ታምራት  ፕሌት እና ጄቦልት አቅራቢ

📌ፕሌትና ጄቦልት በፈለጉት አይነት የተዘጋጀ አለን

♧ ሁሉን በአንድ ቦታ ለሁሉም ቅርብ

♧ ምስክራችን ስራችን

📍ኢትዮጵያ ዉስጥ የትም እንልክሎታለን

♧ ይደውሉልን ያማክሩን

0904040477
0994941708

👉የአልጄሪያ ፈጣን ዕድገት
በ50 ቢሊየን ዶላር፤ 50 ሜጋ ፕሮጀክቶች

💫በአልጄሪያ መጠነ ሰፊ ሥራዎች እየተከናወኑ ነው፦ የአልጄሪያ ብሔራዊ የልማት መሣሪያዎች ፈንድ (ሲኤንኢዲ) በ6.4 ትሪሊየን ዲናር (50 ቢሊዮን ዶላር ገደማ) ወጪ 50 ቁልፍ ሜጋ ፕሮጀክቶችን እያከናወነ ነው።

🏷ቁልፍ ሴክተሮች፦

⦁ ህዝብ ተኮር ሥራዎች እና መሠረተ ልማትን የሚያሳድጉ 33 ፕሮጀክቶች፤

⦁ በውኃ የኃይል ልማት ላይ ያተኮሩ 11 ፕሮጀክቶች፤

⦁ የቤት መሰረተ ልማት እና የከተማ ፕላንን እየቀየሩ ያሉ 6 ፕሮጀክቶች፤

⭐️በትግበራ ላይ ያሉ ሜጋ ፕሮጀክቶች፡-

⦁ በቅደም ተከተል ከ950 ኪ.ሜ እና ከ420 ኪ.ሜ በላይ ርዝመት ያላቸው ሁለት አዳዲስ የባቡር መስመሮች፤

⦁ የንጹህ መጠጥ ውኃ፦ አራት የባህር ጨዋማ ውኃን የሚያጣሩ ፋብሪካዎች ወደ ሥራ የገቡ ሲሆን አምስተኛውም በመጨረሻው የግንባታ ምዕራፍ ላይ ይገኛል፤

⦁ አልጀርስ ሜትሮ፦ አየር መንገዱን ከሀገሪቱ ዋና ከተማ ደቡባዊ ክፍል ጋር የሚያገናኝ ቁልፍ የማስፋፊያ ሥራ፤

Via ስፑትኒክ ኢትዮጵያ

@etconp

👉Marginal Cost and Marginal Revenue Method (MC and MR method)

💫According to this method there are two conditions of equilibrium of firm.

i. MC = MR
ii. Slope of MC > slope of MR

(Diagram of MC and MR method)

We can explain this method with the help of a diagram, where marginal cost curve is intersecting marginal revenue at two points E' and E. So at both points, marginal cost is equal to marginal revenue. But the second condition of equilibrium is being satisfied only at point E where slope of
We know that a firm will be in equilibrium when it is earning maximum profits. We shall see presently
that for a firm, to make maximum profits. two conditions arc essential:
(i) Marginal Revenue = Marginal Cost. and (ii) MC curve cuts MR curve from below at the
equilibrium point. It is obvious that total profits can be increased by expanding output as long as the addition to the total revenue resulting from the sale of extra unit of output is greater than the addition io the total cost caused by producing an extra output. Now the addition to total revenue and total cost due to an extra unit of output are nothing else but marginal revenue and marginal cost respectively. Thus. a firm will go on expanding output as long as marginal revenue exceeds marginal cost of production. If. at any output. marginal revenue falls short of marginal cost.  if an additional unit of output adds less to total revenue than to total cost. the firm will contract output to avoid losses and thus increase its profits” The level of output when’ and  are equal is the profit

