👆👆👆👆👆👆👆👆👆👆
.
👉ይቺ ናት ኢትዮጵያ ይቺ ናት ሀገሬ @ETCONp
:
▶️ኢትዮጵያ ሀገራችንን በበጎ ስራ እናገልግል የምህንድስና ሙያን ወደ ከፍታው እንመልስ!!
፡
🙏"ፈጣሪ ኢትዮጵያ እና ህዝቦቿን አብዝቶ ይባርክ!!"🙏
.
👉ይቺ ናት ኢትዮጵያ ይቺ ናት ሀገሬ @ETCONp
:
▶️ኢትዮጵያ ሀገራችንን በበጎ ስራ እናገልግል የምህንድስና ሙያን ወደ ከፍታው እንመልስ!!
፡
🙏"ፈጣሪ ኢትዮጵያ እና ህዝቦቿን አብዝቶ ይባርክ!!"🙏
👉8 CAUSES OF CRACKS IN CONCRETE YOU SHOULD KNOW
:
▶️Cracking is one of the most common problems in concrete and it should be avoided seriously.
*Different causes of cracks in concrete are described below:
.
1. SHRINKAGE:
*Shrinkage is one of the major causes of cracking in hardened concrete.
*In drying shrinkage, the volume of concrete is gradually decreased and if the component is restrained against free movement, tensile stresses are developed which causes cracks.
.
2. TEMPERATURE CHANGES:
The temperature variation in concrete results in the differential volume change.
*When the tensile strain capacity of concrete exceeds due to the differential volume change, it will crack.
.
3. CHEMICAL REACTION:
Due to the alkaline nature of cement, it reacts with the carbon dioxide (CO2) present in the atmosphere resulting in an appreciable increase in the volume of the materials which
finally leads to cracking.
.
4. POOR CONSTRUCTION PRACTICES:
Poor construction practices such as adding excessive water to the mix, lack of curing, poor compaction, using low-grade materials, unreasonable placements of construction joints etc. are also responsible for cracking in concrete.
.
5. ERRORS IN DESIGN & DETAILING:
Errors in design and detailing such as an inadequate amount of reinforcement, improper design of foundation, precast members and slabs, improper selection of materials, lack of sufficient contraction joints etc may result in excessive cracking.
.
6. CONSTRUCTION OVERLOADS & EARLY
FORMWORK REMOVAL:
The load induced in the structure during construction can also lead to cracking especially at the younger stage when the
formwork is removed earlier.
.
7. ELASTIC DEFORMATION AND CREEP:
The different components of the building such as wall, column, beam. slab etc undergo elastic deformation when loaded.
*The deformation of concrete depends on the type of building materials used in the constructio such as bricks, cement concrete blocks etc.
*This unusual deformation of concrete results
in cracking.
.
8. CORROSION OF CONCRETE:
The corrosion of steel develops a huge amount of iron oxides and hydroxide that have a much greater volume than the volume of metallic iron. Hence the volume is increased
:
https://t.me/COTMp
:
▶️Cracking is one of the most common problems in concrete and it should be avoided seriously.
*Different causes of cracks in concrete are described below:
.
1. SHRINKAGE:
*Shrinkage is one of the major causes of cracking in hardened concrete.
*In drying shrinkage, the volume of concrete is gradually decreased and if the component is restrained against free movement, tensile stresses are developed which causes cracks.
.
2. TEMPERATURE CHANGES:
The temperature variation in concrete results in the differential volume change.
*When the tensile strain capacity of concrete exceeds due to the differential volume change, it will crack.
.
3. CHEMICAL REACTION:
Due to the alkaline nature of cement, it reacts with the carbon dioxide (CO2) present in the atmosphere resulting in an appreciable increase in the volume of the materials which
finally leads to cracking.
.
4. POOR CONSTRUCTION PRACTICES:
Poor construction practices such as adding excessive water to the mix, lack of curing, poor compaction, using low-grade materials, unreasonable placements of construction joints etc. are also responsible for cracking in concrete.
