👉1. ኪነህንጻ እና ቀለም
🏷1.1 ጥቁርና ነጭ ቀለማት በውስጥ እይታ
▶️ከላይ በምስሉ ላይ የሚታየው በአዲሳባ ከተማ በደንበል ህንጻ ውስጥ የሚገኝ የቶሞካ የቡና መጠጫ ካፌ ነው።
🚧ጥቁርንና ነጭ ቀለምን በመጠቀምና ተቃርኖን በማምጣት ውስጣዊ ስሜቱን ህይወት አላብሰውታል።
🚧በተለይ በእንደዚህ ሰዎች ብዙ ግዜአቸውን በማያጠፉባቸው ቦታዎች ላይ ተቃርኖን መጠቀም ሲመከር ፣ ለመኖርያ ቦታ ውስጣዊ ክፍሎች ግን ተደጋጋፊ ቀለማት ይመረጣሉ።
#Architecture
#ColorAndArchitecture
@etconp
🏷1.1 ጥቁርና ነጭ ቀለማት በውስጥ እይታ
▶️ከላይ በምስሉ ላይ የሚታየው በአዲሳባ ከተማ በደንበል ህንጻ ውስጥ የሚገኝ የቶሞካ የቡና መጠጫ ካፌ ነው።
🚧ጥቁርንና ነጭ ቀለምን በመጠቀምና ተቃርኖን በማምጣት ውስጣዊ ስሜቱን ህይወት አላብሰውታል።
🚧በተለይ በእንደዚህ ሰዎች ብዙ ግዜአቸውን በማያጠፉባቸው ቦታዎች ላይ ተቃርኖን መጠቀም ሲመከር ፣ ለመኖርያ ቦታ ውስጣዊ ክፍሎች ግን ተደጋጋፊ ቀለማት ይመረጣሉ።
#Architecture
#ColorAndArchitecture
@etconp
👉ኪነህንጻ እና ቀለም
🏷1.2. ሙሉ ወይም አብላጫ ጥቁር ቀለም።
🚧ከታች በምስሉ ላይ የሚታየው በሊያን ዲዛይን የተሰራ የመኖርያ ቤት ሲሆን የነጭ ተቃርኖ የሌለው ጥቁር ውስጣዊ እይታ ነው።
🚧የቤት ቁሶቹ፣ የተለያዩ አጃቢዎች እንዲሁም ወለሉ ጥቁሮች ናቸው።
🚧በ ቀን በጸሀይ ብርሀን ረጋ የሚያደርግ ቦታ ሲሆን በማታ ደግሞ በወርቃማ ነጥብ መብራት እጅግ የሚያምር አስደማሚ ድባብ ይፈጥራል።
🚧በአገራችን ጥቁርን እጅግም የሚደፍር ዲዛይነርም ሆነ ደንበኛ እንደሌለ እናውቃለን።
#Architecture
#ColorAndArchitecture
@etconp
🏷1.2. ሙሉ ወይም አብላጫ ጥቁር ቀለም።
🚧ከታች በምስሉ ላይ የሚታየው በሊያን ዲዛይን የተሰራ የመኖርያ ቤት ሲሆን የነጭ ተቃርኖ የሌለው ጥቁር ውስጣዊ እይታ ነው።
🚧የቤት ቁሶቹ፣ የተለያዩ አጃቢዎች እንዲሁም ወለሉ ጥቁሮች ናቸው።
🚧በ ቀን በጸሀይ ብርሀን ረጋ የሚያደርግ ቦታ ሲሆን በማታ ደግሞ በወርቃማ ነጥብ መብራት እጅግ የሚያምር አስደማሚ ድባብ ይፈጥራል።
🚧በአገራችን ጥቁርን እጅግም የሚደፍር ዲዛይነርም ሆነ ደንበኛ እንደሌለ እናውቃለን።
#Architecture
#ColorAndArchitecture
@etconp
👉በ ጥያቄያቹ መሠረት ኣንዳንድ ሳይት ላይ የተለመዱ የ አማርኛ ቃላት ይዘንላቹ ቀርበናል
➡️ሰጌቶ = steel saw
➡️ፈረዮ = someone who works with reinforcements
➡️ግሪላ = reinforcement used for the placement of footing
➡️ፎንዶ (bottom soffit) = used as a form work for beam and slab at the bottom.
➡️ስፖንዳ (side board) = used as form work for beams and slabs on vertical sides
➡️መቀሰቻ (brace) = supports a vertical side form work of beam, and column panel diagonally
➡️ስታፋ (stirrup) = shear resistant bar of the column, beams, and shear walls
➡️ቱምቢ (plumb Bob) = it is used to check the perpendicularity of columns.
➡️ከበሌቶ = used To separate Top reinforcement Bar From Top Reinforcement Bar of slab.
