👉High strength concrete @COTMp
.
➡High strength concrete (HSC) may be defined as
concrete with a specified characteristic cube
strength between 60 and 100 N/mm , although
higher strengths have been achieved and used.
.
▶Strength levels of 80 to 100 N/mm and even
higher are being used for both precast and in-
situ work in All over the world.
.
▶The main applications for HSC in-situ concrete construction are in offshore structures, columns for tall buildings, long-span bridges and other highway structures
.
▶The main advantage is the reduction in size of
compression elements and/or the amount of
longitudinal reinforcement required.
.
▶The methods and technology for producing high strength concrete are not substantially different
from those required for normal strength concrete.
The target water/cement ratio should be in the
range 0.30–0.35 or even lower. HSC can be
produced with all of the cements and cement
replacements (additions). A wide range of aggregates can be used
though crushed rock aggregates (of suitably high crushing value) are preferable.
Superplasticisers / high range water reducers
should be used to achieve maximum water reduction, although plasticisers may be adequate for lower strength HSC (C-60 to C-70). Silica fume (microsilica) or metakaoline can be used to enhance the strength at high levels (C80 and
above), but is not needed generally at the lower
end (C60 to C80).
The terms "High performance concrete" and "High strength concrete" are often taken to mean the same thing. However, as indicated, "High performance" strictly relates to a concrete that
has been designed to have good specific
characteristics, such as high resistance to
chloride ingress or high abrasion resistance. As a
result it may also have a high strength, but this
is not the main consideration.
.
🚩👇👇👇👇👇
Join for more updates via the link below;
t.me/COTMp
👆👆👆👆👆
🅾አሁኑኑ Join በማረግ እና ለጓደኛዎ እና ለሚያቁት ሁሉ ሼር ያድርጉ።
.
➡High strength concrete (HSC) may be defined as
concrete with a specified characteristic cube
strength between 60 and 100 N/mm , although
higher strengths have been achieved and used.
.
▶Strength levels of 80 to 100 N/mm and even
higher are being used for both precast and in-
situ work in All over the world.
.
▶The main applications for HSC in-situ concrete construction are in offshore structures, columns for tall buildings, long-span bridges and other highway structures
.
▶The main advantage is the reduction in size of
compression elements and/or the amount of
longitudinal reinforcement required.
.
▶The methods and technology for producing high strength concrete are not substantially different
from those required for normal strength concrete.
The target water/cement ratio should be in the
range 0.30–0.35 or even lower. HSC can be
produced with all of the cements and cement
replacements (additions). A wide range of aggregates can be used
though crushed rock aggregates (of suitably high crushing value) are preferable.
Superplasticisers / high range water reducers
should be used to achieve maximum water reduction, although plasticisers may be adequate for lower strength HSC (C-60 to C-70). Silica fume (microsilica) or metakaoline can be used to enhance the strength at high levels (C80 and
above), but is not needed generally at the lower
end (C60 to C80).
The terms "High performance concrete" and "High strength concrete" are often taken to mean the same thing. However, as indicated, "High performance" strictly relates to a concrete that
has been designed to have good specific
characteristics, such as high resistance to
chloride ingress or high abrasion resistance. As a
result it may also have a high strength, but this
is not the main consideration.
.
🚩👇👇👇👇👇
Join for more updates via the link below;
t.me/COTMp
👆👆👆👆👆
🅾አሁኑኑ Join በማረግ እና ለጓደኛዎ እና ለሚያቁት ሁሉ ሼር ያድርጉ።
Telegram
ETCONp Discussion
📩ለማነኛውም ሀሳብ እና አስተያየት @Philemona7
✌️ይህ የ @etconp መወያያ ግሩፓቹ ነው።
✋This is discussion group of @ETCONpWORK
.
🔖ማሳሰብያ ...
.
⚡️ግሩፑ ላይ ማነኛውም ከ ኮንስትራክሽን ጉዳዮች ውጪ መለጠፍ በፍፁም አይፈቀድም!
@ETCONpBOT ፃፉልን እናመሰግናለን🙏
✌️ይህ የ @etconp መወያያ ግሩፓቹ ነው።
✋This is discussion group of @ETCONpWORK
.
🔖ማሳሰብያ ...
.
⚡️ግሩፑ ላይ ማነኛውም ከ ኮንስትራክሽን ጉዳዮች ውጪ መለጠፍ በፍፁም አይፈቀድም!
@ETCONpBOT ፃፉልን እናመሰግናለን🙏
👉TYPES OF STAIRS @COTMp
.
➡Depending upon the various arrangement of steps, stairs can be classified under following categories:
.
