👉HOW TO CHECK QUALITY OF CEMENT AT SITE @COTMp
~~~~~~~~~~~~~~~~
➡Cement is one of the most important materials
used in construction. The strength of a structure
depends upon several factors, cement quality is one of them. To achieve the desired strength of
concrete and to increase the longevity of structure
good quality cement should always be used.
So it is important to check the quality of cement
before using. In our previous article, we have
already discussed the different types of cement and their uses in construction. Today we will discuss how to check the quality of cement at site.
To check the quality of cement we need to pass
some easy tests which are described below.
1. DATE OF PACKING:
The strength of cement decreases with time. First
of all, check the manufacturing date in the bag before using. Generally, cement should be used before 90 days from the manufacturing date.
three months stored cement decreases its strength by 20-30 %, six months stored cement decreases its strength by 30-40% and 12 months stored cement decrease its strength by 40-50%
2. CEMENT COLOR:
The cement should be uniform in color. Good
quality cement should have gray color with greenish shade.
3. CHECK FOR LUMPS:
No lumps should be present in the cement. Lumps are formed due to absorption of moisture from the climate.
4. RUBBING TEST:
Cement should feel smooth while rubbing in
between fingers. If it gives a rough feeling that
means cement is mixed with sand.
5 TEMPERATURE TEST:
Simply insert your hand into the cement bag, it should give cool feeling if its quality is good.
Otherwise, you may feel warm because of hydration reaction.
6. FLOAT TEST:
Take some amount of cement and throw it in water.
The cement should float for sometimes before it sinks in the water.
7. SETTING TEST:
Make a thick cement paste with water and immerse it in water for 24 hours.
It should be set and should not develop cracks.
8. STRENGTH TEST:
Prepare a cement block of 25 mm x 25 mm and 200 mm in length.
Now submerge it in water for 7 days. Now place it on supports 15 cm apart and load it with 34 kg weight. Block made from good cement will not show any signs of failure.
~~~~~~~~~~~~~~~~
➡Cement is one of the most important materials
used in construction. The strength of a structure
depends upon several factors, cement quality is one of them. To achieve the desired strength of
concrete and to increase the longevity of structure
good quality cement should always be used.
So it is important to check the quality of cement
before using. In our previous article, we have
already discussed the different types of cement and their uses in construction. Today we will discuss how to check the quality of cement at site.
To check the quality of cement we need to pass
some easy tests which are described below.
1. DATE OF PACKING:
The strength of cement decreases with time. First
of all, check the manufacturing date in the bag before using. Generally, cement should be used before 90 days from the manufacturing date.
three months stored cement decreases its strength by 20-30 %, six months stored cement decreases its strength by 30-40% and 12 months stored cement decrease its strength by 40-50%
2. CEMENT COLOR:
The cement should be uniform in color. Good
quality cement should have gray color with greenish shade.
3. CHECK FOR LUMPS:
No lumps should be present in the cement. Lumps are formed due to absorption of moisture from the climate.
4. RUBBING TEST:
Cement should feel smooth while rubbing in
between fingers. If it gives a rough feeling that
means cement is mixed with sand.
5 TEMPERATURE TEST:
Simply insert your hand into the cement bag, it should give cool feeling if its quality is good.
Otherwise, you may feel warm because of hydration reaction.
6. FLOAT TEST:
Take some amount of cement and throw it in water.
The cement should float for sometimes before it sinks in the water.
7. SETTING TEST:
Make a thick cement paste with water and immerse it in water for 24 hours.
It should be set and should not develop cracks.
8. STRENGTH TEST:
Prepare a cement block of 25 mm x 25 mm and 200 mm in length.
Now submerge it in water for 7 days. Now place it on supports 15 cm apart and load it with 34 kg weight. Block made from good cement will not show any signs of failure.
👍2
👉HOW TO CHECK SAND QUALITY IN FIELD? @COTMp
.
➡There are some useful tests that can be done in the field for checking
the quality of sand utilized for construction. The
following tests may
be performed to determine the characteristics of
sand.
🚩FIELD TEST OF SAND:
1. Take a glass and add some water in it.
2. Add a few amount of sand in the glass. At that
point, shake it vivaciously and permit it to settle. If there is clay present in the sand, an apparent layer will be formed at the top level of sand.
3. Mix the sand into sodium hydroxide or caustic soda solution to
distinguish the presence of organic impurities.
If organic impurities
are present in the sand, the color of the solution
will be turned into brown.
4. Now take a squeeze of sand and taste it. If it is
salty that means salt is present in the sand.
5. Take little amount of sand in the hand, and then
rub it against the
fingers. If the fingers are recolored it means sand
consists of some
earthy materials.
6. The color of sand describes the cleanness of
sand. The size and sharpness might be examined by touching and
watching visually.
7. The sand may be examined by mechanical
analysis to know its
fineness, durability, void ratio etc.
.
➡There are some useful tests that can be done in the field for checking
the quality of sand utilized for construction. The
following tests may
be performed to determine the characteristics of
sand.
🚩FIELD TEST OF SAND:
1. Take a glass and add some water in it.
2. Add a few amount of sand in the glass. At that
point, shake it vivaciously and permit it to settle. If there is clay present in the sand, an apparent layer will be formed at the top level of sand.
3. Mix the sand into sodium hydroxide or caustic soda solution to
distinguish the presence of organic impurities.
If organic impurities
are present in the sand, the color of the solution
will be turned into brown.
4. Now take a squeeze of sand and taste it. If it is
salty that means salt is present in the sand.
5. Take little amount of sand in the hand, and then
rub it against the
fingers. If the fingers are recolored it means sand
consists of some
earthy materials.
6. The color of sand describes the cleanness of
sand. The size and sharpness might be examined by touching and
watching visually.
7. The sand may be examined by mechanical
analysis to know its
fineness, durability, void ratio etc.
Ethio Construction Engineering
Video
#revit#rendering
👉PROPERTIES OF HARDENED CONCRETE @COTMp
.
⏩The following are the properties of concrete in its hardened state, used by the designer during design process of reinforced concrete structure.
1. COMPRESSIVE STRENGTH
*The characteristics strength is defined as
the strength of concrete below which not
more than 5% of the test results are expected to fall. As per IS: 456 concrete
mix always designed for the target strength computed as,
Target strength: Characteristics strength + (1.65 x standard deviation) M20 is the minimum grade of concrete for use in RCC work.
2. TENSILE STRENGTH
*Flexural strength is one measure of the Tensile strength of concrete. In concrete structure one set of visible cracks occur under flexure to compute load factor against cracking .According to IS: 456 the tensile strength of concrete can be computed from the compressive strength using empirical relation given by:
Flexural strength:
f =0.7√fck N/mm
3. MODULUS ELASTICITY
*Modulus of elasticity of concrete which is
significantly influenced by the following
factors.