➡️ሞዲኖ (profile) = used for setting out works
➡️ሲባጎ (string) = used to maintain alignments
➡️ክራቫት (Yoke) = used to fix the form works together in their position.
✍የተቀሩት እናንተም በመወያያ ግሩፓቹ @COTMp ላይ ፃፉልን።
@etconp
➡️ሰጌቶ = steel saw
➡️ፈረዮ = someone who works with reinforcements
➡️ግሪላ = reinforcement used for the placement of footing
➡️ፎንዶ (bottom soffit) = used as a form work for beam and slab at the bottom.
➡️ስፖንዳ (side board) = used as form work for beams and slabs on vertical sides
➡️መቀሰቻ (brace) = supports a vertical side form work of beam, and column panel diagonally
➡️ስታፋ (stirrup) = shear resistant bar of the column, beams, and shear walls
➡️ቱምቢ (plumb Bob) = it is used to check the perpendicularity of columns.
➡️ከበሌቶ = used To separate Top reinforcement Bar From Top Reinforcement Bar of slab.
➡️ሞዲኖ (profile) = used for setting out works
➡️ሲባጎ (string) = used to maintain alignments
➡️ክራቫት (Yoke) = used to fix the form works together in their position.
✍የተቀሩት እናንተም በመወያያ ግሩፓቹ @COTMp ላይ ፃፉልን።
@etconp
👉5 Ways to Terminate a
Contract
➡️A contract is a legal document that binds at least two parties to one another and requires them to meet certain obligations detailed in the contract.
➡️In some instances, contract termination can occur that will make the contract void of legal binding.
▶️Only the parties involved in the agreement may terminate a contract.
🚧Impossibility of Performance
⏺A contract typically requires one or more parties to do something, which is called performance.
*⃣For example, a company may hire and sign a contract to have a public speaker talk at a company event Once the public speaker fulfills his duties agreed upon in the contract, it is called performance.
*⃣If for some reason it is impossible for the public speaker to fulfill his duties, it is called impossibility of performance or sometimes "frustration."
*⃣For example, if the speaker were seriously injured and no one could replace him, that would be impossibility of performance.
*⃣The company has the right to terminate the contract in this scenario.
🚧Breach of Contract
➡️When a contract is intentionally not honored by one party, it is called a breach of contract and is grounds for contract termination.
▶️A breach of contract may exist because one party failed to meet his obligations at all or did not meet his obligations fully.
*⃣For example, if you purchased a product that did not arrive until a day after the agreed upon delivery date, that is an immaterial breach of contract.
▶️However, if your order did not come until two weeks after the delivery date and it affected your business, then that is a material breach of contract.
▶️Generally, with a material breach of contract, the injured party has the right to seek monetary damages for his losses as well as cancel the agreement.
🚧Termination By Prior Agreement
➡️You may terminate a contract if you and the other party have a prior written agreement that calls for a contract termination because of a specific reason.
▶️The usual name for this type of provision is a break clause.
▶️The agreement must give the details of what qualifies as a reason for contract termination.
▶️It should also state what actions need to take place for one of the parties to terminate the contract.
▶️In most cases, one party must submit a written notice to the other party to terminate the contract.
🚧Rescission of the Contract
➡️A rescission of a contract is when a contract is terminated because an individual misrepresented themselves, acted illegally fraud for example or made a mistake.
*⃣For example, if you bought a house but after further inspection you discover that the seller intentionally hid the poor physical condition of the home, you may possibly rescind the contract.
▶️A contract rescission may take place if one party is not old enough to enter a contract or if a elderly person is not able to make legal decisions because of incapacity.
🚧Completion of the Contract
➡️A contract is essentially terminated once the obligations outlined in the contract are completed.
▶️Parties should keep documentation showing that they fulfilled their contract duties.
▶️Documentation is helpful if the other party tries to later dispute the fulfillment of your contract obligations.
▶️A court of law will require proof of contract fulfillment if a dispute occurs.
#ConstructionLaw
#ContractTermination
@etconp
Contract
➡️A contract is a legal document that binds at least two parties to one another and requires them to meet certain obligations detailed in the contract.
➡️In some instances, contract termination can occur that will make the contract void of legal binding.
▶️Only the parties involved in the agreement may terminate a contract.
🚧Impossibility of Performance
⏺A contract typically requires one or more parties to do something, which is called performance.
*⃣For example, a company may hire and sign a contract to have a public speaker talk at a company event Once the public speaker fulfills his duties agreed upon in the contract, it is called performance.
*⃣If for some reason it is impossible for the public speaker to fulfill his duties, it is called impossibility of performance or sometimes "frustration."
*⃣For example, if the speaker were seriously injured and no one could replace him, that would be impossibility of performance.
*⃣The company has the right to terminate the contract in this scenario.
🚧Breach of Contract
➡️When a contract is intentionally not honored by one party, it is called a breach of contract and is grounds for contract termination.