1. STRAIGHT STAIR:
In this stair, all the steps are arranged continuously
along in one direction. One flight may be split into
one or more than one flight by interposing a
landing. This stair can be used where narrow and
long space is available for a staircase such as
entrance, porch etc.
.
2. DOGGED-LEGGED STAIR: This stair consists of two straight flights of steps with direct turns between them. This stair is very useful where the total width of the stair is just twice the width of the steps.
.
3. OPEN NEWEL STAIR:
This type of stair consists of two or more flights
arranging a well or opening between the backward
and forward flights. When all the steps are difficult
to arrange in two flights, a short third flight of 3 to
6 steps may be provided along the direction
perpendicular to the hall. Open newel stair is mostly
adopted in the lift.
.
4. GEOMETRICAL STAIR:
This is another type of open newel stair where the
open well between the forward and the backward
flight is curved. This stair may contain different
geometrical shape. Here the change in direction is
achieved by using winders.
.
5. CIRCULAR STAIR:
In this type of stair, all the steps radiate from a newel or well hole, in the form of winders.
The circular stair is adopted at the back side of a building to access its various floors.
6. SPIRAL STAIR:
Spiral stair is very similar to a circular stair. It consists of individual steps or treads, connecting to a centre column. The overall diameter of the stair may range from 1 to 2.5 m.
.
7. QUARTER-TURN STAIR:
The quarter-turn stair can be defined as the stairs
that are turned at 90 degrees with the help of level landing.
.
8. BIFURCATED STAIR:
This type of stair is provided in modern public
buildings as well as residential buildings. In this stair, the flight is so arranged that there is a wide flight at the start which is sub-divided into narrow flights at the mid-landing. The narrow flights start from either side of the mid landing.
.
🚩👇👇👇👇👇
Join for more updates via the link below;
t.me/COTMp
👆👆👆👆👆
🅾አሁኑኑ Join በማረግ እና ለጓደኛዎ እና ለሚያቁት ሁሉ ሼር ያድርጉ።
.
➡Depending upon the various arrangement of steps, stairs can be classified under following categories:
.
1. STRAIGHT STAIR:
In this stair, all the steps are arranged continuously
along in one direction. One flight may be split into
one or more than one flight by interposing a
landing. This stair can be used where narrow and
long space is available for a staircase such as
entrance, porch etc.
.
2. DOGGED-LEGGED STAIR: This stair consists of two straight flights of steps with direct turns between them. This stair is very useful where the total width of the stair is just twice the width of the steps.
.
3. OPEN NEWEL STAIR:
This type of stair consists of two or more flights
arranging a well or opening between the backward
and forward flights. When all the steps are difficult
to arrange in two flights, a short third flight of 3 to
6 steps may be provided along the direction
perpendicular to the hall. Open newel stair is mostly
adopted in the lift.
.
4. GEOMETRICAL STAIR:
This is another type of open newel stair where the
open well between the forward and the backward
flight is curved. This stair may contain different
geometrical shape. Here the change in direction is
achieved by using winders.
.
5. CIRCULAR STAIR:
In this type of stair, all the steps radiate from a newel or well hole, in the form of winders.
The circular stair is adopted at the back side of a building to access its various floors.
6. SPIRAL STAIR:
Spiral stair is very similar to a circular stair. It consists of individual steps or treads, connecting to a centre column. The overall diameter of the stair may range from 1 to 2.5 m.
.
7. QUARTER-TURN STAIR:
The quarter-turn stair can be defined as the stairs
that are turned at 90 degrees with the help of level landing.
.
8. BIFURCATED STAIR:
This type of stair is provided in modern public
buildings as well as residential buildings. In this stair, the flight is so arranged that there is a wide flight at the start which is sub-divided into narrow flights at the mid-landing. The narrow flights start from either side of the mid landing.
.
🚩👇👇👇👇👇
Join for more updates via the link below;
t.me/COTMp
👆👆👆👆👆
🅾አሁኑኑ Join በማረግ እና ለጓደኛዎ እና ለሚያቁት ሁሉ ሼር ያድርጉ።
Telegram
ETCONp Discussion
📩ለማነኛውም ሀሳብ እና አስተያየት @Philemona7
✌️ይህ የ @etconp መወያያ ግሩፓቹ ነው።
✋This is discussion group of @ETCONpWORK
.
🔖ማሳሰብያ ...
.
⚡️ግሩፑ ላይ ማነኛውም ከ ኮንስትራክሽን ጉዳዮች ውጪ መለጠፍ በፍፁም አይፈቀድም!