*Type of the aggregates used, Type of cement and
Mix proportions This property is required for the
computations of deflections of structural
concrete members which forms an important limit state in the design of
concrete members. In the absence of test data, the modulus of elasticity of concrete is normally related to the compressive
strength and is computed by the empirical
relationship recommended by IS: 456-2000
code and is expressed as,
E =5000√fck
*Where E is the short term static modulus of elasticity of concrete expressed in N/mm f is the characteristic compressive
strength of concrete expressed in N/mm .
4. SHRINKAGE OF CONCRETE
*The ingredients of concrete and environmental conditions like temperature and humidity influence the total shrinkage of concrete. Water content in concrete significantly affects the shrinkage. The IS: 456-2000 recommends the total shrinkage
strain as 0.0003 in the absence of test data. Drying shrinkage in plain concrete may result in surface cracks. Shrinkage of concrete also influences the deflections of reinforced concrete members.
5. CREEP OF CONCRETE
*The inelastic time dependent strain
developed in a concrete ember under sustained loading is referred to as creep of concrete. Creep of concrete is influenced
by following factors.
Cement content,
W/C ratio, Temperature and humidity, Size of structural element,
*Type of loading and period of loading. In the absence of reliable experimental data, the creep coefficient is expressed as the ratio of ultimate creep strain/elastic strain at various ages of loading as recommended by IS: 456-2000 are given
below.
*Age at Loading Creep Coefficient
7 days 2.2
28 days 1.6
1 year 1.1
*Creep of concrete significantly affects the deflections of reinforced concrete flexural
members. Higher creep coefficient results
in large deflections. The value of creep coefficient is useful in the computation of time dependent deflections in reinforced concrete members.
6. COEFFICIENT OF THERMAL EXPANSION
*The coefficient of thermal expansion of concrete, influenced mainly by the type of aggregate used in concrete is required for
the design of structures like chimneys, water tanks, silos etc.
.
👇👇👇👇👇
Join for more updates via the link below;
t.me/COTMp
👆👆👆👆👆
⚡ አሁኑኑ Join በማረግ እና ለጓደኛዎ እና ለሚያቁት ሁሉ ሼር ያድርጉ።
.
⏩The following are the properties of concrete in its hardened state, used by the designer during design process of reinforced concrete structure.
1. COMPRESSIVE STRENGTH
*The characteristics strength is defined as
the strength of concrete below which not
more than 5% of the test results are expected to fall. As per IS: 456 concrete
mix always designed for the target strength computed as,
Target strength: Characteristics strength + (1.65 x standard deviation) M20 is the minimum grade of concrete for use in RCC work.
2. TENSILE STRENGTH
*Flexural strength is one measure of the Tensile strength of concrete. In concrete structure one set of visible cracks occur under flexure to compute load factor against cracking .According to IS: 456 the tensile strength of concrete can be computed from the compressive strength using empirical relation given by:
Flexural strength:
f =0.7√fck N/mm
3. MODULUS ELASTICITY
*Modulus of elasticity of concrete which is
significantly influenced by the following
factors.
*Type of the aggregates used, Type of cement and
Mix proportions This property is required for the
computations of deflections of structural
concrete members which forms an important limit state in the design of
concrete members. In the absence of test data, the modulus of elasticity of concrete is normally related to the compressive
strength and is computed by the empirical
relationship recommended by IS: 456-2000
code and is expressed as,
E =5000√fck
*Where E is the short term static modulus of elasticity of concrete expressed in N/mm f is the characteristic compressive
strength of concrete expressed in N/mm .
4. SHRINKAGE OF CONCRETE
*The ingredients of concrete and environmental conditions like temperature and humidity influence the total shrinkage of concrete. Water content in concrete significantly affects the shrinkage. The IS: 456-2000 recommends the total shrinkage
strain as 0.0003 in the absence of test data. Drying shrinkage in plain concrete may result in surface cracks. Shrinkage of concrete also influences the deflections of reinforced concrete members.
5. CREEP OF CONCRETE
*The inelastic time dependent strain
developed in a concrete ember under sustained loading is referred to as creep of concrete. Creep of concrete is influenced
by following factors.
Cement content,
W/C ratio, Temperature and humidity, Size of structural element,
*Type of loading and period of loading. In the absence of reliable experimental data, the creep coefficient is expressed as the ratio of ultimate creep strain/elastic strain at various ages of loading as recommended by IS: 456-2000 are given
below.
*Age at Loading Creep Coefficient
7 days 2.2
28 days 1.6
1 year 1.1
*Creep of concrete significantly affects the deflections of reinforced concrete flexural
members. Higher creep coefficient results
in large deflections. The value of creep coefficient is useful in the computation of time dependent deflections in reinforced concrete members.
6. COEFFICIENT OF THERMAL EXPANSION
*The coefficient of thermal expansion of concrete, influenced mainly by the type of aggregate used in concrete is required for
the design of structures like chimneys, water tanks, silos etc.
.
👇👇👇👇👇
Join for more updates via the link below;
t.me/COTMp
👆👆👆👆👆
⚡ አሁኑኑ Join በማረግ እና ለጓደኛዎ እና ለሚያቁት ሁሉ ሼር ያድርጉ።
Telegram
ETCONp Discussion
📩ለማነኛውም ሀሳብ እና አስተያየት @Philemona7
✌️ይህ የ @etconp መወያያ ግሩፓቹ ነው።
✋This is discussion group of @ETCONpWORK
.
🔖ማሳሰብያ ...
.
⚡️ግሩፑ ላይ ማነኛውም ከ ኮንስትራክሽን ጉዳዮች ውጪ መለጠፍ በፍፁም አይፈቀድም!
@ETCONpBOT ፃፉልን እናመሰግናለን🙏
✌️ይህ የ @etconp መወያያ ግሩፓቹ ነው።
✋This is discussion group of @ETCONpWORK
.
🔖ማሳሰብያ ...
.
⚡️ግሩፑ ላይ ማነኛውም ከ ኮንስትራክሽን ጉዳዮች ውጪ መለጠፍ በፍፁም አይፈቀድም!
@ETCONpBOT ፃፉልን እናመሰግናለን🙏
❤1👍1
👉 የአፈርን የመሸከም አቅም (BEARING CAPACITY) እንዴት እንጨምር??...
.
* ሶስት አይነት የአፈርን የመሸከም አቅም ማስተካከያ ቴክኒኮች አሉ - mechanical, chemical & other stabilization techniques
.