.
5. ERRORS IN DESIGN & DETAILING:
Errors in design and detailing such as an inadequate amount of reinforcement, improper design of foundation, precast members and slabs, improper selection of materials, lack of sufficient contraction joints etc may result in excessive cracking.
.
6. CONSTRUCTION OVERLOADS & EARLY
FORMWORK REMOVAL:
The load induced in the structure during construction can also lead to cracking especially at the younger stage when the
formwork is removed earlier.
.
7. ELASTIC DEFORMATION AND CREEP:
The different components of the building such as wall, column, beam. slab etc undergo elastic deformation when loaded.
*The deformation of concrete depends on the type of building materials used in the constructio such as bricks, cement concrete blocks etc.
*This unusual deformation of concrete results
in cracking.
.
8. CORROSION OF CONCRETE:
The corrosion of steel develops a huge amount of iron oxides and hydroxide that have a much greater volume than the volume of metallic iron. Hence the volume is increased
:
https://t.me/COTMp
Telegram
ETCONp Discussion
📩ለማነኛውም ሀሳብ እና አስተያየት @Philemona7
✌️ይህ የ @etconp መወያያ ግሩፓቹ ነው።
✋This is discussion group of @ETCONpWORK
.
🔖ማሳሰብያ ...
.
⚡️ግሩፑ ላይ ማነኛውም ከ ኮንስትራክሽን ጉዳዮች ውጪ መለጠፍ በፍፁም አይፈቀድም!
@ETCONpBOT ፃፉልን እናመሰግናለን🙏
✌️ይህ የ @etconp መወያያ ግሩፓቹ ነው።
✋This is discussion group of @ETCONpWORK
.
🔖ማሳሰብያ ...
.
⚡️ግሩፑ ላይ ማነኛውም ከ ኮንስትራክሽን ጉዳዮች ውጪ መለጠፍ በፍፁም አይፈቀድም!
@ETCONpBOT ፃፉልን እናመሰግናለን🙏
Forwarded from Deleted Account
Tanzania_Field Testing Manual (2003).pdf
8.1 MB
Forwarded from Deleted Account
Tanzania_Laboratory Testing Manual (2000).pdf
8.2 MB
👉Types of failure @ETCONp
.
▶️Structural failure can occur from many types of problems, most of which are unique to different industries and structural types. However, most can be traced to one of five main causes.
.
▶️The first is that the structure is not strong and tough enough to support the load, due to either its size, shape, or choice of material. If the structure or component is not strong enough, catastrophic failure can occur when the structure is stressed beyond its critical stress level.
.
▶️The second type of failure is from fatigue or corrosion, caused by instability in the structure’s geometry, design or material properties.
*These failures usually begin when cracks form at stress points, such as squared corners or bolt holes too close to the material's edge.
*These cracks grow as the material is repeatedly stressed and unloaded (cyclic loading), eventually reaching a critical length and causing the structure to suddenly fail under normal loading conditions.
.
▶️The third type of failure is caused by manufacturing errors, including improper selection of materials, incorrect sizing, improper heat treating , failing to adhere to the design, or shoddy workmanship.
*This type of failure can occur at any time and is usually
unpredictable.
:
▶️The fourth type of failure is from the use of defective materials.
*This type of failure is also unpredictable, since the material may have been improperly manufactured or damaged from prior use.
:
▶️The fifth cause of failure is from lack of consideration of unexpected problems.
*This type of failure can be caused by events such as vandalism, sabotage, or natural disasters. It can also occur if those who use and maintain the construction are not properly trained and overstress the structure.
👉Reasons Structures Fail @ETCONp
▶️Defective construction that causes failure may be due to
numerous reasons that may not be easy to predict before or
during the construction. The major causes of structural
failure are defective designs that have not determined the
actual loading conditions on the structural elements. Inferior
construction materials may also be the cause since the
loads are calculated for materials of specific characteristics.