@ETCONpBOT ፃፉልን እናመሰግናለን🙏
✌️ይህ የ @etconp መወያያ ግሩፓቹ ነው።
✋This is discussion group of @ETCONpWORK
.
🔖ማሳሰብያ ...
.
⚡️ግሩፑ ላይ ማነኛውም ከ ኮንስትራክሽን ጉዳዮች ውጪ መለጠፍ በፍፁም አይፈቀድም!
@ETCONpBOT ፃፉልን እናመሰግናለን🙏
👉What is standard box size? @COTMp
.
▶width*length*depth
.
1. 40*50*20cm (mostly for cement mortar)
2. 40*50*18cm (for C-25 concrete)
3. 40*50*16cm (for C-30 concrete)
4. 40*50*14cm (for C-40 concrete but depend on mix design )
.
⚡ አሁኑኑ Join በማረግ እና ለጓደኛዎ እና ለሚያቁት ሁሉ ሼር ያድርጉ።
.
▶width*length*depth
.
1. 40*50*20cm (mostly for cement mortar)
2. 40*50*18cm (for C-25 concrete)
3. 40*50*16cm (for C-30 concrete)
4. 40*50*14cm (for C-40 concrete but depend on mix design )
.
⚡ አሁኑኑ Join በማረግ እና ለጓደኛዎ እና ለሚያቁት ሁሉ ሼር ያድርጉ።
👍3👌2
👉ዛሬ ደሞ ትንሽ ስለ ግድብ እንንገራቹ @COTMp
.
▶ግድብ (Dam) ማለት ግዙፍ አካል ሲሆን የውንዝን ሸለቆ ላይ ተገንብቶ የውሃን ተፋሰስ ሙሉ በሙሉ ወይም በከፊል የሚገታ ነው።
*ይህ መግታት (blockage) በውሃ ተፋሰስ ላይ መታቆርን (reservoir) ይፍጥራል ይህም ወሃውን ለተፈለገው አገልግሎት እንዲውል ቀላል ያደርገዋል።
ይህ አጋጅ ገዝፈ አካል ወይም ግድብ ከተለያዩ ቁሶች ይሰራል ፦ ኮንክሪት፣ የድንጋይና አፈር
መደምደም (compaction) ወዘተ...
.
➡ግድብ በዋነኛነት ለነዚህ አገልግሎቶች ይገነባል፦👇
.
1- ጎርፍን ለመቆጣጠር (for flood control)
.
2- ለውሃ አቅርቦት እና የመስኖ ስራ (for water supply and
irrigation)
.
3- የኤሌትሪክ ሃይልን ለማመንጨት (for electric power generation)
.
4- የአንድን ወንዝ ፍሰት ለመመጠን እና ለመቆጣጠር - (for regulation or balancing of a river flow)
.
⚡ አሁኑኑ Join በማረግ እና ለጓደኛዎ እና ለሚያቁት ሁሉ ሼር ያድርጉ።
.
▶ግድብ (Dam) ማለት ግዙፍ አካል ሲሆን የውንዝን ሸለቆ ላይ ተገንብቶ የውሃን ተፋሰስ ሙሉ በሙሉ ወይም በከፊል የሚገታ ነው።
*ይህ መግታት (blockage) በውሃ ተፋሰስ ላይ መታቆርን (reservoir) ይፍጥራል ይህም ወሃውን ለተፈለገው አገልግሎት እንዲውል ቀላል ያደርገዋል።
ይህ አጋጅ ገዝፈ አካል ወይም ግድብ ከተለያዩ ቁሶች ይሰራል ፦ ኮንክሪት፣ የድንጋይና አፈር
መደምደም (compaction) ወዘተ...
.
➡ግድብ በዋነኛነት ለነዚህ አገልግሎቶች ይገነባል፦👇
.
1- ጎርፍን ለመቆጣጠር (for flood control)
.
2- ለውሃ አቅርቦት እና የመስኖ ስራ (for water supply and
irrigation)
.
3- የኤሌትሪክ ሃይልን ለማመንጨት (for electric power generation)
.
4- የአንድን ወንዝ ፍሰት ለመመጠን እና ለመቆጣጠር - (for regulation or balancing of a river flow)
.
⚡ አሁኑኑ Join በማረግ እና ለጓደኛዎ እና ለሚያቁት ሁሉ ሼር ያድርጉ።
👍1
👉Mix design can be divided into following two categories
.
➡ 1. Design mix concrete
.
➡ 2. Nominal mix concrete.
.
1. DESIGN MIX CONCRETE:
.
*When the proportions of concrete ingredients are decided by adopting certain established relationships (based on assumptions from a lot
of experiments) to produce the concrete it is known as design mix concrete.