A) ሜካኒካል ውስጥ :-
.
1. Compaction - አፈሩን ስንጠቀጥቀው density/ unit
weight ይጨምራል ያ ማለት ደግሞ አፈርን የመሸከም አቅም ጨመረ ማለት ነው::
.
2. Excavation and Replacement – expansive soil ከሆነ ወይም ሌላ አስቸጋሪ አፈር ከሆነ ይህን መጠቀም እንችላለን
.
3. Mixing of Different Soils - ሳይታችን ላይ ያለው አፈር
coarse ወይም fine ብቻ ከሆነ ወይም ደግሞ አፈሩ አንድ አይነት
ብቻ ፀባይ ካለው ከተለያዩ አፈሮች ጋር በመደባለቅ የተሻለ የአፈር
ፀባይ ማግኘት እንችላለን
.
B) ኬሚካል :-
.
1. Lime stabilization - ይህንን የምንጠቀመው በአብዛኛው
ለexpansive soil ነው፡፡ አፈሩን ከ Lime ጋር በመደባለቅ
plasticity መቀነስ እንችላለን፡፡ የlime መጠኑ ከሚያስፈልገው
በላይ ከበዛ ግን B.C. ይቀንሳል፡፡
.
2. Cement stabilization - ሲሚንቶን ከአፈር ጋር በመደባለቅ
የተሻለ ውጤትን የምናገኝበት መንገድ ነው፡፡ concrete
pavement ስር መጠቀም እንችላለን በአብዛኛው ለአየር
መንገዶች ፤ ለአውራ ጎዳናዎች ፤ ግድቦችን ከሽርሸራ ለመከላከል
ወ.ዘ.ተ. መጠቀም እንችላለን፡፡
.
3. Asphalt stabilization - አስፓልትን ከአፈር ጋር በመደባለቅ
የተሻለ ውጤትን የምናገኝበት ዘዴ ነው በተለይም ለcohesive
አፈሮች፡፡ አፈሩን water proof በማድረግና ውሃማነትን በመቀነስ
B. Cን መጨመር እንችላለን፡፡ በአብዛኛው ይህንን ድብልቅ
ለመንገዶች እንደ base course መጠቀም እንችላለን፡፡
.
.
C) ሌሎች የአፈርን ባህሪ ማስተካከያ መንገዶች:-
.
1. Drainage - ፓይፖችን አፈር ውስጥ በመቅበር ወይም
ጉድጓዶችን በመጠቀም ground water የምንቆጣጠርበት ነው
.
2. Precompression - ግንባታ ከመጀመራችን በፊት አፈሩ ላይ
ሎድ በመጫን ኮምፓክት የምናደርግበት ዘዴ ነው
.
3. Dynamic Stabilization
.
ሀ) Blasting - ቦምብ ወደውስጥ በመቅበር በፍንዳታው አፈሩ ይጠቀጠቃል::
.
ለ) Compaction Piles - ፓይሎችን ወደውስጥ በማስገባት
አፈሩ ወደ ጎን እንዲሸሽና እንዲጠቀጠቅ ማድረግ ይቻላል፡፡
ፓይሉን ስናስወጣውም በተቦረቦረው ጉድጓድ ውስጥ የተሻለ አፈር በማስገባት የአፈርን የመሸከም አቅም ማስተካከል እንችላለን፡፡
.
4. Injection And Grouting - አፈሩን በሲሚንቶ ወይም
በተለያዩ chemical ውህዶች በpressure በመምታት ground
water ና settlement መቆጣጠር እንችላለን፡፡
.
የተሻለውን ዘዴ ለመምረጥ የአፈሩንና የአካባቢውን ሁኔታ ፤
ኢኮኖሚ ፤ ሴፍቲና የመሳሰሉትን ነገሮች ማጤን አለብን፡፡
.
👉FOR MORE UPDATED CONSTRUCTION INFO JOIN US HERE 👇
http://t.me/COTMp
.
* ሶስት አይነት የአፈርን የመሸከም አቅም ማስተካከያ ቴክኒኮች አሉ - mechanical, chemical & other stabilization techniques
.
A) ሜካኒካል ውስጥ :-
.
1. Compaction - አፈሩን ስንጠቀጥቀው density/ unit
weight ይጨምራል ያ ማለት ደግሞ አፈርን የመሸከም አቅም ጨመረ ማለት ነው::
.
2. Excavation and Replacement – expansive soil ከሆነ ወይም ሌላ አስቸጋሪ አፈር ከሆነ ይህን መጠቀም እንችላለን
.
3. Mixing of Different Soils - ሳይታችን ላይ ያለው አፈር
coarse ወይም fine ብቻ ከሆነ ወይም ደግሞ አፈሩ አንድ አይነት
ብቻ ፀባይ ካለው ከተለያዩ አፈሮች ጋር በመደባለቅ የተሻለ የአፈር
ፀባይ ማግኘት እንችላለን
.
B) ኬሚካል :-
.
1. Lime stabilization - ይህንን የምንጠቀመው በአብዛኛው
ለexpansive soil ነው፡፡ አፈሩን ከ Lime ጋር በመደባለቅ
plasticity መቀነስ እንችላለን፡፡ የlime መጠኑ ከሚያስፈልገው
በላይ ከበዛ ግን B.C. ይቀንሳል፡፡
.
2. Cement stabilization - ሲሚንቶን ከአፈር ጋር በመደባለቅ
የተሻለ ውጤትን የምናገኝበት መንገድ ነው፡፡ concrete
pavement ስር መጠቀም እንችላለን በአብዛኛው ለአየር
መንገዶች ፤ ለአውራ ጎዳናዎች ፤ ግድቦችን ከሽርሸራ ለመከላከል
ወ.ዘ.ተ. መጠቀም እንችላለን፡፡
.
3. Asphalt stabilization - አስፓልትን ከአፈር ጋር በመደባለቅ
የተሻለ ውጤትን የምናገኝበት ዘዴ ነው በተለይም ለcohesive
አፈሮች፡፡ አፈሩን water proof በማድረግና ውሃማነትን በመቀነስ
B. Cን መጨመር እንችላለን፡፡ በአብዛኛው ይህንን ድብልቅ
ለመንገዶች እንደ base course መጠቀም እንችላለን፡፡
.
.
C) ሌሎች የአፈርን ባህሪ ማስተካከያ መንገዶች:-
.
1. Drainage - ፓይፖችን አፈር ውስጥ በመቅበር ወይም
ጉድጓዶችን በመጠቀም ground water የምንቆጣጠርበት ነው
.
2. Precompression - ግንባታ ከመጀመራችን በፊት አፈሩ ላይ
ሎድ በመጫን ኮምፓክት የምናደርግበት ዘዴ ነው
.