▶️A breach of contract may exist because one party failed to meet his obligations at all or did not meet his obligations fully.
*⃣For example, if you purchased a product that did not arrive until a day after the agreed upon delivery date, that is an immaterial breach of contract.
▶️However, if your order did not come until two weeks after the delivery date and it affected your business, then that is a material breach of contract.
▶️Generally, with a material breach of contract, the injured party has the right to seek monetary damages for his losses as well as cancel the agreement.
🚧Termination By Prior Agreement
➡️You may terminate a contract if you and the other party have a prior written agreement that calls for a contract termination because of a specific reason.
▶️The usual name for this type of provision is a break clause.
▶️The agreement must give the details of what qualifies as a reason for contract termination.
▶️It should also state what actions need to take place for one of the parties to terminate the contract.
▶️In most cases, one party must submit a written notice to the other party to terminate the contract.
🚧Rescission of the Contract
➡️A rescission of a contract is when a contract is terminated because an individual misrepresented themselves, acted illegally fraud for example or made a mistake.
*⃣For example, if you bought a house but after further inspection you discover that the seller intentionally hid the poor physical condition of the home, you may possibly rescind the contract.
▶️A contract rescission may take place if one party is not old enough to enter a contract or if a elderly person is not able to make legal decisions because of incapacity.
🚧Completion of the Contract
➡️A contract is essentially terminated once the obligations outlined in the contract are completed.
▶️Parties should keep documentation showing that they fulfilled their contract duties.
▶️Documentation is helpful if the other party tries to later dispute the fulfillment of your contract obligations.
▶️A court of law will require proof of contract fulfillment if a dispute occurs.
#ConstructionLaw
#ContractTermination
@etconp
👉በቁፋሮ ወቅት ሳይት ላይ ሊገኙ ስለሚችሉ አንዳንድ ነገሮች
ኮንስትራክሽን ኮንትራት ውል ምን ይላል???
⏩ለምሳሌ: ወርቅ ወይም ሌላ መዐድን ቢገኝ
🚧ምላሹ ከዚህ ፅሁፍ በምስል አያይዘንላቹዋል።
#ConstructionLaw
@etconp
ኮንስትራክሽን ኮንትራት ውል ምን ይላል???
⏩ለምሳሌ: ወርቅ ወይም ሌላ መዐድን ቢገኝ
🚧ምላሹ ከዚህ ፅሁፍ በምስል አያይዘንላቹዋል።
#ConstructionLaw
@etconp
👉ኦሞቲክ ቢዝነስ ግሩፕ በአርባምንጭ ከተማ የሆቴል ግንባታ ስራ ጀመረ!
🚧ድርጅቱ በተለያዩ አካባቢዎች ለመገንባት ካቀዳቸው ሆቴሎች እና ሎጆች/ሪዞርቶች መካከል አንዱ የሆነውን እና ደረጃውን የጠበቀ አለም አቀፍ ሆቴል በአርባምንጭ ከተማ የግንባታ ስራውን በይፋ ጀምሯል።
🚧ኦሞቲክ ቢዝነስ ግሩፕ በኮንታ ልዩ ወረዳ (ጨበራ ጩርጩራ ፓርክ አከባቢ) እና በኬንያ ማሳይ ማራ ፓርክ አካባቢ የሪዞርት/ሎጅ ግንባታ ለመጀመር በእንቅስቃሴ ላይ ሲሆን በደቡብ ክልል ጅንካ ከተማ የሎጅ/ሪዞርት ግንባታ እያካሄደ ይገኛል።
Via elias meseret
@etconp
🚧ድርጅቱ በተለያዩ አካባቢዎች ለመገንባት ካቀዳቸው ሆቴሎች እና ሎጆች/ሪዞርቶች መካከል አንዱ የሆነውን እና ደረጃውን የጠበቀ አለም አቀፍ ሆቴል በአርባምንጭ ከተማ የግንባታ ስራውን በይፋ ጀምሯል።
🚧ኦሞቲክ ቢዝነስ ግሩፕ በኮንታ ልዩ ወረዳ (ጨበራ ጩርጩራ ፓርክ አከባቢ) እና በኬንያ ማሳይ ማራ ፓርክ አካባቢ የሪዞርት/ሎጅ ግንባታ ለመጀመር በእንቅስቃሴ ላይ ሲሆን በደቡብ ክልል ጅንካ ከተማ የሎጅ/ሪዞርት ግንባታ እያካሄደ ይገኛል።
Via elias meseret
@etconp
What is A 360 excavator used for ?