*In design mix concrete, it is assumed that compressive strength of concrete is totally
dependent on the water- cement ratio.
.
2. NOMINAL MIX CONCRETE:
.
*When the concrete is produced by taking standard arbitrary proportions of concrete ingredients, it is known as nominal mix concrete. *This method is generally used when the quality control requirement for design mixes are difficult to execute. As we have explained for normal work, nominal mix concrete can be designed by taking cement, fine aggregate and coarse aggregate in
the ratio of 1 : n : 2n.
.
👇👇👇👇👇
Join for more updates via the link below;
t.me/COTMp
👆👆👆👆👆
⚡ አሁኑኑ Join በማረግ እና ለጓደኛዎ እና ለሚያቁት ሁሉ ሼር ያድርጉ።
.
➡ 1. Design mix concrete
.
➡ 2. Nominal mix concrete.
.
1. DESIGN MIX CONCRETE:
.
*When the proportions of concrete ingredients are decided by adopting certain established relationships (based on assumptions from a lot
of experiments) to produce the concrete it is known as design mix concrete.
*In design mix concrete, it is assumed that compressive strength of concrete is totally
dependent on the water- cement ratio.
.
2. NOMINAL MIX CONCRETE:
.
*When the concrete is produced by taking standard arbitrary proportions of concrete ingredients, it is known as nominal mix concrete. *This method is generally used when the quality control requirement for design mixes are difficult to execute. As we have explained for normal work, nominal mix concrete can be designed by taking cement, fine aggregate and coarse aggregate in
the ratio of 1 : n : 2n.
.
👇👇👇👇👇
Join for more updates via the link below;
t.me/COTMp
👆👆👆👆👆
⚡ አሁኑኑ Join በማረግ እና ለጓደኛዎ እና ለሚያቁት ሁሉ ሼር ያድርጉ።
Telegram
ETCONp Discussion
📩ለማነኛውም ሀሳብ እና አስተያየት @Philemona7
✌️ይህ የ @etconp መወያያ ግሩፓቹ ነው።
✋This is discussion group of @ETCONpWORK
.
🔖ማሳሰብያ ...
.
⚡️ግሩፑ ላይ ማነኛውም ከ ኮንስትራክሽን ጉዳዮች ውጪ መለጠፍ በፍፁም አይፈቀድም!
@ETCONpBOT ፃፉልን እናመሰግናለን🙏
✌️ይህ የ @etconp መወያያ ግሩፓቹ ነው።
✋This is discussion group of @ETCONpWORK
.
🔖ማሳሰብያ ...
.
⚡️ግሩፑ ላይ ማነኛውም ከ ኮንስትራክሽን ጉዳዮች ውጪ መለጠፍ በፍፁም አይፈቀድም!
@ETCONpBOT ፃፉልን እናመሰግናለን🙏
👉Tip For Today @COTMp
.
1.1 Classification of Construction Materials
Construction materials can be classified into:
I) Metallic and Non-metallic
a. Non-metallic
- Cementing materials
- Concrete
- Timber
- Stone
- Plastics
- Ceramics
b. Metallic
- Ferrous
• Wrought iron
• Cast iron
• Steel
- Non Ferrous
• Aluminium
• Copper
• Lead
• Zinc
II) Based on their physical Nature:
a) Solid
b) Liquid
c) Gaseous
III) Based on their mode of manufacture
a) Naturally occurring materials
b) Industrially produced materials
c) Materials produced at construction site
1.2 Properties of Materials
a) Physical properties
• Density and specific gravity
•Mechanical properties
• Thermal properties
• Acoustical properties
b) Chemical properties
• Corrosion Here only the mechanical properties are dealt with since they have a great practical significance in Civil Engineering.
1.2.1 Mechanical Properties When forces are applied to a solid body, two results are produced:
1) Internal resisting forces
2) Deformation .
The internal forces and deformations are called stresses and strains respectively.
Depending up on the arrangement and direction of the external forces, the stress produced may be:
a) Tensile stress
b) Compressive stress
c) Shearing stress
d) Bending stress
e) Torsional stress
f) Combinations of the above stresses
Deformation:
a) Elastic if it recovers when the external force is released
b) Plastic if it fails to recover when the external force is released If a material is capable to carry its own weight and any applied load, it is assumed to be strong material.
This way is that the strength of the material is determined. When a material is said to be strong it is its strength in tension or compression that is usually referred to, but it is often necessary to know its strength in shear and torsion as well.
1.3 Tests for Mechanical Properties Selection of material for a particular structural application depends on its mechanical properties.