3. Dynamic Stabilization
.
ሀ) Blasting - ቦምብ ወደውስጥ በመቅበር በፍንዳታው አፈሩ ይጠቀጠቃል::
.
ለ) Compaction Piles - ፓይሎችን ወደውስጥ በማስገባት
አፈሩ ወደ ጎን እንዲሸሽና እንዲጠቀጠቅ ማድረግ ይቻላል፡፡
ፓይሉን ስናስወጣውም በተቦረቦረው ጉድጓድ ውስጥ የተሻለ አፈር በማስገባት የአፈርን የመሸከም አቅም ማስተካከል እንችላለን፡፡
.
4. Injection And Grouting - አፈሩን በሲሚንቶ ወይም
በተለያዩ chemical ውህዶች በpressure በመምታት ground
water ና settlement መቆጣጠር እንችላለን፡፡
.
የተሻለውን ዘዴ ለመምረጥ የአፈሩንና የአካባቢውን ሁኔታ ፤
ኢኮኖሚ ፤ ሴፍቲና የመሳሰሉትን ነገሮች ማጤን አለብን፡፡
.
👉FOR MORE UPDATED CONSTRUCTION INFO JOIN US HERE 👇
http://t.me/COTMp
Telegram
ETCONp Discussion
📩ለማነኛውም ሀሳብ እና አስተያየት @Philemona7
✌️ይህ የ @etconp መወያያ ግሩፓቹ ነው።
✋This is discussion group of @ETCONpWORK
.
🔖ማሳሰብያ ...
.
⚡️ግሩፑ ላይ ማነኛውም ከ ኮንስትራክሽን ጉዳዮች ውጪ መለጠፍ በፍፁም አይፈቀድም!
@ETCONpBOT ፃፉልን እናመሰግናለን🙏
✌️ይህ የ @etconp መወያያ ግሩፓቹ ነው።
✋This is discussion group of @ETCONpWORK
.
🔖ማሳሰብያ ...
.
⚡️ግሩፑ ላይ ማነኛውም ከ ኮንስትራክሽን ጉዳዮች ውጪ መለጠፍ በፍፁም አይፈቀድም!
@ETCONpBOT ፃፉልን እናመሰግናለን🙏
በበጀት ዓመቱ በመንግስት ግንባታዎች ላይ ለዜጎች የስራ ዕድል እና የገበያ ትስስር እንደሚፈጠር ተገለፀ፡፡
በተያዘው በጀት ዓመት ለ 2000 ኮንትራክተሮችና ለ 2000 አማካሪ ድርጅቶች በመንግሥት ግንባታዎች ላይ በቋሚነትና በጊዜያዊነት ቅጥር ለመፈፀም እንደታሰበ ተገልፇል፡፡
በተጨማሪም 16,000 የግንባታ ባለሞያዎችን በመመዝገብ በግንባታ ሳይቶች ላይ በጊዜያዊነትና በቋሚነት እንዲሰሩ ይደረጋል የተባለ ሲሆን በሚፈጠሩት የስራ ዕድሎችም የ 1 ቢሊዮን ብር የገበያ ትስስር ለመፍጠር ማቀዱን የቢሮው የ 2012 ዕቅድ ያመለክታል፡፡
አ/አ/ከ/አ/ኮንስትራክሽን ቢሮ (መስከረም 6/2012 ዓ/ም
Share @cotmp
በተያዘው በጀት ዓመት ለ 2000 ኮንትራክተሮችና ለ 2000 አማካሪ ድርጅቶች በመንግሥት ግንባታዎች ላይ በቋሚነትና በጊዜያዊነት ቅጥር ለመፈፀም እንደታሰበ ተገልፇል፡፡
በተጨማሪም 16,000 የግንባታ ባለሞያዎችን በመመዝገብ በግንባታ ሳይቶች ላይ በጊዜያዊነትና በቋሚነት እንዲሰሩ ይደረጋል የተባለ ሲሆን በሚፈጠሩት የስራ ዕድሎችም የ 1 ቢሊዮን ብር የገበያ ትስስር ለመፍጠር ማቀዱን የቢሮው የ 2012 ዕቅድ ያመለክታል፡፡
አ/አ/ከ/አ/ኮንስትራክሽን ቢሮ (መስከረም 6/2012 ዓ/ም
Share @cotmp
👉COMMON CONCRETE PROBLEMS AND THEIR
PREVENTION @COTMp
.
⏩There are many problems we might be facing during and after concreting.
*To produce high quality
concrete we must take some precautions to avoid
those common problems during concreting. In this
article, we will discuss on common concrete
problems and how to prevent them.
A) BLEEDING:
Bleeding refers to as a tendency of water to appear on the top surface of concrete after finishing. Due to bleeding some measure of water (with sand particles and other cementing materials) appears at the surface of the concrete.
*Following precautions should be taken to reduce
bleeding in concrete.
1. Design the mix appropriately.
2. Include least water content in the mix.
3. Use greater amount of cement content.
4. Use greater amount of fine particles.
5. Utilize a little measure of air entraining
admixture.
B) SEGREGATION:
Segregation means separation of coarse aggregates from the concrete surface due to poor compaction.
It is generally seen in the plastic stage of concrete.
As a result honeycomb, laitance, scaling, porous
layer, bond failure etc. can be formed in concrete.
Following precautions should be adopted to prevent segregation in concrete.
1. Design the mix appropriately.
2. Never use excessive water content.
3. Take care of handling, placing, and proper
compaction of concrete.
4. Do not allow the concrete to be dropped from more heights.
5. Use air entraining admixture.
6. Keep the formwork to be watertight.
C) LAITANCE:
The appearance of cement-sand particles on the
surface of freshly placed concrete is known as
laitance. It is mainly occurred due to the bad effect of bleeding and segregation of concrete. The bond between subsequent layers of concrete becomes
weaker and as a result, laitance is developed.
Following precautions can be taken to stop the
occurrence of laitance in concrete.
1. Clay, dust, silt content etc should be removed
before mixing the concrete.
2. Water-cement ratio should be maintained
properly.
3. Water should not be sprayed on the concrete
surface during finishing work.
4. Use well graded fine aggregates in the mix.
5. Add little amount of water reducing admixture in the concrete mix.
D) SCALING:
Scaling is the physical deterioration of concrete in
which the surface layer of concrete broke down,
pitted or flaked away. Due to this effect concrete
surface becomes worse. Scaling can be prevented
by taking same precautions adopted for laitance.
E) PLASTIC SHRINKAGE CRACKS:
When the evaporation rate of water mixed in the
concrete is greater than the bleed water of concrete,
plastic shrinkage cracks are developed on the
surface of the concrete. Basically, this type of
cracks occurs in very hot climate.