1️⃣. To lift personnel to elevated work
sites
2️⃣. To dig trench , foundation and
basement excavation
3️⃣. To put the camber on road before
laying asphalt
4️⃣. To dewater trenches
Telegram:- @etconp
Instagram:- https://instagram.com/etconp?igshid=y7azluxtmxyw
1️⃣. To lift personnel to elevated work
sites
2️⃣. To dig trench , foundation and
basement excavation
3️⃣. To put the camber on road before
laying asphalt
4️⃣. To dewater trenches
Telegram:- @etconp
Instagram:- https://instagram.com/etconp?igshid=y7azluxtmxyw
👉ጅማ ከተማን አቋርጦ በሚያልፈው የአዌቱ ወንዝ ላይ በዚህ መልኩ ለሚሰራው የወንዝ ዳርቻ ልማት አስተዳደሩ በ2013 ስራውን ለማስጀመር 60 ሚሊዮን ብር መመደቡን ለአረንጓዴ ልማት እና መልካም ገጽታ መጽሔት ዳጉ ገልጿል።
🚧ይኸው የጅማን ከተማ ገጽታ ከፍ ያደርጋል ተብሎ የታመነበት የወንዝ ዳርቻ ፕሮጀክት የሦስት ዓመት ጊዜ እንደተያዘልትም የማዘጋጃ ቤቱ ስራ አስኪያጅ ነግረውናል።
Via Getachew Alemu
@etconp
🚧ይኸው የጅማን ከተማ ገጽታ ከፍ ያደርጋል ተብሎ የታመነበት የወንዝ ዳርቻ ፕሮጀክት የሦስት ዓመት ጊዜ እንደተያዘልትም የማዘጋጃ ቤቱ ስራ አስኪያጅ ነግረውናል።
Via Getachew Alemu
@etconp
👉ጠቅላይ ሚኒስትር ዶ/ር አብይ አህመድ በኦሞ ወንዝ ዳርቻ የሚገኘውን የኮይሻ ሀይድሮፖወር ፕሮጀክትን የጎበኙ ሲሆን 37 በመቶ ሥራው መጠናቀቁንም ገልጸዋል፡፡
🚧ፕሮጀክቱ በከፍተኛ ሁኔታ ተጓትቶ እንደቆየ እና በቅርቡ ግን ሥራው ተጠናክሮ መቀጠሉንም ዶ/ር አብይ በማህበራዊ ትስስር ገጻቸው ገልጸዋል፡፡
🚧በዓመት የ6400 ጊጋዋት አወርስ መጠን ያለው ኃይል እንደሚያመነጭ ይጠበቃልም ብለዋል።
🚧እስካሁን ለ4000 ያህል ሰዎች የሥራ ዕድል ያስገኘ ሲሆን፣ ፕሮጀክቱ ሲቀጥል ለተጨማሪ ሰዎች ሥራን እንደሚፈጥርም ገልጸዋል፡፡
@etconp
🚧ፕሮጀክቱ በከፍተኛ ሁኔታ ተጓትቶ እንደቆየ እና በቅርቡ ግን ሥራው ተጠናክሮ መቀጠሉንም ዶ/ር አብይ በማህበራዊ ትስስር ገጻቸው ገልጸዋል፡፡
🚧በዓመት የ6400 ጊጋዋት አወርስ መጠን ያለው ኃይል እንደሚያመነጭ ይጠበቃልም ብለዋል።
🚧እስካሁን ለ4000 ያህል ሰዎች የሥራ ዕድል ያስገኘ ሲሆን፣ ፕሮጀክቱ ሲቀጥል ለተጨማሪ ሰዎች ሥራን እንደሚፈጥርም ገልጸዋል፡፡
@etconp
Name this machine
Soil mechanics ማስታወስ ይጠይቃል
Instagram:- https://instagram.com/etconp?igshid=y7azluxtmxyw
Telegram:- @etconp
Soil mechanics ማስታወስ ይጠይቃል
Instagram:- https://instagram.com/etconp?igshid=y7azluxtmxyw
Telegram:- @etconp
👉የፕሮጀክቱ ግንባታ ከተጀመረ 3 ወራትን ቢያስቆጥርም በፍጥነት እየተከናወነ ስላለው የመስቀል አደባባይ ግንባታ ፕሮጀክት አጠር ያለ ገለፃ
🚧ምንድነው የሚሠራው?
➡️የፕሮጀክቱ ስያሜ እንደሚገልጸው "ከመስቀል አደባባይ፣ ላጋር መዘጋጃ ቤት" የሚያጠቃልል ምቹ የእግረኛ መንገድ ማስፋት፣ የቅርሶች ጥገና፣ የአጸዶች መትከል፣ የአረንጓዴ ሥፍራዎች ዝግጅት፣ የመኪና ማቆሚያ እና የመስቀል አደባባይን በተሻለ መልክ ማዘጋጀትን (Refurbishment) ያካትታል።
🚧ዲዛይነሩ ማነው?