The whole argument can be explained with the  where MC is the marginal cost curve and MR the marginal revenue curve. AC ami AR are the average cost and average revenue curves respectively. At the output OM. marginal cost equals marginal revenue (MR and MC curves intersect at E above this point). This represents the point of maximum profits and hence of equilibrium. At outputs smaller than OM. marginal revenue exceeds marginal cost and hence-there is scope for increasing profits by increasing output. For example, at output OL, marginal revenue is LG and the marginal cost is LH. and LG is greater than LH. It means that by producing the L1h unit, the firm is adding more to revenue than to its cost and, therefore, it will be profitable for it to produce the L1h unit. Similarly, for evcry other unit till the Mth one, the marginal revenue exceeds marginal cost, and, therefore, the firm can increase its total profits by producing up to OM output. If the firm stops producing at OL, the units of output which could have added more money to thc firm’s revenue than to its cost would not have been produced and profits would have been smaller by the area GHE than they could have been. Thus, a firm has an incentive to produce up to 0 1 level of output.

Hence, we conclude that firm’s profits at OM output are the maximum and that’ limn when laminar Ctlt libidinal This is one condition which is necessary but which is not sufficient for equilibrium.  the total profits earned by the firm in the equilibrium position The easily found. At output OM, the average cost iDM while the average revenue is QM. Therefore. the profit per unit will be equal to QD and the total profits will he equal to the rectangle DIRT. At an equilibrium position, the  curve  t cut the The condition that for a firm.

Librium marginal cost must equal marginal revenue is no doubt a necessary condition but not a sufficient condition of equilibrium. For attaining equilibrium, a second condition must also be satisfied, ‘.;z., that the marginal cost (Me) curve must cut the marginal revenue (MR) curve from below at the point of equilibrium. This means that, beyond the equilibrium output, marginal cost must be greater than marginal revenue. If this condition is not met. a firm will not be earning maximum profits and hence will not be in equilibrium.

@etconp

👉የከተማ ንድፍ መመርያ

💫 "Principles of Good Urban Design For NewYork City" የሚል ለከተማ ነዳፊዎች እንዲሁም ለተማሪዎች የሚሆን ባለ 35 ገጽ ጠቃሚ መጽሀፍ ከላይ በ ፒዲኤፍ ፋይል ተያይዟል አውርዳቹ ተጠቀሙበት።

📜Tool for everyone interested in creating better neighborhoods through design.

@etconp

👉TYPES OF BEAM

💫1. Simply Supported Beam

⏺Support Type: One end has a hinge/pin, and the other has a roller.

⏺Behavior: It can resist vertical loads but allows rotation and horizontal movement at the roller end.

⏺Common Use: Bridges, basic structural beams.

💫2. Fixed Beam (or Built-in Beam)

⏺Support Type: Both ends are fixed (rigidly held).

⏺Behavior: It resists vertical loads, horizontal forces, and moments (rotation is restricted).

⏺Common Use: Building frames, rigid structures.

💫3. Cantilever Beam

⏺Support Type: One end is fixed, and the other end is free.

⏺Behavior: The fixed end resists vertical load, horizontal forces, and moments. The free end can deflect and rotate.

⏺Common Use: Balconies, overhangs, diving boards.

💫4. Overhanging Beam

⏺Support Type: Like a simply supported beam but with one or both ends extending beyond the support.

⏺Behavior: Combines features of simply supported and cantilever beams.

⏺Common Use: Bridges, balconies with overhangs.

💫5. Continuous Beam

⏺Support Type: Supported on more than two supports.

⏺Behavior: Reduces bending moment at mid-span, more stable under varying loads.

⏺Common Use: Long-span bridges, multi-span floors.

