Ethio Construction Engineering
32.3K subscribers
6.28K photos
359 videos
1.99K files
3.35K links
🔨 World Construction Engineering
Latest updates, tips, and tutorials on building, civil engineering, and construction in World.
Learn, build, and grow with us!

📨 @Philemona7 Or @ETCONpBOT

For Ad:- https://telega.io/c/etconp
Download Telegram
👉Simple and Quick Field Test Of Bearing Capacity Of Soil

➡️PROCEDURE

1. Excavate a pit of required depth. (preferably equal to the depth of foundation)

2. Take a solid ball or square cube of known weight and dimension.

3. Drop the ball or square cube several times, from a known height on to the bottom surface of excavated pit.

4. Calculate the average depth of impression made several times on the bottom surface of the excavated pit.

*⃣Let “d” is the average depth of impression.

🚧CALCULATION

➡️Calculate the ultimate resistance of soil ( R ) using the formula given below.

*⃣R = (w * h) / d
Where,
⏺R = Ultimate resistance of soil (in kg)
⏺d = Average depth of impression (in cm)
⏺w = Weight of the solid ball or square cube (in kg)
⏺h = Height of fall of solid ball or cube (in cm)

➡️If “A” is the cross sectional area of the solid steel ball or cube, then resistance of soil per unit area is calculated using following formula.

➡️Resistance of soil per unit area (in kg/cm ) = R / A
➡️Safe bearing capacity (in kg/cm ) = R / (A * F.O.S)
Where,
⏺F.O.S = Factor of safety

🚧NOTES TO REMEMBER

*⃣1. F.O.S varies from 2 to 3 depending upon the type of structure and site condition.

*⃣2. In order to get reliable test result, perform this test on different types of soil and then use your judgment to reach at any conclusion.

*⃣3. Instead of using solid steel ball or square cube, we can also use CBR test plunger, or Cone (used for cone penetration test)

➡️PRESUMPTIVE BEARING CAPACITY

▶️ presumptive bearing capacity values for different types of soils (kg/
cm)

⏹Rock 32.40
⏹Soft rock 4.40
⏹Coarse sand 4.40
⏹Medium sand 2.45
⏹Fine sand 4.40
⏹Soft shell / Stiff clay 1.00
⏹Soft clay 1.00
⏹Very soft clay 0.50

➡️NOTES TO REMEMBER

1. For non-cohesive soils the values should be reduced by 50% if the water table is above or near base of footing.

2. These values should be used only for preliminary design.
▶️The actual bearing capacity of soil should be calculated as per the standard codes.

#GeotechnicalEngineering

@etconp
Ethio Construction Engineering
👉What’s wrong with it ? 🚧ችግሩ ምንድን ነው? ✍ሀሳብ እና አስተያየታቹ @COTMp ፃፉልን። Telegram:-@etconp Instagram:- https://instagram.com/etconp?igshid=y7azluxtmxyw
Answer

➪ It’s over reinforced ( densely reinforced) so aggregate can’t pass through it during vibration so it causes honey comb

➪ ብረት (ፌሮ ) ተቀራርቦ ነው የታሰረው ይህም በ vibration ጊዜ ጠጠሮቹ በደንብ circulate ስለማያደርጉ honey comb ይፈጥራል።

Telegram:- @etconp
Instagram:- https://instagram.com/etconp?igshid=y7azluxtmxyw
👉What is Workability Of Concrete?

➡️Workability can be defined as the property of fresh concrete which describes the ease and homogeneity of the concrete to be mixed, fully compacted and finished.

➡️A workable concrete should possess following two requirements:

🚧1. The concrete should be compacted with minimum efforts.

🚧2. The concrete should not form bleeding and segregation.

➡️Workability of concrete mainly depends on the mix proportion and the properties of concreting materials (water, cement, aggregates).

➡️The shape, size, and grades of aggregates also play a great role in the variation of workability.

➡️For better workability fine and coarse aggregates should be well graded.

➡️It has been found that concrete made of round grain sand is more workable than the concrete of crushed sand.

➡️If air entraining admixture is used in the mix, it will also increase the workability and decrease segregation and bleeding.