➡️ፕሮጀክቱ የዲዛይን ግንባታ (Design Build) እንደመሆኑ የግንባታ ሥራውን የተረከበው የቻይናው ሥራ ተቋራጭ በሥሩ ሀገር በቀል የሆነ አማካሪ ቀጥሯል።
➡️የከተማ አስተዳደሩ ደግሞ የዲዛይን ሥራውን እና የግንባታ አስተዳደሩን ሙሉ በሙሉ በሥራ ተቋራጩ የተቀጠረው አማካሪ ቢሮ ላይ ላለመተው በራሱ የዲዛይን ክለሳ (Design Reviewer) አማካሪ በካቢኔው ይሁንታ ቀጥሯል።
🚧በዲዛይኑ እነማን ተሳትፈዋል?
➡️የመስክ ጉብኝት ባደረኩበት ወቅት ዋናው ተቆጣጣሪ አርኪቴክት (Chief Project Architect) እንዳብራሩልኝ የአርኪቴክቸር፣ የቅርስ ጥበቃ (Conservation)፣ የከተማ ዲዛይን (Urban design) ባለሙያዎች የሆኑ በርካታ የአዲስ አበባ ዩኒቨርሲቲ መምህራን አብረው እየሠሩ ይገኛሉ አንዳንዶቹ ዲዛይነሮች የእኔም መምህራን የነበሩ ፕሮፌሰሮች ናቸው።
➡️የመዋቅር ዲዛይኑን (Structural Design) የሚከታተለው አምስት ኪሎ የሚገኘው የምህንድስና ትምህርት ቤት መምህራን ቡድን መሆኑን አረጋግጫለሁ።
➡️ዲዛይኑ ከፍተኛ ጭነት እና ፍንዳታ እንዲቋቋም ታስቦበት መወጋጀቱን ታዝቤአለሁ።
➡️የገፀ ምድር ዲዛይን (Landscape Design) የሚያጠኑ ባለሙያዎች በሥራ ተቋራጩ አማካሪ ሥር ተቀጥረው እየሠሩ ነው።
➡️በእኔ ምርመራ ዲዛይኑ የተሰጠበት አካሄድ የመርህ ጉድለት እንደተጠበቀ ሆኖ ፕሮጀክቱ ግን ሀገሪቱ አሉኝ በምትላቸው ምስጉን የዲዛይን እና የግንባታ ቁጥጥር ባለሙያዎች እጅ ላይ እንዳለ አረጋግጫለሁ።
🚧የሚፈርሱ ቅርሶች አሉን ?
➡️ከመዘጋጃ ቤቱ በላጋር እስከ መስቀል አደባባይ ያሉትን ቅርስ የሆኑ ሕንጻዎች (Heritage Buildings) እና ሐውልቶች (Monuments) አንድ በአንድ ለመጎብኘት እና በግንባታው የሚደርስባቸው ተጽእኖ ይኖር እንደሆን ለማጥናት እድል አግኝቻለሁ።
➡️የፕሮጀክቱ አማካሪ አርኪቴክት በዝርዝር እንዳስረዱኝ እና በግሌ የዲዛይን ጥናቶቹን እንዳየኋቸው አንድም የሚነካም ሆነ የሚፈርስ ህንፃ እና ሃውልት የለም።
➡️በቅርስ ጥበቃ ኤክስፐርቶች ምክር የሚታደሱ እና ከቅርሶቹ ጋር ወደሚሄዱ አገልግሎቶች (Adaptive Reuse) የሚቀየሩ ግን ይኖራሉ።
🚧የመስቀል ደመራ እጣ ?
➡️የዲዛይኑም ሆነ የግንባታው ማዕከል በዩኔስኮ የተመዘገበው የደመራው እና የመስቀል በዓል አከባበር እንደመሆኑ ይህንኑ መንፈሳዊ እሴት ይበልጥ ለማድመቅ እና ምቹ ለማድረግ ብዙ እንደተሠራ ታዝቤአለሁ።
*⃣ለምሳሌ ደመራው የሚተከልበት ቦታ እንደ መንፈሳዊ ትውፊቱ ከታች ጀምሮ የመጣ ድንግል መሬት ላይ እንዲተከል የተሠራ ሲሆን በገጸ ምድሩ ላይ የተለየ ማድመቂያ ዲዛይን (Surface A articulation) ተዘጅቶለታል።
🚧ግንባታው መቼ ይጠናቀቃል?