F) DUSTING:
Dusting can be prevented by taking following
precautions.
1. Maintain a suitable water/cement ratio in the
concrete.
2. Utilize dust free aggregates in the mix.
3. Guarantee appropriate hydration of concrete.
4. Avoid early surface finishing of concrete.
.
⚡ አሁኑኑ Join በማረግ እና ለጓደኛዎ እና ለሚያቁት ሁሉ ሼር ያድርጉ።
PREVENTION @COTMp
.
⏩There are many problems we might be facing during and after concreting.
*To produce high quality
concrete we must take some precautions to avoid
those common problems during concreting. In this
article, we will discuss on common concrete
problems and how to prevent them.
A) BLEEDING:
Bleeding refers to as a tendency of water to appear on the top surface of concrete after finishing. Due to bleeding some measure of water (with sand particles and other cementing materials) appears at the surface of the concrete.
*Following precautions should be taken to reduce
bleeding in concrete.
1. Design the mix appropriately.
2. Include least water content in the mix.
3. Use greater amount of cement content.
4. Use greater amount of fine particles.
5. Utilize a little measure of air entraining
admixture.
B) SEGREGATION:
Segregation means separation of coarse aggregates from the concrete surface due to poor compaction.
It is generally seen in the plastic stage of concrete.
As a result honeycomb, laitance, scaling, porous
layer, bond failure etc. can be formed in concrete.
Following precautions should be adopted to prevent segregation in concrete.
1. Design the mix appropriately.
2. Never use excessive water content.
3. Take care of handling, placing, and proper
compaction of concrete.
4. Do not allow the concrete to be dropped from more heights.
5. Use air entraining admixture.
6. Keep the formwork to be watertight.
C) LAITANCE:
The appearance of cement-sand particles on the
surface of freshly placed concrete is known as
laitance. It is mainly occurred due to the bad effect of bleeding and segregation of concrete. The bond between subsequent layers of concrete becomes
weaker and as a result, laitance is developed.
Following precautions can be taken to stop the
occurrence of laitance in concrete.
1. Clay, dust, silt content etc should be removed
before mixing the concrete.
2. Water-cement ratio should be maintained
properly.
3. Water should not be sprayed on the concrete
surface during finishing work.
4. Use well graded fine aggregates in the mix.
5. Add little amount of water reducing admixture in the concrete mix.
D) SCALING:
Scaling is the physical deterioration of concrete in
which the surface layer of concrete broke down,
pitted or flaked away. Due to this effect concrete
surface becomes worse. Scaling can be prevented
by taking same precautions adopted for laitance.
E) PLASTIC SHRINKAGE CRACKS:
When the evaporation rate of water mixed in the
concrete is greater than the bleed water of concrete,
plastic shrinkage cracks are developed on the
surface of the concrete. Basically, this type of
cracks occurs in very hot climate.
F) DUSTING:
Dusting can be prevented by taking following
precautions.
1. Maintain a suitable water/cement ratio in the
concrete.
2. Utilize dust free aggregates in the mix.
3. Guarantee appropriate hydration of concrete.
4. Avoid early surface finishing of concrete.
.
⚡ አሁኑኑ Join በማረግ እና ለጓደኛዎ እና ለሚያቁት ሁሉ ሼር ያድርጉ።
❤1
👉ውድ የ @COTMp ተከታዮች እንዴት ናችሁ ዛሬ ደሞ ከታች ያሉ ጥያቄዎች ኣዘጋጅተናል መልሳቹ Discussion ላይ በሚገኝው Group ላይ ኣስቀምጡልን ማለትም በዚህ..
➡ @COTMp ይመልሱ እና እንማማር።
.
⏩try these questions...
.
1. List at least four factors that affect design of
concrete mix?
2. Write procedures of laying of rising main pipes in a water supply project.
3. Estimate the quantities of brickwork and
plastering required in a wall 4 m long, 3 m high
and 30 cm thick.
*Calculate also the cost if the rate of brickwork is
320.00birr per cu m and of plastering is 8.50 birr
per sq m.
4. Given 10m3 Concrete C – 15 Mechanical mixes
with mix ratio 1:2:4. Assuming that 30% shrinkage and 5% wastage and also take density of cement as 1400kg/m3.
Calculate the amount of cement required to make
10m3 of 1:2:4 concrete in kilograms.
*Calculate the volume of sand in cubic meter .
*Calculate the volume of gravel (crushed stone) in
cubic meter.
.
⚡ አሁኑኑ Join በማረግ እና ለጓደኛዎ እና ለሚያቁት ሁሉ ሼር ያድርጉ። እናመሰግናለን😍
➡ @COTMp ይመልሱ እና እንማማር።
.
⏩try these questions...
.
1. List at least four factors that affect design of
concrete mix?
2. Write procedures of laying of rising main pipes in a water supply project.
3. Estimate the quantities of brickwork and
plastering required in a wall 4 m long, 3 m high
and 30 cm thick.
*Calculate also the cost if the rate of brickwork is
320.00birr per cu m and of plastering is 8.50 birr
per sq m.
4. Given 10m3 Concrete C – 15 Mechanical mixes
with mix ratio 1:2:4. Assuming that 30% shrinkage and 5% wastage and also take density of cement as 1400kg/m3.
Calculate the amount of cement required to make
10m3 of 1:2:4 concrete in kilograms.
*Calculate the volume of sand in cubic meter .
*Calculate the volume of gravel (crushed stone) in
cubic meter.
.
⚡ አሁኑኑ Join በማረግ እና ለጓደኛዎ እና ለሚያቁት ሁሉ ሼር ያድርጉ። እናመሰግናለን😍
👉ውድ የ @COTMp ተከታዮች እንዴት ናችሁ ዛሬ ደሞ ስለ ካራክተርስቲክ እስትሬንግዝ እና ካራክተርስቲክ ሎድ ምንድንነው ኣብረን እንይ።
.
➡Characteristic Strength-ማለት የኮንክሪት ወይም የብረት ቴስት አድርገን ለእያንዳንዱ ቴስት ካገኘናቸው ውጤቶች ውስጥ አምስት ፐርሰንቱን ብቻ የሚበልጥ ውጤት ነው ካ - እስትሬንግዝ ማለት፡፡ ወይም ደግሞ 95 ፐርሰንቱ የቴስት ውጤቶች የሚበልጡት ውጤት ነው፡፡ ትንሹ እስትሬንግዝ ነው ማለትይቻላል፡፡
⏩ፎርሙላውም- [ fc = (mean strength)- 1.64(standard
deviation) ]
.
