1🕊1
🌍ሰላም በ አለም ምድር ሁሉ ይስፈን

🕊ፈጣሪ ሀገራችን ኢትዮጵያ ይጠብቅልን❤

@etconp
🕊12👍4
👉በአዲስ አበባ የመሬት አገልግሎት አሰጣጥ ለአጭር ቀን ታገደ።

በአዲስ አበባ ከተማ አስተዳደር የመሬት ልማትና አስተዳደር ቢሮ ፤ የመሬት አገልግሎት አሰጣጥ ለአጭር ቀን የታገደ መሆኑን አሳውቋል።

እገዳው ፤ ከሐምሌ 28/2ዐ15 ዓ.ም እስከ ነሐሴ 5/2ዐ15 ዓ/ም ድረስ ሲሆን ምክንያቱ ደግሞ ከቢሮ ሪፎርም ሥራ ጋር በተገናኝ የሚስተካከሉ ስራዎች ስላሉ ነው ተብሏል።

በተጠቀሰው ጊዜ ማንኛውም የመሬት አገልግሎት እንዳይሰጥ በዶ/ር ቀነዓ ያደታ (የመሬት ልማት እና አስተዳደር ቢሮ ኃላፊ) ተፈርሞ ለሁሉም ክ/ከተሞች የመሬት ልማትና አስተዳደር ፅ/ቤት የተላከው የእግድ ደብዳቤ ያሳያል

@etconp
👍7
Revit_2021_1_1.exe
689.4 MB
🔴REVIT 2021-LATEST UPDATE(2021.1.1)

The Revit 2021 updates and hotfixs are cumulative and include all changes from previously released Revit 2021 updates.

📁Issues Resolved:
Align:Improved the stability when aligning grid lines.
Alignments:Fixed the issue that Revit will hang when importing bridge model including the alignment from InfraWorks to Revit.

Content Browser:Improved stability with family load when using Load Autodesk Family.

Duct/Pipe Display:Fixed an issue that caused a gap between a pipe and fitting when using single line display with "Use Annot. Scale for Single Line Fittings" enabled in Mechanical Settings.

Energy Model:Fixed an issue that caused an energy analytical model to contain analytical surfaces with missing geometry.

Help:Fixed the issue that help link is broken when customers press F1 on the Revit plug-in.

Parameters:Fixed an issue that was caused longer than expected delays when switching views.

@etconp
👍25❤6🥰1
👉What do we mean by workability of concrete?

🌟Workability of concrete is defined as the ease and homogeneity with which a freshly mixed concrete or mortar can be mixed, placed, compacted and finished. Strictly, it is the amount of useful internal work necessary to produce 100% compaction.

⏺Another similar term used to describe a freshly prepared concrete is ‘consistency’ which is the ease with which it will flow. It is the wetness of the concrete and the measure of fluidity or mobility. Wet concretes are more workable than dry concrete, but concretes of the same consistency may vary in workability. A concrete which has high consistency and which is more mobile, need not be of right workability for a
particular job. Type of work, thickness of section, reinforcements and mode of compaction are the aspects to be considered while specifying the workability for any particular job.


Workable concrete shows very less internal friction between particles and overcomes the frictional resistance with just the amount of compacting efforts provided. Workability of the concrete depends on a number of interrelating factors. Water content, aggregate properties, use of admixtures, fineness of cement are the factors affecting workability.

1. Water content: The increase in watercontent increases the fluidity of the
concrete thus providing greater lubrication.

2. Size of aggregates: The surface area of bigger aggregates is less and hence less amount of water is required for lubricating the surface to reduce the friction. Thus the concrete having large sized aggregate is more workable (of course, within certain limits). And other properties of aggregate will affect the workability of concrete.

3. Mix proportions: Aggregate/cement ratio
is the measure of how lean or rich the concrete is. If aggregate/ cement ratio is
higher, the concrete becomes leaner. In lean concrete less paste is available for the lubrication of the aggregate, while in rich
concrete with low a/c ratio, more paste is available which makes the mix more
cohesive and hence provides better workability.

4. Use of admixtures: Use of admixtures in concrete is the major factor that affects the workability. The use of plasticizers and super-plasticizers amply increase the workability of the concrete. Air entraining
agents produce air bubbles which act as rollers between particles and provide better mobility thus improving the workability.

5. Time and temperature: Fresh concrete gets stiffened as the time flows. This is because some of the water used to mix the concrete gets evaporated and some gets absorbed
by the aggregates. Thus the workability of concrete reduces with time. This loss of workability with time is known as slump
loss. The effect of temperature on workability of concrete is noteworthy. As the temperature increases, the workability of the mix reduces.
Measurements of Workability/ workability Tests:
-Slump Test
-Compacting Factor Test
-Vee-Bee Test
-Flow Test
-Kelly Ball Test

https://m.facebook.com/etconp/
👍10❤1🏆1
👉Analysis and Design of Curved Beam

🌟Reinforced concrete curved beams arse extensively used to support circular walls of RC water tanks, curved balconies, circular domes, modern highway intersection, the rounded corners of buildings….etc.