➡️የፕሮጀክት ቢሮው ባለሙያዎች እንዳስረዱኝ የደመራው መትከያ እና አካባቢው መቀመጫ ደረጃዎች ለ መስቀል ደመራ በዐል ይደርሳሉ ብሎኛል።
➡️ቀሪው የመኪና ማቆሚያ የኤሌክትሮ ሜካኒካል ሥራዎች እስከ ገና (ታህሳስ ወር መጨረሻ) ድረስ ሙሉ በሙሉ እንደሚጠናቀቁ ይጠበቃል።
🚧ማጠቃለያ
➡️ከዚህ ቀደም እንዳነሳሁት በዚህ ፕሮጀክት ላይ የነበሩኝ የመርህ (የቅደም ተከተል፣ የአዋጭነት ጥናት፣ የዲዛይን ውድድር ወዘተ) ቅሬታዎች እንደተጠበቁ ሆነው ሥራውን ግን በምንችለው ሁሉ እንደ ዜጋ ማገዝ አለብን ብዬ አምናለሁ።
➡️በግሌ በዲዛይኑ ውስጥ ቢካተቱ፣ ትኩረት ቢያገኙ የምላቸውን የባለሙያ ሃሳቦች ለማካፈል እድል አግኝቻለሁ።
➡️መንግሥትም የአካሄድ ችግሮቹን ለማረም የዜጎችን ሙያዊ ትችት ለመቀበል በወቃሽነት ብቻ ሳይሆን በገንቢ ሱታፌ (Constructive engagement) በቀናነት ሊያየው ይገባል እላለሁ።
Via Architect Yohannes Mekonnen
@etconp
🚧ምንድነው የሚሠራው?
➡️የፕሮጀክቱ ስያሜ እንደሚገልጸው "ከመስቀል አደባባይ፣ ላጋር መዘጋጃ ቤት" የሚያጠቃልል ምቹ የእግረኛ መንገድ ማስፋት፣ የቅርሶች ጥገና፣ የአጸዶች መትከል፣ የአረንጓዴ ሥፍራዎች ዝግጅት፣ የመኪና ማቆሚያ እና የመስቀል አደባባይን በተሻለ መልክ ማዘጋጀትን (Refurbishment) ያካትታል።
🚧ዲዛይነሩ ማነው?
➡️ፕሮጀክቱ የዲዛይን ግንባታ (Design Build) እንደመሆኑ የግንባታ ሥራውን የተረከበው የቻይናው ሥራ ተቋራጭ በሥሩ ሀገር በቀል የሆነ አማካሪ ቀጥሯል።
➡️የከተማ አስተዳደሩ ደግሞ የዲዛይን ሥራውን እና የግንባታ አስተዳደሩን ሙሉ በሙሉ በሥራ ተቋራጩ የተቀጠረው አማካሪ ቢሮ ላይ ላለመተው በራሱ የዲዛይን ክለሳ (Design Reviewer) አማካሪ በካቢኔው ይሁንታ ቀጥሯል።
🚧በዲዛይኑ እነማን ተሳትፈዋል?
➡️የመስክ ጉብኝት ባደረኩበት ወቅት ዋናው ተቆጣጣሪ አርኪቴክት (Chief Project Architect) እንዳብራሩልኝ የአርኪቴክቸር፣ የቅርስ ጥበቃ (Conservation)፣ የከተማ ዲዛይን (Urban design) ባለሙያዎች የሆኑ በርካታ የአዲስ አበባ ዩኒቨርሲቲ መምህራን አብረው እየሠሩ ይገኛሉ አንዳንዶቹ ዲዛይነሮች የእኔም መምህራን የነበሩ ፕሮፌሰሮች ናቸው።
➡️የመዋቅር ዲዛይኑን (Structural Design) የሚከታተለው አምስት ኪሎ የሚገኘው የምህንድስና ትምህርት ቤት መምህራን ቡድን መሆኑን አረጋግጫለሁ።
➡️ዲዛይኑ ከፍተኛ ጭነት እና ፍንዳታ እንዲቋቋም ታስቦበት መወጋጀቱን ታዝቤአለሁ።
➡️የገፀ ምድር ዲዛይን (Landscape Design) የሚያጠኑ ባለሙያዎች በሥራ ተቋራጩ አማካሪ ሥር ተቀጥረው እየሠሩ ነው።
➡️በእኔ ምርመራ ዲዛይኑ የተሰጠበት አካሄድ የመርህ ጉድለት እንደተጠበቀ ሆኖ ፕሮጀክቱ ግን ሀገሪቱ አሉኝ በምትላቸው ምስጉን የዲዛይን እና የግንባታ ቁጥጥር ባለሙያዎች እጅ ላይ እንዳለ አረጋግጫለሁ።
🚧የሚፈርሱ ቅርሶች አሉን ?
➡️ከመዘጋጃ ቤቱ በላጋር እስከ መስቀል አደባባይ ያሉትን ቅርስ የሆኑ ሕንጻዎች (Heritage Buildings) እና ሐውልቶች (Monuments) አንድ በአንድ ለመጎብኘት እና በግንባታው የሚደርስባቸው ተጽእኖ ይኖር እንደሆን ለማጥናት እድል አግኝቻለሁ።
➡️የፕሮጀክቱ አማካሪ አርኪቴክት በዝርዝር እንዳስረዱኝ እና በግሌ የዲዛይን ጥናቶቹን እንዳየኋቸው አንድም የሚነካም ሆነ የሚፈርስ ህንፃ እና ሃውልት የለም።
➡️በቅርስ ጥበቃ ኤክስፐርቶች ምክር የሚታደሱ እና ከቅርሶቹ ጋር ወደሚሄዱ አገልግሎቶች (Adaptive Reuse) የሚቀየሩ ግን ይኖራሉ።
🚧የመስቀል ደመራ እጣ ?