➡Characteristic Load-ማለት ህንፃው በዘመኑ ያጋጥመዋል ተብሎ ከሚታሰበው ውስጥ አምስት ፐርሰንቱ ብቻ የሚበልጡት load ነው፡፡
⏩ፎርሙላውም - [ fk = (mean load) + 1.64(standard
deviation) ]
.
*ካራክተርስቲክ ሎዱንም ሆነ እስትሬንግዙን ስንወስድ በሁለቱም በኩል ህንፃው ሴፍ ነው:: ምክንያቱም እስትሬንግዙን ስንወስድ ህንፃው ትንሽዬ እስትሬንግዝ አለው ብለን ነው የምንወስደው...
*ሎድ ስንወስድ ደግሞ ለትልቁ ሎድ ነው የምንደዝነው..
ፐሮባብሊቲ ፓራሜትሮቹን ( ሚንና ስታንዳርድ ዲቭዬሽን) የምንወስደው ከቴስት ሪዛልቶች ውስጥ ነው፡፡
.
⚡ አሁኑኑ Join በማረግ እና ለጓደኛዎ እና ለሚያቁት ሁሉ ሼር ያድርጉ። እናመሰግናለን😍
.
➡Characteristic Strength-ማለት የኮንክሪት ወይም የብረት ቴስት አድርገን ለእያንዳንዱ ቴስት ካገኘናቸው ውጤቶች ውስጥ አምስት ፐርሰንቱን ብቻ የሚበልጥ ውጤት ነው ካ - እስትሬንግዝ ማለት፡፡ ወይም ደግሞ 95 ፐርሰንቱ የቴስት ውጤቶች የሚበልጡት ውጤት ነው፡፡ ትንሹ እስትሬንግዝ ነው ማለትይቻላል፡፡
⏩ፎርሙላውም- [ fc = (mean strength)- 1.64(standard
deviation) ]
.
➡Characteristic Load-ማለት ህንፃው በዘመኑ ያጋጥመዋል ተብሎ ከሚታሰበው ውስጥ አምስት ፐርሰንቱ ብቻ የሚበልጡት load ነው፡፡
⏩ፎርሙላውም - [ fk = (mean load) + 1.64(standard
deviation) ]
.
*ካራክተርስቲክ ሎዱንም ሆነ እስትሬንግዙን ስንወስድ በሁለቱም በኩል ህንፃው ሴፍ ነው:: ምክንያቱም እስትሬንግዙን ስንወስድ ህንፃው ትንሽዬ እስትሬንግዝ አለው ብለን ነው የምንወስደው...
*ሎድ ስንወስድ ደግሞ ለትልቁ ሎድ ነው የምንደዝነው..
ፐሮባብሊቲ ፓራሜትሮቹን ( ሚንና ስታንዳርድ ዲቭዬሽን) የምንወስደው ከቴስት ሪዛልቶች ውስጥ ነው፡፡
.
⚡ አሁኑኑ Join በማረግ እና ለጓደኛዎ እና ለሚያቁት ሁሉ ሼር ያድርጉ። እናመሰግናለን😍
👉ዛሬ ደሞ ስለ የ cement ኣይነቶች እንማማር @COTMp
.
⏩There are various types of cement used in concrete construction. Each type of cement has its own properties, uses and advantages based on composition materials used during its manufacture.
⏩13 Types of Cement and their Uses👇
1. Ordinary Portland Cement (OPC)
2. Portland Pozzolana Cement (PPC)
3. Rapid Hardening Cement
4. Quick setting cement
5. Low Heat Cement
6. Sulphates resisting cement
7. Blast Furnace Slag Cement
8. High Alumina Cement
9. White Cement
10. Coloured cement
11. Air Entraining Cement
12. Expansive cement
13. Hydrographic cement
.
▶1. Ordinary Portland Cement (OPC)
Ordinary Portland cement is the most widely used type of cement which is
suitable for all general concrete construction.
It is most widely produced
and used type of cement around the world with annual global production of around 3.8 million cubic meters per year.
*This cement is suitable for all type of concrete construction.
▶2. Portland Pozzolana Cement (PPC)
*Portland pozzolana cement is prepared by
grinding pozzolanic clinker with Portland
cement. It is also produced by adding pozzolana with the addition of gypsum or
calcium sulfate or by intimately and uniformly blending portland cement and fine pozzolana.
*This cement has high resistance to various
chemical attacks on concrete compared
with ordinary portland cement and thus it
is widely used. It is used in marine structures, sewage works, sewage works
and for laying concrete under water such
as bridges, piers, dams and mass concrete
works etc.
▶3. Rapid Hardening Cement
*Rapid hardening cement attains high strength in early days it is used in
concrete where formworks are removed at an early stage and is similar to ordinary portland cement (OPC). This cement has
increased lime content and contains higher c3s content and finer grinding which gives greater strength development
than OPC at an early stage.
*The strength of rapid hardening cement at
the 3 days is similar to 7 days strength of
OPC with the same water-cement ratio.
Thus, advantage of this cement is that
formwork can be removed earlier which increases the rate of construction and
decreases cost of construction by saving
formwork cost.
*Rapid hardening cement is used in prefabricated concrete construction, road works, etc.
▶4. Quick setting cement
The difference between the quick setting cement and rapid hardening cement is
that quick setting cement sets earlier while rate of gain of strength is similar to Ordinary Portland Cement, while rapid
hardening cement gains strength quickly.
Form works in both cases can be removed
earlier.
*Quick setting cement is used where works is to be completed in very short period and for concreting in static or running water.
▶5. Low Heat Cement
*Low heat cement is prepared by maintaining the percentage of tricalcium Almunate below 6% by increasing the proportion of C2S. This makes the concrete to produce low heat of hydration and thus is used in mass concrete
*construction like gravity dams, as the low heat of hydration prevents the cracking of concrete due to heat.
*This cement has increased power against sulphates and is less reactive and initial
setting time is greater than OPC.
▶6. Sulphates Resisting Cement
*Sulfate resisting cement is used to reduce the risk of sulphate attack on concrete and thus is used in construction of foundations where soil has high sulphate content.
*This cement has reduced
contents of C3A and C4AF.
Sulfate resisting cement is used in construction exposed to severe sulphate
action by water and soil in places like canals linings, culverts, retaining walls, siphons etc. ...
.
➡ይቀጥላል ...
.
⚡ አሁኑኑ Join በማረግ እና ለጓደኛዎ እና ለሚያቁት ሁሉ ሼር ያድርጉ።
.
⏩There are various types of cement used in concrete construction. Each type of cement has its own properties, uses and advantages based on composition materials used during its manufacture.