🏷FACTORS AFFECTING WORKABILITY OF CONCRETE

➡️The factors affecting workability are as following:

🚧1. Amount Of Water In The Mix

🚧2. Proportion Of Coarse And Fine Aggregates: Workability can be increased by decreasing the amount of coarse aggregates in the mix.

*⃣Fine aggregates produce more wore workable concrete.

🚧3. Shape Of aggregates: Round shaped aggregates give better workability than angular shaped aggregates.

🚧4. By expanding the cement content in the mix.

🚧5. By including admixtures in the mix. Apparently, the necessity of workability differs as per the nature of the job and blockage in the full stream of concrete due to the spacing and nature of the reinforcement.

🏷The workability of concrete is generally measured by one of the following three tests

🚧1. Slump Test

🚧2. Compaction Factor Test

🚧3. Vee-Bee Test

#ConcreteTechnology

@etconp
👉Some Questions Asked By Our Channel Members

🏷Part-One


➡️Q1. What is the Unit Weight of concrete?

🚧The unit weight of concrete depends on the type of aggregates and amount of voids.
*⃣As per IS : 456-200 Unit weight of PCC is 24KN/m3 and RCC is 25KN/m3

➡️Q2. What is the unit weight of Steel?

🚧The unit weight of Steel is 78.5KN/m3

➡️Q3. What is ductility?

🚧Ductility is the Ability to deform under tensile stress.

➡️Q4. How to find the weight of steel bar used in reinforcement?

🚧Weight of Bar in kg/m = Dsquare/162.2
*⃣D- Dia of bar in mm

➡️Q5. What’s the difference between one way slab and two-way slab?

🚧One way slab: Ratio of Longer Span / Shorter span > 2

🚧Two way slab: Ratio of Longer span/ shorter span <= 2

➡️Q6. What is flat slab?

🚧The slab which is supported on columns (Flab slab don’t have beams)

➡️Q7. What do you mean by One storeyed, Two storeyed building?

🚧The building which has two floors is called two storeyed building.

➡️Q8. What’s the length of rise and tread in Stair case?

🚧Rise – 150mm to 200mm
🚧Tread – 250mm to
300mm

➡️Q9. What’s the slope of Staircase?

🚧As per IS 456, the slope or pitch of stair should be between 25 degrees to 40 degrees.

➡️Q10. What do you mean by the moment of inertia?

🚧A quantity expressing a body’s tendency to resist angular acceleration, which is the sum of the products of the mass of each particle in the body with the square of its distance from the axis of rotation.

➡️Q11. What is a crank length in the slab?

🚧The crank length in Slab is 0.42 D.
*⃣Where D is Depth of Slab- Top cover – Bottom Cover.

➡️Q12. What are the types of a slump?

🚧True Slump: The concrete mass after the test when slumps evenly all around without disintegration is called the true slump.

🚧Shear Slump: When one half of the concrete mass slide down the other is called the shear slump.
*⃣This type of slump is obtained in a lean concrete mix.

🚧Collapse Slump: When the sample is collapsed due to adding excessive water, it is known as collapse slump.

🚧Zero Slump: For very stiff or dry mixes it does not show any changes of The slump after removing the slump cone.

➡️Q13. What is grouting?

🚧Grout is a fluid form of concrete which is used to fill the voids.

@etconp
Ethio Construction Engineering
👉Some Questions Asked By Our Channel Members 🏷Part-One ➡️Q1. What is the Unit Weight of concrete? 🚧The unit weight of concrete depends on the type of aggregates and amount of voids. *⃣As per IS : 456-200 Unit weight of PCC is 24KN/m3 and RCC is 25KN/m3…
👉Some Questions Asked By Our Channel Members

🏷Part-Two

➡️Q16. What is allowable moisture content in Fine aggregate for the concrete mix?

🚧We won’t use the aggregate if its moisture content is more than 5%.

➡️Q17. What do you mean by segregation?

🚧Segregation is a separation of cement, sand From aggregate.
*⃣This is caused due to Water cement ratio and when concrete is poured about more than 1.5m

➡️Q18. What is Seepage?

🚧Slow percolation of water through soil is called Seepage.

➡️Q19. What is the Compressive Strength of brick?