There are standard mechanical tests to measure these properties. Mechanical tests are used to examine the performance of materials under the action of external force.
1.3.1 Classification of Mechanical Tests
I) II) With reference to the direction of the external
forces
a) Tension test
b) Compression test
c) Shear test
d) Bending test
e) Torsion test
With reference to the rate and duration of the load application
a) Static Tests: these are made with gradually
increasing load, such as ordinary tests in tension,
compression etc.
b) Dynamic test: these are made with suddenly
applied loads, as by falling weight
c) Wear tests: these are made to determine
resistance to abrasion and impact, as in the case of
paving materials
d) Longtime tests: there are made with loads
applied to the object under test for a long period of
time. They are used for materials such as concrete.
e) Fatigue test: these are made with fluctuating
stresses repeated a large number of times
III) With reference to the effect of the test on the
specimen
a) Destructive tests: Under these test methods, the
specimens are either crushed or ruptured and made useless at the end of the tests
b) Non-destructive tests: These are usually used to
test the strength of members of existing structures without affecting their performance.
.
➡Join for more updates via the link below;
t.me/COTMp
👆👆👆👆👆
⚡ አሁኑኑ Join በማረግ እና ለጓደኛዎ እና ለሚያቁት ሁሉ ሼር ያድርጉ።
.
1.1 Classification of Construction Materials
Construction materials can be classified into:
I) Metallic and Non-metallic
a. Non-metallic
- Cementing materials
- Concrete
- Timber
- Stone
- Plastics
- Ceramics
b. Metallic
- Ferrous
• Wrought iron
• Cast iron
• Steel
- Non Ferrous
• Aluminium
• Copper
• Lead
• Zinc
II) Based on their physical Nature:
a) Solid
b) Liquid
c) Gaseous
III) Based on their mode of manufacture
a) Naturally occurring materials
b) Industrially produced materials
c) Materials produced at construction site
1.2 Properties of Materials
a) Physical properties
• Density and specific gravity
•Mechanical properties
• Thermal properties
• Acoustical properties
b) Chemical properties
• Corrosion Here only the mechanical properties are dealt with since they have a great practical significance in Civil Engineering.
1.2.1 Mechanical Properties When forces are applied to a solid body, two results are produced:
1) Internal resisting forces
2) Deformation .
The internal forces and deformations are called stresses and strains respectively.
Depending up on the arrangement and direction of the external forces, the stress produced may be:
a) Tensile stress
b) Compressive stress
c) Shearing stress
d) Bending stress
e) Torsional stress
f) Combinations of the above stresses
Deformation:
a) Elastic if it recovers when the external force is released
b) Plastic if it fails to recover when the external force is released If a material is capable to carry its own weight and any applied load, it is assumed to be strong material.
This way is that the strength of the material is determined. When a material is said to be strong it is its strength in tension or compression that is usually referred to, but it is often necessary to know its strength in shear and torsion as well.
1.3 Tests for Mechanical Properties Selection of material for a particular structural application depends on its mechanical properties.
There are standard mechanical tests to measure these properties. Mechanical tests are used to examine the performance of materials under the action of external force.
1.3.1 Classification of Mechanical Tests
I) II) With reference to the direction of the external
forces
a) Tension test
b) Compression test
c) Shear test
d) Bending test
e) Torsion test
With reference to the rate and duration of the load application
a) Static Tests: these are made with gradually
increasing load, such as ordinary tests in tension,
compression etc.
b) Dynamic test: these are made with suddenly
applied loads, as by falling weight
c) Wear tests: these are made to determine
resistance to abrasion and impact, as in the case of
paving materials
d) Longtime tests: there are made with loads
applied to the object under test for a long period of
time. They are used for materials such as concrete.
e) Fatigue test: these are made with fluctuating
stresses repeated a large number of times
III) With reference to the effect of the test on the
specimen
a) Destructive tests: Under these test methods, the
specimens are either crushed or ruptured and made useless at the end of the tests
b) Non-destructive tests: These are usually used to
test the strength of members of existing structures without affecting their performance.
.
➡Join for more updates via the link below;
t.me/COTMp
👆👆👆👆👆
⚡ አሁኑኑ Join በማረግ እና ለጓደኛዎ እና ለሚያቁት ሁሉ ሼር ያድርጉ።
Telegram
ETCONp Discussion
📩ለማነኛውም ሀሳብ እና አስተያየት @Philemona7
✌️ይህ የ @etconp መወያያ ግሩፓቹ ነው።
✋This is discussion group of @ETCONpWORK
.
🔖ማሳሰብያ ...
.