⏩13 Types of Cement and their Uses👇
1. Ordinary Portland Cement (OPC)
2. Portland Pozzolana Cement (PPC)
3. Rapid Hardening Cement
4. Quick setting cement
5. Low Heat Cement
6. Sulphates resisting cement
7. Blast Furnace Slag Cement
8. High Alumina Cement
9. White Cement
10. Coloured cement
11. Air Entraining Cement
12. Expansive cement
13. Hydrographic cement
.
▶1. Ordinary Portland Cement (OPC)
Ordinary Portland cement is the most widely used type of cement which is
suitable for all general concrete construction.
It is most widely produced
and used type of cement around the world with annual global production of around 3.8 million cubic meters per year.
*This cement is suitable for all type of concrete construction.
▶2. Portland Pozzolana Cement (PPC)
*Portland pozzolana cement is prepared by
grinding pozzolanic clinker with Portland
cement. It is also produced by adding pozzolana with the addition of gypsum or
calcium sulfate or by intimately and uniformly blending portland cement and fine pozzolana.
*This cement has high resistance to various
chemical attacks on concrete compared
with ordinary portland cement and thus it
is widely used. It is used in marine structures, sewage works, sewage works
and for laying concrete under water such
as bridges, piers, dams and mass concrete
works etc.
▶3. Rapid Hardening Cement
*Rapid hardening cement attains high strength in early days it is used in
concrete where formworks are removed at an early stage and is similar to ordinary portland cement (OPC). This cement has
increased lime content and contains higher c3s content and finer grinding which gives greater strength development
than OPC at an early stage.
*The strength of rapid hardening cement at
the 3 days is similar to 7 days strength of
OPC with the same water-cement ratio.
Thus, advantage of this cement is that
formwork can be removed earlier which increases the rate of construction and
decreases cost of construction by saving
formwork cost.
*Rapid hardening cement is used in prefabricated concrete construction, road works, etc.
▶4. Quick setting cement
The difference between the quick setting cement and rapid hardening cement is
that quick setting cement sets earlier while rate of gain of strength is similar to Ordinary Portland Cement, while rapid
hardening cement gains strength quickly.
Form works in both cases can be removed
earlier.
*Quick setting cement is used where works is to be completed in very short period and for concreting in static or running water.
▶5. Low Heat Cement
*Low heat cement is prepared by maintaining the percentage of tricalcium Almunate below 6% by increasing the proportion of C2S. This makes the concrete to produce low heat of hydration and thus is used in mass concrete
*construction like gravity dams, as the low heat of hydration prevents the cracking of concrete due to heat.
*This cement has increased power against sulphates and is less reactive and initial
setting time is greater than OPC.
▶6. Sulphates Resisting Cement
*Sulfate resisting cement is used to reduce the risk of sulphate attack on concrete and thus is used in construction of foundations where soil has high sulphate content.
*This cement has reduced
contents of C3A and C4AF.
Sulfate resisting cement is used in construction exposed to severe sulphate
action by water and soil in places like canals linings, culverts, retaining walls, siphons etc. ...
.
➡ይቀጥላል ...
.
⚡ አሁኑኑ Join በማረግ እና ለጓደኛዎ እና ለሚያቁት ሁሉ ሼር ያድርጉ።
👆👆👆 ከ ቅድም የቀጠለ @COTMp
.
▶7. Blast Furnace Slag Cement
*Blast furnace slag cement is obtained by grinding the clinkers with about 60% slag and resembles more or less in properties of Portland cement. It can be used for works economic considerations is predominant.
▶8. High Alumina Cement
*High alumina cement is obtained by melting mixture of bauxite and lime and grinding with the clinker.
It is a rapid hardening cement with initial and final setting time of about 3.5 and 5 hours respectively.
*The compressive strength of this cement is very high and more workable than
ordinary portland cement and is used in
*works where concrete is subjected to high temperatures, frost, and acidic action.
▶9. White Cement
*It is prepared from raw materials free from Iron oxide and is a type of ordinary portland cement which is white in color.
*It is costlier and is used for architectural purposes such as precast curtain wall and facing panels, terrazzo surface etc. and for interior and exterior
decorative work like external renderings of buildings, facing slabs, floorings, ornamental concrete products, paths of gardens, swimming pools etc.
▶10. Colored cement
*It is produced by mixing 5- 10% mineral pigments with ordinary cement. They are widely used for decorative works in floors.
▶11. Air Entraining Cement
*Air entraining cement is produced by adding indigenous air entraining agents such as resins, glues, sodium salts of
sulphates etc. during the grinding of clinker.
*This type of cement is especially suited to improve the workability with smaller water cement ratio and to improve frost
resistance of concrete.
▶12. Expansive Cement
*Expansive cement expands slightly with time and does not shrink during and after the time of hardening.
*This cement is mainly used for grouting anchor bolts and prestressed concrete ducts.
▶13. Hydrographic cement
*Hydrographic cement is prepared by mixing water repelling chemicals and has high workability and strength.
*It has the property of repelling water and is unaffected during monsoon or rains. Hydrophobic cement is mainly used for the construction of water structures such dams, water tanks, spillways, water retaining structures etc.
.
⚡ አሁኑኑ Join በማረግ እና ለጓደኛዎ እና ለሚያቁት ሁሉ ሼር ያድርጉ።
.
▶7. Blast Furnace Slag Cement
*Blast furnace slag cement is obtained by grinding the clinkers with about 60% slag and resembles more or less in properties of Portland cement. It can be used for works economic considerations is predominant.
▶8. High Alumina Cement
*High alumina cement is obtained by melting mixture of bauxite and lime and grinding with the clinker.
It is a rapid hardening cement with initial and final setting time of about 3.5 and 5 hours respectively.
*The compressive strength of this cement is very high and more workable than
ordinary portland cement and is used in
*works where concrete is subjected to high temperatures, frost, and acidic action.
▶9. White Cement
*It is prepared from raw materials free from Iron oxide and is a type of ordinary portland cement which is white in color.
*It is costlier and is used for architectural purposes such as precast curtain wall and facing panels, terrazzo surface etc. and for interior and exterior
decorative work like external renderings of buildings, facing slabs, floorings, ornamental concrete products, paths of gardens, swimming pools etc.
▶10. Colored cement
*It is produced by mixing 5- 10% mineral pigments with ordinary cement. They are widely used for decorative works in floors.
▶11. Air Entraining Cement
*Air entraining cement is produced by adding indigenous air entraining agents such as resins, glues, sodium salts of
sulphates etc. during the grinding of clinker.
*This type of cement is especially suited to improve the workability with smaller water cement ratio and to improve frost
resistance of concrete.