➡️የዲዛይኑም ሆነ የግንባታው ማዕከል በዩኔስኮ የተመዘገበው የደመራው እና የመስቀል በዓል አከባበር እንደመሆኑ ይህንኑ መንፈሳዊ እሴት ይበልጥ ለማድመቅ እና ምቹ ለማድረግ ብዙ እንደተሠራ ታዝቤአለሁ።
*⃣ለምሳሌ ደመራው የሚተከልበት ቦታ እንደ መንፈሳዊ ትውፊቱ ከታች ጀምሮ የመጣ ድንግል መሬት ላይ እንዲተከል የተሠራ ሲሆን በገጸ ምድሩ ላይ የተለየ ማድመቂያ ዲዛይን (Surface A articulation) ተዘጅቶለታል።
🚧ግንባታው መቼ ይጠናቀቃል?
➡️የፕሮጀክት ቢሮው ባለሙያዎች እንዳስረዱኝ የደመራው መትከያ እና አካባቢው መቀመጫ ደረጃዎች ለ መስቀል ደመራ በዐል ይደርሳሉ ብሎኛል።
➡️ቀሪው የመኪና ማቆሚያ የኤሌክትሮ ሜካኒካል ሥራዎች እስከ ገና (ታህሳስ ወር መጨረሻ) ድረስ ሙሉ በሙሉ እንደሚጠናቀቁ ይጠበቃል።
🚧ማጠቃለያ
➡️ከዚህ ቀደም እንዳነሳሁት በዚህ ፕሮጀክት ላይ የነበሩኝ የመርህ (የቅደም ተከተል፣ የአዋጭነት ጥናት፣ የዲዛይን ውድድር ወዘተ) ቅሬታዎች እንደተጠበቁ ሆነው ሥራውን ግን በምንችለው ሁሉ እንደ ዜጋ ማገዝ አለብን ብዬ አምናለሁ።
➡️በግሌ በዲዛይኑ ውስጥ ቢካተቱ፣ ትኩረት ቢያገኙ የምላቸውን የባለሙያ ሃሳቦች ለማካፈል እድል አግኝቻለሁ።
➡️መንግሥትም የአካሄድ ችግሮቹን ለማረም የዜጎችን ሙያዊ ትችት ለመቀበል በወቃሽነት ብቻ ሳይሆን በገንቢ ሱታፌ (Constructive engagement) በቀናነት ሊያየው ይገባል እላለሁ።
Via Architect Yohannes Mekonnen
@etconp
👍1
👉What are efficient ways to soundproof a room?
🚧Double, Air-gapped Walls
➡️This one was key, especially to keep outside sound out and instrument sounds in (like my drums)
▶️Inside of the cinder block garage, we built a room using 2×4’s (or maybe 2×6’s) We then built an ever-so-slightly smaller room inside of it, leaving about 4″ between the outer wall and the inner one.
▶️This air-gap helped block transmission of sound Inside each wall we used fiberglass insulation.
🚧Double Sheet Rock
➡️On the walls mentioned above we used two sheets of 5/8″ sheet rock, not just one.
▶️This provided more mass, also good for blocking sound.
🚧Foam Egg Crates, Foam Rubber, Carpet
▶️We got lucky and found a dozen sheets of foam egg crate at a building auction and bought it for what one sheet of it would normally cost.
▶️We covered the walls in it We used thick carpet on the floor, and some adhesive foam rubber sheets on the door and outside wall.
🚧Adjacent Mixing tech room
▶️We put the mixing consoles, PC, monitors, and other gear that generated noise in an adjacent room.
▶️If we were doing it “right” I probably would have wired up audio jacks to totally isolate the two rooms, but instead we just put a large conduit between the rooms to run the cabling.
▶️I stuffed the conduit full of rags to block the PC fan sounds.
🚧Angled Window
➡️We put a window between the studio and the mixing room so the tech could see the band and vice versa.
▶️To prevent the sound from going through, we used two panes of glass.
*⃣The one on the mixing room side was mounted in a normal up-and-down position.
*⃣The second pane, on the studio side was mounted at about a 45 degree angle, so sounds would be deflected down toward the floor E.g. (Studio,Mixing Room).
🚧AC outside of the studio The studio got pretty hot with all that insulation, so we had to add a window AC unit.