⚡️ግሩፑ ላይ ማነኛውም ከ ኮንስትራክሽን ጉዳዮች ውጪ መለጠፍ በፍፁም አይፈቀድም!
@ETCONpBOT ፃፉልን እናመሰግናለን🙏
✌️ይህ የ @etconp መወያያ ግሩፓቹ ነው።
✋This is discussion group of @ETCONpWORK
.
🔖ማሳሰብያ ...
.
⚡️ግሩፑ ላይ ማነኛውም ከ ኮንስትራክሽን ጉዳዮች ውጪ መለጠፍ በፍፁም አይፈቀድም!
@ETCONpBOT ፃፉልን እናመሰግናለን🙏
❤1
🚩Lets Safe Construction @COTMp
.
👉A safe practice for formwork during construction at site is important for safety of workmen.
improper erection of formwork can cause damage to structural l element as well as pose threat to the safety of workmen.
▶Following are the safe practices checklist for
formwork:👇
1. Formwork should be properly designed for the
structural element considered and its working
drawing should be available at site.
2. Design of formwork should consider all the loads it will experience during casting of concrete
structural members.
3. Strength of materials used for formwork should
be adequate to support structural load as well as
other loads imposed on it.
4. Formwork design should indicate the rate of
concrete pour, height of concrete pour, temperature
and sequence and schedule of concrete pours.
5. Working drawing of formwork should have
detailed dimensions including pouring pocket size, compaction opening and clean outs.
6. Formwork design should consider the safe
bearing capacity of soil.
Formwork Safety Checklist during Construction:
▶Following inspection should be carried out before starting the concreting of structural member:
1. Inspection of entire formwork system for details from bottom to top of formwork for proper load transfer in safe manner.
2. Inspection of working scaffolds, ladders, runways, ramps and crossings.
3. Maintenance of good housekeeping around
working area and passage.
4. Guarding of peripheral edges and floor openings.
5. Adequate space for safe working.
6. Safety training of workmen involved in formwork and concreting works.
7. Use of all personal protective equipment (PPEs).
8. Formwork, rigging inserts and connections checked for correct installation and periodically checked for wear and correct position.
9. Removal of all unused and hanging forms, loose
materials etc. stored on exposed floors.
10. Inspection of all props and shores for adequacy
to handle all the loads.
11. Removal of defective props.
12. Alignment of props such as verticality, height
and spacing between props should be inspected.
13. All props should be rested on bearing plates.
14. Props should be placed on hard bearing
surface.
15. Safe nailing and firm locking of clamps on
adjustable props.
16. Lateral stability of formwork and complete fixity at the joint between props when one prop is placed on the top of the other.
17. Proper bearing below the stringers and joists at
points of supports.
18. De-shuttering and removal of props below
concrete slabs and beams after development of
adequate strength in concrete.
19. Construction loads not placed on freshly cast
slab or beams while removal of formwork or before concrete attaining required strength.
.
⚡ አሁኑኑ Join በማረግ እና ለጓደኛዎ እና ለሚያቁት ሁሉ ሼር ያድርጉ።
.
👉A safe practice for formwork during construction at site is important for safety of workmen.
improper erection of formwork can cause damage to structural l element as well as pose threat to the safety of workmen.
▶Following are the safe practices checklist for
formwork:👇
1. Formwork should be properly designed for the
structural element considered and its working
drawing should be available at site.
2. Design of formwork should consider all the loads it will experience during casting of concrete
structural members.
3. Strength of materials used for formwork should
be adequate to support structural load as well as
other loads imposed on it.
4. Formwork design should indicate the rate of
concrete pour, height of concrete pour, temperature
and sequence and schedule of concrete pours.
5. Working drawing of formwork should have
detailed dimensions including pouring pocket size, compaction opening and clean outs.
6. Formwork design should consider the safe
bearing capacity of soil.
Formwork Safety Checklist during Construction:
▶Following inspection should be carried out before starting the concreting of structural member:
1. Inspection of entire formwork system for details from bottom to top of formwork for proper load transfer in safe manner.
2. Inspection of working scaffolds, ladders, runways, ramps and crossings.
3. Maintenance of good housekeeping around
working area and passage.
4. Guarding of peripheral edges and floor openings.
5. Adequate space for safe working.
6. Safety training of workmen involved in formwork and concreting works.
7. Use of all personal protective equipment (PPEs).
8. Formwork, rigging inserts and connections checked for correct installation and periodically checked for wear and correct position.
9. Removal of all unused and hanging forms, loose
materials etc. stored on exposed floors.
10. Inspection of all props and shores for adequacy
to handle all the loads.
11. Removal of defective props.
12. Alignment of props such as verticality, height
and spacing between props should be inspected.