Structure may fail even if the design is satisfactory, but the
materials are not able to withstand the loads. Employment of
unskilled labor on construction work is another reason for
structural failures. Therefore, it is important that the owners,
designers, and builders are fully conscious of the reasons of
failure, and undertake all preventive measures
.
. https://t.me/COTMp
.
▶️Structural failure can occur from many types of problems, most of which are unique to different industries and structural types. However, most can be traced to one of five main causes.
.
▶️The first is that the structure is not strong and tough enough to support the load, due to either its size, shape, or choice of material. If the structure or component is not strong enough, catastrophic failure can occur when the structure is stressed beyond its critical stress level.
.
▶️The second type of failure is from fatigue or corrosion, caused by instability in the structure’s geometry, design or material properties.
*These failures usually begin when cracks form at stress points, such as squared corners or bolt holes too close to the material's edge.
*These cracks grow as the material is repeatedly stressed and unloaded (cyclic loading), eventually reaching a critical length and causing the structure to suddenly fail under normal loading conditions.
.
▶️The third type of failure is caused by manufacturing errors, including improper selection of materials, incorrect sizing, improper heat treating , failing to adhere to the design, or shoddy workmanship.
*This type of failure can occur at any time and is usually
unpredictable.
:
▶️The fourth type of failure is from the use of defective materials.
*This type of failure is also unpredictable, since the material may have been improperly manufactured or damaged from prior use.
:
▶️The fifth cause of failure is from lack of consideration of unexpected problems.
*This type of failure can be caused by events such as vandalism, sabotage, or natural disasters. It can also occur if those who use and maintain the construction are not properly trained and overstress the structure.
👉Reasons Structures Fail @ETCONp
▶️Defective construction that causes failure may be due to
numerous reasons that may not be easy to predict before or
during the construction. The major causes of structural
failure are defective designs that have not determined the
actual loading conditions on the structural elements. Inferior
construction materials may also be the cause since the
loads are calculated for materials of specific characteristics.
Structure may fail even if the design is satisfactory, but the
materials are not able to withstand the loads. Employment of
unskilled labor on construction work is another reason for
structural failures. Therefore, it is important that the owners,
designers, and builders are fully conscious of the reasons of
failure, and undertake all preventive measures
.
. https://t.me/COTMp
Telegram
ETCONp Discussion
📩ለማነኛውም ሀሳብ እና አስተያየት @Philemona7
✌️ይህ የ @etconp መወያያ ግሩፓቹ ነው።
✋This is discussion group of @ETCONpWORK
.
🔖ማሳሰብያ ...
.
⚡️ግሩፑ ላይ ማነኛውም ከ ኮንስትራክሽን ጉዳዮች ውጪ መለጠፍ በፍፁም አይፈቀድም!
@ETCONpBOT ፃፉልን እናመሰግናለን🙏
✌️ይህ የ @etconp መወያያ ግሩፓቹ ነው።
✋This is discussion group of @ETCONpWORK
.
🔖ማሳሰብያ ...
.
⚡️ግሩፑ ላይ ማነኛውም ከ ኮንስትራክሽን ጉዳዮች ውጪ መለጠፍ በፍፁም አይፈቀድም!
@ETCONpBOT ፃፉልን እናመሰግናለን🙏
👍1
Jakarta Indonesia 🇮🇩
ውብ ምሽት ተመኘን
كنا نتمنى أمسية جميلة
我們希望有一個美麗的夜晚
हमने एक खूबसूरत शाम की कामना की
We wished a beautiful evening
Мы пожелали прекрасного вечера
@ETCONp
ውብ ምሽት ተመኘን
كنا نتمنى أمسية جميلة
我們希望有一個美麗的夜晚
हमने एक खूबसूरत शाम की कामना की
We wished a beautiful evening
Мы пожелали прекрасного вечера
@ETCONp