🚧Second class brick-70kg/cm2

🚧First class brick-105kg/cm2

🚧Fire brick-125kg/cm2

➡️Q20. How do you check the quality of cement on the site?

🚧1. Date of Mfg: Cement strength decreases with its age.

🚧2. Color: Colour should be grey with light greenish shade and it should be uniform.
*⃣Color gives an indication of excess lime or clay.

🚧3. Float test: A good cement won’t float if you throw a cement in water.

🚧4. When you put your hand in cement bag you should feel cool.

Q21 .What Is mean 1BHK full form

🚧1 Bedroom, 1 Hall,1kitchen

➡️Q22. What is Initial & final setting time of concrete?

🚧Intial Setting time : 30 minutes And,Final setting time is 10hrs

➡️Q23. What is durability?

🚧Ability to withstand under pressure is called Durability.

➡️Q24. What are the concrete tests?

🚧Slump test,Compressive strength test, water permeability test, Water absorption test

➡️Q25. What is bleeding in concrete?

🚧Bleeding is one form of segregation, where water comes out to the surface of the concrete, being lowest specific gravity among all the ingredients of concrete.

➡️Q26. What is the name of the machine to get compression test?

🚧Universal testing machine (UTM)

➡️Q27. When we go for Pile foundation?

🚧Pile foundation is adopted when the Soil bearing capacity is less than 24KN/M3

➡️Q28. What is the function of stirrups in the column?

🚧Stirrups are provided to handle the shear force and to hold the rebars (main bars) in position.

@etconp
👍1
👉Different Types of map

🚧Topographical map

➡️Shows the hills, Valleys, rivers, Village, towns, forests etc.

🚧Cadastral map

➡️Showing the boundaries of fields, houses & other properties.

🚧Engineering map

➡️Shows details of engineering works such as roads, railway, reservoirs, irrigation canals etc.

🚧Geological map

➡️Showing areas including underground resources.

🚧Contour map

➡️Determine the capacity of reservoir and to find best possible route for roads & railways

🚧Military map

➡️showing the road & railway communication with different parts of a country such a map also shows the different strategic points important for the defence of a country.

🚧Archeological Map

➡️Showing areas including places where ancient relics exist

#Surveying

@etconp
👉The disadvantage of too much slope

🏷Instagram:- https://instagram.com/etconp?igshid=oqktpb7q0hb4

@etconp
👉Superelevation (Cant) or Banking

➡️It is the transverse inclination of the pavement surface, in which the outer edge is raised with respect to the inner edge.

🚧Superelevation is provided to counteract the effect of centrifugal force and to reduce the tendency of the vehicle to overturn.

🚧Superelevation is expressed as the ratio of the height of outer edge with respect to the horizontal width.

🚧Maximum limits of Superelevation are

1⃣ For plain and rolling terrains in snow bound areas = 7.0 %

2⃣ For hill roads not bound by snow = 10 %

3⃣ For urban road stretches with frequent intersections = 4%

🚧Superelevation should not be less than the Camber of the road surface.

🚧Superelevation should be attained gradually over the full length of transition curve so that the design Superelevation is available at the starting point of the circular curve.

🚧In case where transition curve cannot be provided,2/3rd of the Superelevation may be attained at the straight portion before the start of the circular curve and the balance 1/3rd at the beginning of the circular curve.

🚧Superelevation is introduced by raising the outer edge of the pavement at a rate not exceeding 1 in 150 in plain and rolling terrains and 1 in 60 on mountainous and steep terrain.

#ConstructionNotes

#HighwayEngineering

@etconp
👉Some Highway Engineering Note

🚧A horizontal curve in a highway, is a curve which is provided to change the direction of the central line of the road.

🚧When a vehicle traverses a horizontal curve, the centrifugal force acts horizontally outwards through the centre of gravity of the vehicle.

🚧Centrifugal ratio or Impact factor -- It is the ratio of centrifugal force (P) to the weight of the vehicle ( W) .

🚧Centrifugal force acting on a vehicle negotiating a horizontal curve has two effects

1⃣ Tendency to overturn the vehicle outwards about the outer wheels,
2⃣ Tendency to skid the vehicle laterally outwards.