13. All props should be rested on bearing plates.
14. Props should be placed on hard bearing
surface.
15. Safe nailing and firm locking of clamps on
adjustable props.
16. Lateral stability of formwork and complete fixity at the joint between props when one prop is placed on the top of the other.
17. Proper bearing below the stringers and joists at
points of supports.
18. De-shuttering and removal of props below
concrete slabs and beams after development of
adequate strength in concrete.
19. Construction loads not placed on freshly cast
slab or beams while removal of formwork or before concrete attaining required strength.
.
⚡ አሁኑኑ Join በማረግ እና ለጓደኛዎ እና ለሚያቁት ሁሉ ሼር ያድርጉ።
👍1
👉BASIC THINGS YOU MUST KNOW AS A CONSTRUCTION ENGINEER @COTMp
:
▶Minimum slab thickness is 125mm, but it is advisable to stick to 150mm
▶Always ensure a tolerance of 2mm when casting cubes
▶Minimum number of reinforcements in a square
column is 4nos and 6nos for a circular column.
▶Longitudinal reinforcements must not be less than 0.8% and more than 6% of the gross concrete section
▶water absorption of bricks must be kept to a
tolerable limit of 15%
▶If bar diameter exceeds 36mm, avoid introducing
lap lengths
▶Minimum bar diameter for slab reinforcements is
8mm for high yield steel or 10mm for mild steel, (It is advisable to stick to 12mm).
▶Distribution bars for slab reinforcements must not
be less than 8mm (it is advisable to stick to
10mm) and must not exceed 1/8 of slab thickness.
▶Maximum free fall of concretes must not exceed
1.50m
▶Compressive strength of concrete bricks is 3.5N mm^2
▶PH value of the water used for construction must
not be less than 6.
➡These are some of the basic things you should
know as an engineer. So go to that site and show
them what you have got because Knowledge is
Power.
.
⚡ አሁኑኑ Join በማረግ እና ለጓደኛዎ እና ለሚያቁት ሁሉ ሼር ያድርጉ።
:
▶Minimum slab thickness is 125mm, but it is advisable to stick to 150mm
▶Always ensure a tolerance of 2mm when casting cubes
▶Minimum number of reinforcements in a square
column is 4nos and 6nos for a circular column.
▶Longitudinal reinforcements must not be less than 0.8% and more than 6% of the gross concrete section
▶water absorption of bricks must be kept to a
tolerable limit of 15%
▶If bar diameter exceeds 36mm, avoid introducing
lap lengths
▶Minimum bar diameter for slab reinforcements is
8mm for high yield steel or 10mm for mild steel, (It is advisable to stick to 12mm).
▶Distribution bars for slab reinforcements must not
be less than 8mm (it is advisable to stick to
10mm) and must not exceed 1/8 of slab thickness.
▶Maximum free fall of concretes must not exceed
1.50m
▶Compressive strength of concrete bricks is 3.5N mm^2
▶PH value of the water used for construction must
not be less than 6.
➡These are some of the basic things you should
know as an engineer. So go to that site and show
them what you have got because Knowledge is
Power.
.
⚡ አሁኑኑ Join በማረግ እና ለጓደኛዎ እና ለሚያቁት ሁሉ ሼር ያድርጉ።
👉HOW TO CHECK QUALITY OF CEMENT AT SITE @COTMp
~~~~~~~~~~~~~~~~
➡Cement is one of the most important materials
used in construction. The strength of a structure
depends upon several factors, cement quality is one of them. To achieve the desired strength of
concrete and to increase the longevity of structure
good quality cement should always be used.
So it is important to check the quality of cement
before using. In our previous article, we have
already discussed the different types of cement and their uses in construction. Today we will discuss how to check the quality of cement at site.
To check the quality of cement we need to pass
some easy tests which are described below.
1. DATE OF PACKING:
The strength of cement decreases with time. First
of all, check the manufacturing date in the bag before using. Generally, cement should be used before 90 days from the manufacturing date.
three months stored cement decreases its strength by 20-30 %, six months stored cement decreases its strength by 30-40% and 12 months stored cement decrease its strength by 40-50%
2. CEMENT COLOR:
The cement should be uniform in color. Good
quality cement should have gray color with greenish shade.
3. CHECK FOR LUMPS:
No lumps should be present in the cement. Lumps are formed due to absorption of moisture from the climate.
4. RUBBING TEST:
Cement should feel smooth while rubbing in
between fingers. If it gives a rough feeling that
means cement is mixed with sand.
5 TEMPERATURE TEST:
Simply insert your hand into the cement bag, it should give cool feeling if its quality is good.