⏺In some of these cases, large depths are needed for curved beams in order to resist high loads or to fulfill some aesthetic purposes.

⏺The analytical analysis of such members is very complex due to the fact that those members are subjected to a combined action of bending, shear and torsion. Furthermore, non-homogeneous nature of the materials involved contributes to the complexity of the problem. Therefore, it becomes necessary to employ numerical analysis procedures, such as finite element method, to satisfy safe and the economy requirements. A curved beam, loaded transversely to its plane, is subjected to torsion in addition to bending and shear. Furthermore, in deep beam the plane section does not remain plane after bending because of high stresses and warping occurs.

🌟RC curved beams are:-

▶️Supported on columns spaced at regular intervals.
▶️Torsional moments are develop at certain sections of curved beams. Maximum torsion developed at the position of zero bending moment. Maximum negative and positive moments developed supports and mid spans respectively.

🌟Design Considerations of Curved beams

▶️Torsional shear stresses create diagonal tension resulting in diagonal crack. Thus we need to provide both closed stirrups and longitudinal steel to avoid brittle fracture.
The torsional resistance of any section may be computed on the basis of an equivalent hollow section. hef , Aef ,
hef ≤ A/U & Aef = b’* h’

▶️The centerlines of the longitudinal reinforcement are taken as the centerline of the
equivalent hollow section.

▶️The limiting value of ultimate torque : to prevent diagonal compression failure,
TRD = 0.8*fcd*Aef*hef

▶️Torsional effect may be neglected when the Tsd (design torque) is less than Tc
(the torque resistance of section)
Tc = 1.2*fctd*Aef*hef

⏺However minimum web reinforcement provided  min=0.6 / fyk or Spacing of
stirrups shall not exceed Uef / 8 for torsion.

⏺If the section capacity against diagonal compression, TRD< Tsd, the section is
too small. Section should be increased.

⏺Longitudinal bars for torsion shall be distributed uniformly around the perimeter of the closed stirrups at a spacing not exceeding 350mm.

Facebook:- https://www.facebook.com/etconp/

Telegram:- https://t.me/ETCONpWORK

YouTube:- https://youtube.com/@Etconp432

💫Comment @ETCONpBot

♡ ㅤ   ❍ㅤ    ⎙ㅤ    ⌲
ˡᶦᵏᵉ   ᶜᵒᵐᵐᵉⁿᵗ  ˢᵃᵛᵉ    ˢʰᵃʳᵉ

╔═════
    🌐   join 👇
   @ETCONp
   @COTMp
╚══ ☆☆☆☆☆══════
👍7👏2
ሐምሌ.pdf
14.2 MB
👉የሐምሌ ወር 2015 ዜና መንገድ ሁለተኛ እትም የእግረኛ መንገድ ግንባታ ሥራዎችን ዳስሳለች፣

🌟እንዲያነቡ ተጋብዘዋል

Via Addis Ababa City Roads Authority (AACRA)

@etconp
🙏6👍1
👉በከተማችን ቸል የተባለ ነገር ግን በአሰቃቂ ሁኔታ የበርካቶችን እየቀጠፈ የሚገኘው …

ምንም አይነት የደህንነት መጠበቂያ (balustrade) ሳይኖር የሚካሄድ ግንባታ አንዱ ነው ፡፡

የምትመለከቱት በመንገዳችን ላይ በተንቀሳቃሽ ስልክ ያስቀረነውና 22 አውራሪስ ሆቴል ፊት ለፊት እየተካሄደ ያለ ግንባታ ነው፡፡

በትላንትናው እለት በዚሁ በመዲናችን አዲስ አበባ ከደንበል ወደ መስቀል ፍላወር በሚወስደው መንገድ ላይ ከተመሳሳይ ምንም አይነት የደህንነት መጠበቂያ ካልነበረው ግንባታ ላይ የተናደ የተለያየ የግንባታ ቁሳቁስ የአንድ እናት ህይወት መቅጠፉ ይታወሳል፡፡

የከተማ አስተዳደሩና የሚመለከተው አካል ጉዳዩን ትኩረት ያድርግበት መልእክታችን ነው፡፡

Via Sheger Times

@etconp
👍9💯1
👉ለተመራቂዎች ....

ይህን የአልበርት አንስታይን የ ዩኒቨርሲቲ rejection letter ባየሁ ቁጥር አንድ ነገር ያስታውሰኛል::