If, b = Width of the wheel base
h = Height of the center of gravity of the vehicle above the road surface
f = coefficient of lateral friction
Then,
*⃣Overturning of the vehicle will occur when centrifugal ratio is equal to or more than b/2h.
*⃣Lateral skidding will occur when centrifugal ratio is equal to or more than coefficient of lateral friction( f) .

➡️So to avoid Overturning and lateral skidding on a horizontal curve, the centrifugal ratio should always be less than b/2h and also f.

🚧If, f < b/2h then,
Vehicle would skid first and not overturn.

🚧If, f > b/2h then,
Vehicle would overturn first before skidding.

➡️If the pavement is kept horizontal across the alignment, then the pressure on the outer wheels will be higher than the inner wheels, due to the centrifugal force acting outwards.

#HighwayEngineering

@etconp
Ethio Construction Engineering
👉Some Highway Engineering Note 🚧A horizontal curve in a highway, is a curve which is provided to change the direction of the central line of the road. 🚧When a vehicle traverses a horizontal curve, the centrifugal force acts horizontally outwards through…
👉Some Highway Engineering Notes


🚧Stopping distance = Lag distance + Braking distance

▶️Lag distance = Distance travelled by the vehicle during the total reaction time.
▶️Braking distance = Distance travelled by the vehicle after the application of the brakes, to a dead stop position.

🚧In ascending gradients, braking distance decreased.

🚧In descending gradients, braking distance increases.

🚧Stopping sight distance and Stopping distance are different.

🚧Minimum Stopping sight distance = Stopping distance in following cases
(In one way traffic lanes,In two way traffic roads having 2 or more traffic lanes)

🚧Minimum Stopping sight distance = TWICE the Stopping distance in following cases
( On roads with restricted width , On single lane roads when two way movement of traffic is permitted)

🚧The Stopping sight distance (SSD) should be provided throughout the length of all roads and hence this is also known as absolute minimum sight distance.

🚧Higher Stopping sight distance is required in case of descending gradients.

#HighwayEnginnering

#etconp
👍2
👉Methods of Curing

🚧1. Curing by spraying water

➡️Spraying of water continuously on the concrete surface provides an efficient curing. It is mostly used for curing floor slabs.

▶️The concrete should be allowed to set sufficiently before sprinkling is started.

▶️The spray can be obtained from a perforated plastic box. On small jobs sprinkling of water may be done by hand.

▶️Vertical and sloping surfaces can be kept continuously wet by sprinkling water on top surfaces and allowing it to run down between the forms and the concrete. For this method of curing the water requirement is higher.

🚧2. Curing using wet Gunny bags

➡️This is a widely used method of curing, particularly for structural concrete Thus exposed surface of concrete is prevented from drying out by covering it with hessian, canvas or empty cement bags. The covering over vertical and sloping surfaces should be secured properly These are periodically wetted.

▶️The interval of wetting will depend upon the rate of evaporation of water. It should be ensured that the surface of concrete is not allowed to dry even for a short time during the curing period.

▶️Special arrangements for keeping the surface wet must be made at nights and on holidays.

🚧3. Curing by Pounding Method

➡️This is the best method of curing.

▶️It is suitable for curing horizontal surfaces such as floors, roof slabs, road and air field pavements. The horizontal top surfaces of beams can also be Pounded. After placing the concrete, its exposed surface is first covered with moist hessian or canvas. After 24 hours, these covers are removed and small ponds of clay or sand are built across and along the pavements. The area is thus divided into a number of rectangles.

▶️The water is filled between the ponds.

▶️The filling of water in these ponds is done twice or thrice a day, depending upon the atmospheric conditions. Though this method is very efficient, the water requirement is very heavy. Ponds easily break and water flows out. After curing it is difficult to clean the clay.

🚧4. Steam Curing

➡️Steam curing and hot water curing is sometimes adopted. With these methods of curing, the strength development of concrete is very rapid.

▶️These methods can best be used in pre cast concrete work. In steam curing the temperature of steam should be restricted to a maximum of 750C as in the absence of proper humidity (about 90%) the concrete may dry too soon. In case of hot water curing, temperature may be raised to any limit, ay 1000C.

▶️At this temperature, the development of strength is about 70% of 28 days strength after 4 to 5 hours. In both cases, the temperature should be fully controlled to avoid non-uniformity. The concrete should be prevented from rapid drying and cooling which would form cracks.