▶12. Expansive Cement
*Expansive cement expands slightly with time and does not shrink during and after the time of hardening.
*This cement is mainly used for grouting anchor bolts and prestressed concrete ducts.
▶13. Hydrographic cement
*Hydrographic cement is prepared by mixing water repelling chemicals and has high workability and strength.
*It has the property of repelling water and is unaffected during monsoon or rains. Hydrophobic cement is mainly used for the construction of water structures such dams, water tanks, spillways, water retaining structures etc.
.
⚡ አሁኑኑ Join በማረግ እና ለጓደኛዎ እና ለሚያቁት ሁሉ ሼር ያድርጉ።
❤1
👉Today Tip @COTMp
.
➡ በ አንድ ሜትር ካሬ ምን ያህል ብሎኬት እንጠቀማለን??
⏩የብሎኬት👇
▶ ስፋት =0.4ሜ
▶ቁመት =0.2ሜ
=1/(0.4*0.2)
=12.5
=~13
🚩ስለዚህ በ አንድ ሜትር ካሬ 13 ፍሬ ብሎኬት እንጠቀማለን ማለት ነው።
Join on telegram:- @etconp
Follow us on Instagram:- @etconp
.
➡ በ አንድ ሜትር ካሬ ምን ያህል ብሎኬት እንጠቀማለን??
⏩የብሎኬት👇
▶ ስፋት =0.4ሜ
▶ቁመት =0.2ሜ
=1/(0.4*0.2)
=12.5
=~13
🚩ስለዚህ በ አንድ ሜትር ካሬ 13 ፍሬ ብሎኬት እንጠቀማለን ማለት ነው።
Join on telegram:- @etconp
Follow us on Instagram:- @etconp
👉Today Tip 2 @COTMp
.
➡ Question - አንድ G+22 የሆነ ህንፃ እንዴት ነው ምንም አይነት Column ሳንጠቀም መገንባት የምንችለው??
.
➡Answer - Shear wall በመጠቀም
.
➡ Question - ከ36 ሚ.ሜ በላይ ለሆኑ ፌሮዎች ለምንድነው Lapping የማይፈቀደው??
.
➡Answer - ፌሮዎቹ ሳይዛቸው ትልልቅ ስለሆነ Lap ብናደርጋቸው ሎድ ትራንስፈር እንዲኖር ላፕ ሌንግዙ ረጅም መሆን አለበት በተጨማሪም ሁለቱን አንድ ላይ ማሰሪያ ትልቅ ዲያሜትር ያለው ፌሮ/ ሽቦ ያስፈልገናል - አስቸጋሪ ነው::
.
➡ Question - ሊፍቶች ውስጥ ለምንድነው መስታወት የሚገጠመው??
.
➡Answer - በግድግዳ የተከበበ በጣም ጠባብ ቤት ውስጥ ዝም ብለን ብንቆም ምን ይሰማናል??
ሊፍቶች ከጥበታቸው በተጨማሪ እንቅስቃሴ ስለሚያደርጉ ሰዎች ይሰጋሉ ምን አልባት አደጋ ከተከሰተ ፤ መብራት ከጠፋ l ምናምን ብለው - እናም ሰዎች ፀጉራቸውን እያስተካከሉ ፤ l ውበታቸውን እያደነቁ ምናምን ፈታ
እንዲሉና ሃሳባቸውን እንዲሰረቅ ነው ሊፍት ውስጥ መስታወት የሚገጠመው::
.
👇👇👇👇👇
Join for more updates via the link below;
t.me/COTMp
👆👆👆👆👆
⚡ አሁኑኑ Join በማረግ እና ለጓደኛዎ እና ለሚያቁት ሁሉ ሼር ያድርጉ። እናመሰግናለን።
.
➡ Question - አንድ G+22 የሆነ ህንፃ እንዴት ነው ምንም አይነት Column ሳንጠቀም መገንባት የምንችለው??
.
➡Answer - Shear wall በመጠቀም
.
➡ Question - ከ36 ሚ.ሜ በላይ ለሆኑ ፌሮዎች ለምንድነው Lapping የማይፈቀደው??
.
➡Answer - ፌሮዎቹ ሳይዛቸው ትልልቅ ስለሆነ Lap ብናደርጋቸው ሎድ ትራንስፈር እንዲኖር ላፕ ሌንግዙ ረጅም መሆን አለበት በተጨማሪም ሁለቱን አንድ ላይ ማሰሪያ ትልቅ ዲያሜትር ያለው ፌሮ/ ሽቦ ያስፈልገናል - አስቸጋሪ ነው::
.
➡ Question - ሊፍቶች ውስጥ ለምንድነው መስታወት የሚገጠመው??
.
➡Answer - በግድግዳ የተከበበ በጣም ጠባብ ቤት ውስጥ ዝም ብለን ብንቆም ምን ይሰማናል??
ሊፍቶች ከጥበታቸው በተጨማሪ እንቅስቃሴ ስለሚያደርጉ ሰዎች ይሰጋሉ ምን አልባት አደጋ ከተከሰተ ፤ መብራት ከጠፋ l ምናምን ብለው - እናም ሰዎች ፀጉራቸውን እያስተካከሉ ፤ l ውበታቸውን እያደነቁ ምናምን ፈታ
እንዲሉና ሃሳባቸውን እንዲሰረቅ ነው ሊፍት ውስጥ መስታወት የሚገጠመው::
.
👇👇👇👇👇
Join for more updates via the link below;
t.me/COTMp
👆👆👆👆👆
⚡ አሁኑኑ Join በማረግ እና ለጓደኛዎ እና ለሚያቁት ሁሉ ሼር ያድርጉ። እናመሰግናለን።
Telegram
ETCONp Discussion
📩ለማነኛውም ሀሳብ እና አስተያየት @Philemona7
✌️ይህ የ @etconp መወያያ ግሩፓቹ ነው።
✋This is discussion group of @ETCONpWORK
.
🔖ማሳሰብያ ...
.
⚡️ግሩፑ ላይ ማነኛውም ከ ኮንስትራክሽን ጉዳዮች ውጪ መለጠፍ በፍፁም አይፈቀድም!
@ETCONpBOT ፃፉልን እናመሰግናለን🙏
✌️ይህ የ @etconp መወያያ ግሩፓቹ ነው።
✋This is discussion group of @ETCONpWORK
.
🔖ማሳሰብያ ...
.
⚡️ግሩፑ ላይ ማነኛውም ከ ኮንስትራክሽን ጉዳዮች ውጪ መለጠፍ በፍፁም አይፈቀድም!
@ETCONpBOT ፃፉልን እናመሰግናለን🙏
👍1