@etconp

👉 INTERCON Construction Chemicals 

● Concrete Admixtures
● Bonding Agents
● Waterproofings
● Wall Putty, Prime Coat
● Concrete Repair Mortar
● Floor hardener, Epoxy
● Grout, Self-level mortar
● Quartz paint, Contextra
● Tile Adhesive & Tile Joint Fillers 
● Geotextiles and other construction chemicals and materials

Tel: 0961955555
Address: Signal, around signal mall

#ADVERTISEMENT

🏭🏠TSEGAYE and YOHANNES J-ቦልት & PLATE 🏚🏗 🌁🌆

🧿 OUR SERVICES ⤵️

🔲Plate

⚙️  J-Bolt

⚓Anchor Bolt

➽Tie Rod

Phone : 🤳0938494506 
              🤳 0951087077
              🤳 0929044037
እናመሰግናለን::
👉አድራሻ፦  መርካቶ ምንአለሽ ተራ ከጭድ ተራ ከፍ ብሎ

https://t.me/tsegaye2016Jbolt

👉‎ ADVANTAGES OF SOLID SLAB OVER HOLLOW SLAB ⤵️
‎
💫Solid and Hollow slabs are two of types of Structural slab used in Constructions, both have distinct differences and similarities.

🚧Below are the advantages of solid slabs over hollow slabs:
‎
🏷‎ADVANTAGES OF SOLID SLABS

‎1. HIGHER LOAD-BEARING CAPACITY: Solid slabs can support heavier loads due to their continuous, solid structure.
‎
‎2. IMPROVED STRUCTURAL INTEGRITY: Solid slabs provide better structural stability and resistance to cracking and deformation.
‎
‎3. ENHANCED FIRE RESISTANCE: Solid slabs offer superior fire resistance due to their non-combustible nature and lack of voids.
‎
‎4. BETTER SOUND INSULATION: Solid slabs can provide better sound insulation due to their mass and density.
‎
‎5. DURABILITY: Solid slabs are highly durable and can withstand harsh environmental conditions, including heavy traffic and extreme weather.
‎
‎6. SIMPLIFIED CONSTRUCTION: Solid slabs can be simpler to construct, as they don't require the creation of voids or hollow sections.
‎
‎7. IMPROVED THERMAL MASS: Solid slabs can provide better thermal mass, helping to regulate indoor temperatures.
‎
🏷‎WHEN TO CHOOSE SOLID SLABS?

‎1. HEAVY LOAD APPLICATIONS: Solid slabs are suitable for structures with heavy loads, such as industrial buildings, warehouses, or high-rise buildings.
‎
‎2. HIGH-TRAFFIC AREAS: Solid slabs can withstand heavy foot traffic and are often used in commercial or public buildings.
‎
‎3. SPECIALIZED APPLICATIONS: Solid slabs may be preferred for applications requiring high durability, fire resistance, or sound insulation, such as hospitals, schools, or residential buildings.
‎
⏺‎The choice between solid slabs and hollow slabs depends on the specific project requirements, including load-bearing capacity, structural integrity, and budget constraints.

@etconp

👉Project Manager 👷

1️⃣ Project Manager (PM) Tasks;

💫1.Overall Project Oversight: The Project Manager is responsible for the entire lifecycle of the project, from planning and initiation through execution, monitoring, and closing. They ensure that the project meets its objectives, is completed on time within budget.

💫2.Project Planning: The PM develops comprehensive project plans that outline scope, schedule, cost, quality, and risk management strategies.

💫3.Stakeholder Management: Project Managers work closely with various stakeholders, including clients, architects, engineers, and contractors.

💫4.Budget Management: The PM is responsible for creating and managing the project budget, including cost estimates, tracking expenses, and making adjustments to keep the project within financial constraints.

💫5.Risk Management: Identifying potential risks and developing mitigation strategies is a key task for Project Managers. They monitor risks throughout the project and take necessary actions to address them.

💫6.Contract Management: Project Managers oversee contracts with vendors, suppliers, and subcontractors, ensuring that all parties fulfill their contractual obligations.

💫7.Communication and Reporting: The PM is the primary point of contact for communication among all parties involved in the project.

💫8.Quality Assurance: Ensuring that the project meets the required quality standards is a critical responsibility for the Project Manager.

@etconp