🚧5. Curing using chemicals

➡️Curing compounds are chemical products usually Sprayed directly over the concrete surface and allowing it to dry.

▶️The compound forms an impermeable membrane that retards the loss of moisture from the concrete.

#ConstructionNotes

#Curing

@etconp
❤1👍1
Media is too big
VIEW IN TELEGRAM
👉ስለነዚህ የተለያዩ አስገራሚ ማሽኖች ታውቃላችሁ?

🚧የመሬት ውስጥ መንገድ ቦርቧሪው፣ ድልድይ ዘርጊው፣ የጡብ መንገድ አንጣፊው፣ ሃዲድ ዘርጊው፣ አሮጌ ህንጻ አፍራሹ እና ሌሎች ቴክኖሎጂዎች በ ምስል አስደግፎ ሰሎሞን ቴክ ቶክ አዘጋጅቶላቹሃል።

🚧ቪድዮ ለማየት ከዚህ ፅሁፍ አያይዘንላቹሀል 166.1MB ስለሆነ WIFI ቢጠቀሙ ይመረጣል።

🎥ወይም በ YOUTUBE ለማየት ከታች ባለው ሊንክ ይከታተሉት

https://youtu.be/gr2Maeyrcnw

Via Tech Talk With Solomon

#ConstructionTechnology

@etconp
Guess the diameter of the bar

@etconp

Instagram:- https://instagram.com/etconp?igshid=h82z1u7h3leg

Facebook:- @etconp
👉ለመላው የክርስትና ዕምነት ተከታዮች እንኳን ለብርሃነ መስቀሉ ደመራ በዓል በሠላም አደረሳችሁ።

🚩በዓሉ የሠላም ፣ የጤና ፣ የፍቅር ፣ የአንድነት ፣ የብልፅግና እንዲሆን ፈጣሪ አምላክ ፍቃዱ ይሁን!"🙏

@etconp
👉ለመላው የክርስትና ዕምነት ተከታዮች እንኳን ለብርሃነ መስቀሉ ደመራ በዓል በሠላም አደረሳችሁ።

🚩በዓሉ የሠላም ፣ የጤና ፣ የፍቅር ፣ የአንድነት ፣ የብልፅግና እንዲሆን ፈጣሪ አምላክ ፍቃዱ ይሁን!"🙏

@etconp
👉What is Liquidated damage?
.
➡ስራ ተቌራጩ ለወሰደው ውል በግዜ ላለመጨረሱ ለባለቤት ወይም ለውል ሰጪው አካል የሚከፍለው የካሳ ክፍያ ነው።

➡️የጠቅላላ ኮንስትራክሽን ውል ይህ ሳይሆን ሲቀር ከዚህ በታች በተጠቀሰው ቅጣት መሰረት ስራ ተቌራጩ መቅጣት እነደሚቻል ይጠቅሳል።

🚧1. ቅጣቱ 0.1 ፐርሰንት ወይም የጠቅላላ ፕሮጀክቱን አንድ አንድ ሺኛ (1/1000) ላልፈፀመው ስራ ቀናት በየቀኑ ሊቀጣ ይገባል።

🚧2. ነገር ግን ስራ ተቌራጩ በጠቅላላው ሊቀጣ የሚችለው የፕሮጀክቱን አስር 10% (አስር ፐርሰንት) ሊበልጥ አይገባም።

⏩"Liquidated damages" means the compensation stated in the contract as being payable by Contractor to the Public Body for failure to perform the contract or part thereof within the periods under the contract, or as payable by Contractor to the Public Body for any specific breach identified in the contract;

🚧(a) A penalty of 0.1% or 1/1000 of the value of undelivered Service for each day of delay until actual delivery or performance.

🚧(b) The cumulative penalty to be paid by the Contractor shall not exceed 10% of the contract price.

#ConstructionLaw

@etconp
Softwares which are used for construction industry

ለ construction industry’ው የምንጠቀማቸው software’ኦች


Facebook:- https://www.facebook.com/115479406977628/posts/120058029853099/?d=n

Instagram:- https://instagram.com/etconp?igshid=h82z1u7h3leg

Telegram:- https://t.me/ETCONp
👉Different parts of an arch are

🚧1. ABUTMENT OR PIER

➡️It is the part of wall or pier on which the arch rests.