10ኛ ክፍል እያለሁ አማርኛ የቤት ስራ ይሰጠናል:: የቤት ስራውም ሰለ ስርአተ ነጥብ ነበር:: የተለያዩ አረፍተነገሮች ተሰተዋል እና እነዚህን አረፍተነገሮች ላይ ትክክለኛ ስርአተ ነጥብ በትክክለኛ ቦታው ማስገባት ነበር:: እናም በሚቀጥለው ቀን ጥያቄዎቹን ከመምህራችን ጋር አብረን በጋራ እንሰራለን:: ልክ 3ተኝው ጥያቄ ላይ ስንደርስ መህራችን አንዱን ተማሪ ስሙን ጠሩና ምን አይነት ስርአተ ነጥብ እንደሚገባ ጠየቁት:: ተማሪውም “የጥያቄ ምልክት” ብሎ መለሰ:: መልሱ ትክክል ነበር:: መህሩም ለምን የጥያቄ ምልክት እንዳስገባ ሲጠይቁት: ልጁም “ጥያቄውን ደጋግሜ ሳነበው አልገባ ሲለኝ ጥያቄ ምልክት ቁጭ አደረኩበት” ብሎ ሁላችንንም በሳቅ ገደለን:: ልክ ሳቃችንን ስንጨርስ መምህሩም “ጥያቄውን ስታነበው ቢገባህ ኖሮ ምን አይነት የስርአተ ነጥብ ነበር የምታደርግበት?” ብለው ጠየቁት:: ተማሪውም “እሱማ ግልፅ ነው አራት ነጥብ ነዋ” ብሎ እንደገና አሳቀን::
*******
ይህን የአልበርት አንስታይን rejec
tion letter የሚያስገርመኝ ዩኒቨርስቲ እንዳይገባ ብቁ ሆኖ አለመገኘቱና deny መደረጉ ሳይሆን በሁለተኛው paragraph ላይ ስለአልበርት አንስታይን theory ኮሚቴው የሰጠው አስተያዬት ነው:: “ስለ ብርሃን ተፈጥሮ: ስለ ጊዜና ቦት መስተጋብር (nature of light, fundamental connection between time and space) የደረስክበት ድምዳሜ ወጣ ያለ ነው:: ከፊዚክስ ይልቅ ወደ ስነጥበብ (art) የሚያደላ ሆኖ አገኝተነዋል::” ይላል:: ለነገሩ በጊዜው ክነበረው
የሳይንስ ግኝት አንፃር የሱን theory መረዳት በጣም ከባድ ነበር:: ነገር ግን እነርሱ አልተረዱትም ማለት ትክክል አይደለም ወይም ደግሞ artistic ነው ብሎ ማጣጣል ይከብዳል:: ይህን ደብዳቤ የፃፉት የኮሚቴ አባላት አሁን በህይወት ቢኖሩና አስተያዬታቸውን ቢያዩት እንዴት እንደሚሸማቀቁ ለመገመት አይከብደም:: ልክ እንድ 10ኛ የክፍል ጏደኛችን ካልገባቸው ጥያቄ ምልክት አድርግውበት ቢያልፉ ብዙ ነገር ያተርፉ ነበር:: ሰው ባልገባው ነገር ላይ አስተያዬት ሲሰጥ ይህ ልጅ ትዝ ይለኛል:: ለምን ጥያቄ ምልክት አድርገው አያልፉትም እላለሁ::
*****
በ1875 እኤአ ኒኮላ ተስላ G
raz University of Technology ተማሪ እያለ መምህራቸው ዳይናሞ አምጥቶ ክፍል ውስጥ ያስተምራል:: “ዳይናሞው እንደ ጄኔሬተር እና እንደ ሞተር ያገለግላል.....” እያለ እያስረዳ: በመሃል ተስላ ብድግ ብሎ “ሃይል ያባክናል (it wastes energy)” ብሎ ሃሳቡን ገለፀ:: መምህሩ ግራ ተጋብቶ እንዲያብራራ ይጠይቀዋል:: ተስላም “በጣም ብዙ ስብቀት (friction) አለው:: commutatorን ብናስወግደው ማሽኑ ሃይል አያባክንም እንዲሁም more efficient ይሆናል::” አለ::

መምህሩም “እንዴት ካለ commutator የሚሽከረከር electromagnetic field እንፈጥራለን?” ብሎ ጠየቀው:: በጊዜው በጣም ከባድና የማይሞከር ነገር ነበር የሚመስለው:: ኒኮላ ተስላም “አላቅም!” ብሎ መለሰ:: መምህሩም “እንደዚህ አይነቱን ነገር አሳካለሁ ብለህ ተስፋ አታድርግ” ብሎ ክፍል ውስጥ ተሳለቀበት:: ነገር ግን ከብዙ ምርምርና ድካም በሗላ ተስላ ተስፋ አታድርግ ተብሎ የተነገረውን ነገር ማሳካት ብቻ ሳይሆን ሌሎች ድንቅ የቴክኖሎጂና ሳይንስ ውጤቶችን አበረከተ:: የኒኮላ ተስላ ግኝቶች አሁን አለማችን ላለችበት ደረጃ እንድትደርስ ጉልህ አስተዋፅኦ አድርገዋል::
*******
To put into a nutsh
ell, ሰዎች የሆነ ነገር ማሳካት አትችልም ብለው ሲነግሩህ የአንተን አለመቻል ሳይሆን የራሳቸውን አቅመ-ቢስነት: የራሳቸውን አለመቻል እየነገሩህ ነው:: ምክንያቱም አንተን የሚለኩህ በራሳቸው አለመቻልና አቅመ-ቢስነት ነው:: ራስህን የምታውቀው አንተና አንተ ብቻ ነክ:: አላማህን ለማሳካት በርትተህ ስራ::

Via ናርዶስ ብርሃኑ

@etconp
👍29🥰3🕊2🙏1