Otherwise, you may feel warm because of hydration reaction.
6. FLOAT TEST:
Take some amount of cement and throw it in water.
The cement should float for sometimes before it sinks in the water.
7. SETTING TEST:
Make a thick cement paste with water and immerse it in water for 24 hours.
It should be set and should not develop cracks.
8. STRENGTH TEST:
Prepare a cement block of 25 mm x 25 mm and 200 mm in length.
Now submerge it in water for 7 days. Now place it on supports 15 cm apart and load it with 34 kg weight. Block made from good cement will not show any signs of failure.
~~~~~~~~~~~~~~~~
➡Cement is one of the most important materials
used in construction. The strength of a structure
depends upon several factors, cement quality is one of them. To achieve the desired strength of
concrete and to increase the longevity of structure
good quality cement should always be used.
So it is important to check the quality of cement
before using. In our previous article, we have
already discussed the different types of cement and their uses in construction. Today we will discuss how to check the quality of cement at site.
To check the quality of cement we need to pass
some easy tests which are described below.
1. DATE OF PACKING:
The strength of cement decreases with time. First
of all, check the manufacturing date in the bag before using. Generally, cement should be used before 90 days from the manufacturing date.
three months stored cement decreases its strength by 20-30 %, six months stored cement decreases its strength by 30-40% and 12 months stored cement decrease its strength by 40-50%
2. CEMENT COLOR:
The cement should be uniform in color. Good
quality cement should have gray color with greenish shade.
3. CHECK FOR LUMPS:
No lumps should be present in the cement. Lumps are formed due to absorption of moisture from the climate.
4. RUBBING TEST:
Cement should feel smooth while rubbing in
between fingers. If it gives a rough feeling that
means cement is mixed with sand.
5 TEMPERATURE TEST:
Simply insert your hand into the cement bag, it should give cool feeling if its quality is good.
Otherwise, you may feel warm because of hydration reaction.
6. FLOAT TEST:
Take some amount of cement and throw it in water.
The cement should float for sometimes before it sinks in the water.
7. SETTING TEST:
Make a thick cement paste with water and immerse it in water for 24 hours.
It should be set and should not develop cracks.
8. STRENGTH TEST:
Prepare a cement block of 25 mm x 25 mm and 200 mm in length.
Now submerge it in water for 7 days. Now place it on supports 15 cm apart and load it with 34 kg weight. Block made from good cement will not show any signs of failure.
👍2
👉HOW TO CHECK SAND QUALITY IN FIELD? @COTMp
.
➡There are some useful tests that can be done in the field for checking
the quality of sand utilized for construction. The
following tests may
be performed to determine the characteristics of
sand.
🚩FIELD TEST OF SAND:
1. Take a glass and add some water in it.
2. Add a few amount of sand in the glass. At that
point, shake it vivaciously and permit it to settle. If there is clay present in the sand, an apparent layer will be formed at the top level of sand.
3. Mix the sand into sodium hydroxide or caustic soda solution to
distinguish the presence of organic impurities.
If organic impurities
are present in the sand, the color of the solution
will be turned into brown.
4. Now take a squeeze of sand and taste it. If it is
salty that means salt is present in the sand.
5. Take little amount of sand in the hand, and then
rub it against the
fingers. If the fingers are recolored it means sand
consists of some
earthy materials.
6. The color of sand describes the cleanness of
sand. The size and sharpness might be examined by touching and
watching visually.
7. The sand may be examined by mechanical
analysis to know its
fineness, durability, void ratio etc.
.
➡There are some useful tests that can be done in the field for checking
the quality of sand utilized for construction. The
following tests may
be performed to determine the characteristics of
sand.
🚩FIELD TEST OF SAND:
1. Take a glass and add some water in it.
2. Add a few amount of sand in the glass. At that
point, shake it vivaciously and permit it to settle. If there is clay present in the sand, an apparent layer will be formed at the top level of sand.
3. Mix the sand into sodium hydroxide or caustic soda solution to
distinguish the presence of organic impurities.
If organic impurities
are present in the sand, the color of the solution
will be turned into brown.
4. Now take a squeeze of sand and taste it. If it is
salty that means salt is present in the sand.
5. Take little amount of sand in the hand, and then
rub it against the
fingers. If the fingers are recolored it means sand
consists of some
earthy materials.
6. The color of sand describes the cleanness of
sand. The size and sharpness might be examined by touching and
watching visually.
7. The sand may be examined by mechanical
analysis to know its
fineness, durability, void ratio etc.
Ethio Construction Engineering
Video
#revit#rendering