🚧2. ARCH RING

➡️It is a course of stones or bricks having a curve similar to that of the arch.

🚧3. INTRADOS OR SOFFIT

➡️It is the under-surface of an arch.

🚧4. EXTRADOS

➡️It is the outer surface of an arch or the outer curve of the arch ring.

🚧5. VOUSSOIRS OR ARCH BLOCK

➡️The wedge-shaped units forming the arch are known as voussoirs or arch stones or arch block.

🚧6. SPRINGING STONE

➡️Springing stone or springer is the first voussoirs at springing level on either side of the arch.

🚧7. SPRINGING LINE

➡️Springing line is an imaginary line joining two springing points.

🚧8. CROWN

➡️Crown is the highest point of the extrados or it is the highest part of the arch.

🚧9. KEY-STONE

➡️It is the highest central wedge-shaped block of an arch.

🚧10. SKEW-BACK

➡️It is the surface of the abutment on which the arch rests.

🚧11. SPAN

➡️Span is the clear horizontal distance between supports.

🚧12. RISE

➡️Rise is the vertical distance between the springing line and the highest point on the intrados.

🚧13. SPRINGING POINT

➡️Springing points are the points at extremities of the intrados.

🚧14. DEPTH OF ARCH

➡️The depth of the arch is the perpendicular distance between the intrados and the extrados.

🚧15. HAUNCH

➡️Haunch of the arch is the portion of the arch situated centrally between the key and skew backs.

🚧16. SPANDRIL

➡️Spandril is the triangular walling enclosed by the extrados of the arch, a horizontal line from the crown of the arch and a perpendicular line from the springing of the outer curves.

#ArcStructure

@etconp
👉ደረጃ(Stair case)
.
🏗ደረጃ አንድ የህንፃ ወሳኝ አካል ነው፡፡
*ሰዎች ከአንድ ፎቅ ወደ ሌላ ፎቅ መሄድ እንዲችሉ በቅደም ተከተል የተቀመጡ ቅደም ተከተሎች ነው።
*ደረጃው በመደበኛ ዲዛይን መርሆዎች መሆን ያለበት እና ሰዎች ደረጃዎቹን በቀላል ሁኔታ ለመደራደር እንዲችሉ በእኩል ደረጃ መሆን አለበት፡፡
.
🚧ደረጃ አንድ የሕንፃ ግንባታ ዋና አካል ነው ፣ መኖሪያ ፣ ቢሮ ወይም የህዝብ መገልገያ።
*የግንባታ ኮዶች መሠረት የተነደፈ እና የተሠራ ነው።
*ደረጃ straight ፣ circular ወይም spiral ሊሆን ይችላል። *ለተጠቃሚዎች ችግር እንዳይፈጥር እና አደጋዎችን ለማስወገድ ታሣቢ መሆን አለበት፡፡
.
⚡️stair design principle
.
ደረጃዎች ከአንድ ፎቅ ወደ ሌላው ወለል ተደራሽነት ለመስጠት ቅደም ተከተል የተደረደሩ way ናቸው፡፡
*እነሱ በህንፃው ምቹ ቦታ መቅረብ አለባቸው፡፡
*ባለብዙ ፎቅ ግንባታ ፣ ምንም እንኳን ከፍ ወዳሉ ፎቆች ለመደበኛ እንቅስቃሴ ከአንድ ፎቅ ወደ ሌላ ቦታ ቢኖሩም፣ እሳት ወይም ሌሎች አደጋዎች ካሉ ደደረጃዎች ለአስቸኳይ መውጣት አስፈላጊ ናቸው ፡፡
.
🙌Technical terms
.
የሚከተሉት ከደረጃ ጋር የተዛመዱ ቴክኒካዊ ቃላት ወይም trminologies ናቸው
.
1. step /እርምጃ-ወደ ላይ ሲወርድ/ ሲወርድ እግሩ የሚቀመጥበት የደረጃ ክፍል ፡፡
.
2. tread - የደረጃው አግድም ክፍል።
.
3. Riser-የደረጃ አንድ ቀጥ ያለ ክፍል ፡፡
.
4. String -ደረጃዎቹን የሚደግፍ ዝንባሌ ያለው አባል ፡፡
.
5. Landing-በእያንዳንዱ በረራ መጨረሻ ላይ የቀረበው አግድም መድረክ ነው ፡፡
.
6. pitch(ማስገቢያ) - የደረጃው ቁመት ነው ፡፡
.
7. Hand railing-እጅን የሚደግፍ ደረጃ ያለው አዝማሚያ አባል ነው ፡፡
.
8 . baluster:- የ hand rail መደገፍያ ቀጥ ያለ መካከለኛ ድጋፍ ነው ፡፡
.
⚡️የሚከተሉት ጥሩ የ ደረጃ ባህሪዎች ናቸው:-

1. ከህንፃው ከሁሉም ጎኖች በቀላሉ መድረስ አለበት

2. አየር መኖር አለበት

3. በእያንዳንዱ flight መጨረሻ ሰፊ landing ሊኖረው ይገባል

4. በመደበኛነት flight ውስጥ ከ 12 ደረጃዎች በላይ መሆን የለበትም።

5. የደረጃዎቹ መነሳት እና መሄዳቸው የተመጣጠነ መሆን ያለበት እና የflight መውጣት እና መውረድ ቀላል ነው ፡፡

6. የእጅ ጣውላ ቢያንስ በደረጃው በአንዱ በኩል መሰጠት አለበት

7. የደረጃው angle ከ 30 እስከ 45 ዲግሪዎች መሆን አለበት ፡፡

🚧(የ ደረጃ ኣይነቶች) Stair types...👇

*Straight stairs
*Quarter-turn stairs
*Dog-legged stairs
*Open-newel stairs
*Circular stairs
*Bifurcated stairs
*Geometrical stairs
*Spiral stairs
.
👉ደረጃዎች ከሚከተሉት ማናቸውም ቁሳቁሶች ይገነባሉ ፡፡
.
*የጡብ ማሳዎች ፣ የድንጋይ ንጣፍ ፣ ጣውላዎች ፣ ብረት ፣ በተጠናከረ የሲሚንቶ ኮንክሪት ሊሰሩ ይችላሉ።
.
#Stair

@etconp
👉WHAT IS LINTEL

➡️Lintel is a horizontal flexural member which spans over the openings in the walls for doors, windows, ventilators, cupboards etc.

➡️The load of masonry above the opening is transferred to the wall by flexural action of the lintel so that frames of doors, windows etc.

➡️The end bearings for the lintel should be at least 200 mm.

➡️The width of lintels is same as that of wall.

➡️Lintels Are various used material Such as:-

⏺(a) Wood
⏺(b) Stone
⏺(c) Brick
⏺(d) R.C.C
⏺(e) Steel.

🚧(a) Wood Lintel

▶️It may be a single piece or may be assembled by joining 2 to 3 pieces.

▶️Sometimes the wooden lintels are strengthened by steel plates at top and bottom

▶️Such lintels are called as flitched beams.

🚧(b) Stone Lintels

▶️Wherever stones are available stone beams are used as lintels.

▶️As stone is weak in tension they can be used only for small spans.

▶️Their depth is kept about 1/10 th span.

▶️Stones are cut to the width of wall and dressed before using as lintels.

🚧(c) Brick Lintels

▶️Well burnt, good quality lintels are laid on ends or edges to form lintels It needs temporary form work at the time of construction.

▶️The lintel is to be cured for 7–14 days before formwork is removed.

▶️Such lintels are useful to span small openings.

🚧(d) R.C.C. Lintels

▶️It is possible to provide R.C.C. lintels of any span required in the building.

▶️They can be isolated or continuous over the openings.

▶️They are provided with suitable reinforcement main reinforcements beings on lower side in the opening.

▶️Nowadays these lintels are used very commonly in buildings.

🚧(e) Steel Lintels

▶️Steel angles or rolled steel I-sections are used as lintels.

▶️Tube separators may be provided to maintain the spacing between the sections.

▶️If the sections are opened to atmospheric action, regular painting is necessary.

▶️Many times they are encased in concrete to avoid maintenance problem.

▶️These lintels can be used for large openings.

@etconp