▶️Putting it in the studio was a no-go, so we mounted it in a window in the garage (outside the studio’s double walls) and then fashioned some ducting to run the cool air into the back corner of the studio.
▶️This kept the compressor noise out.
🚧Treating the gear
➡️Finally, we would pick up rattling from drum stands, clicks of guitar pedals, snare vibrations, etc.
▶️We fixed this as we went things like foam, cardboard, electrical tape, and rags all helped.
#ConstitutionTechnology
@etconp
🚧Double, Air-gapped Walls
➡️This one was key, especially to keep outside sound out and instrument sounds in (like my drums)
▶️Inside of the cinder block garage, we built a room using 2×4’s (or maybe 2×6’s) We then built an ever-so-slightly smaller room inside of it, leaving about 4″ between the outer wall and the inner one.
▶️This air-gap helped block transmission of sound Inside each wall we used fiberglass insulation.
🚧Double Sheet Rock
➡️On the walls mentioned above we used two sheets of 5/8″ sheet rock, not just one.
▶️This provided more mass, also good for blocking sound.
🚧Foam Egg Crates, Foam Rubber, Carpet
▶️We got lucky and found a dozen sheets of foam egg crate at a building auction and bought it for what one sheet of it would normally cost.
▶️We covered the walls in it We used thick carpet on the floor, and some adhesive foam rubber sheets on the door and outside wall.
🚧Adjacent Mixing tech room
▶️We put the mixing consoles, PC, monitors, and other gear that generated noise in an adjacent room.
▶️If we were doing it “right” I probably would have wired up audio jacks to totally isolate the two rooms, but instead we just put a large conduit between the rooms to run the cabling.
▶️I stuffed the conduit full of rags to block the PC fan sounds.
🚧Angled Window
➡️We put a window between the studio and the mixing room so the tech could see the band and vice versa.
▶️To prevent the sound from going through, we used two panes of glass.
*⃣The one on the mixing room side was mounted in a normal up-and-down position.
*⃣The second pane, on the studio side was mounted at about a 45 degree angle, so sounds would be deflected down toward the floor E.g. (Studio,Mixing Room).
🚧AC outside of the studio The studio got pretty hot with all that insulation, so we had to add a window AC unit.
▶️Putting it in the studio was a no-go, so we mounted it in a window in the garage (outside the studio’s double walls) and then fashioned some ducting to run the cool air into the back corner of the studio.
▶️This kept the compressor noise out.
🚧Treating the gear
➡️Finally, we would pick up rattling from drum stands, clicks of guitar pedals, snare vibrations, etc.
▶️We fixed this as we went things like foam, cardboard, electrical tape, and rags all helped.
#ConstitutionTechnology
@etconp
👉9 things That we believe Construction engineer should have👇
🚧1. PPE – Personal Protective Equipment (Boots, Hard Hat, Safety Glasses, Ear Plugs, and Safety Vest)
➡️There is not much to say here that is not abundantly obvious.
➡️Having all of this equipment is standard on construction sites.
➡️Make yourself visible and make yourself safe.
➡️Construction sites can be dangerous places.
➡️Engineers are used to following codes Follow OSHA rules and set a good example.
🚧2. Gloves
➡️Helpful in the cold weather, they are also good to keep your hands clean and safe.
➡️You may be asked to go into old basements that may have had oil spills, sewage backups, mold, or other nasty items.
🚧3. Tape Measure
➡️We use this one on virtually every site visit we make.
➡️Good for checking rebar size and spacing.
➡️Measuring floor joist depths or spans.
➡️Get a good one that can cantilever a long distance without someone holding the other end.
➡️You’ll be by yourself more than you think.
🚧4. Cameras and Photo Reference Car
➡️Take more photos than you think you will need.
➡️Data storage is cheap. ➡️Driving back out to job site for a missed photo is far more expensive.
*⃣Tips: Start with overall photos You might wish you had taken a photo of something specific on the outside of a building.
*⃣Overall photos might give you the opportunity to zoom in on that item after the fact.
➡️Use a reference card to establish scale You will open some photos back in your office only to find that you cannot tell if you’re looking at a 1” wide or ¼” wide crack.
➡️A photo reference card, ruler, or even a well-known object (pencil) will help establish scale.
🚧5. Notepad and Pencil
➡️Pencils work in any weather.
➡️Take good notes.
➡️Document people that are present at your visit, the type of work going on, the time you arrived and the time you left.
🚧6. Small Sledgehammer
➡️A small sledgehammer is great for checking the quality of a lot of materials.
➡️A light tap against concrete or masonry can tell you if it is sound material or if there is a void lurking beneath.
🚧7. Probe (screwdriver steel rod/rebar/Leatherman)
➡️We use a screwdriver to check the soundness of wet wood, quality of mortar joints, the depth of holes, etc.
🚧.8 Collapsible Ladder
➡️You will not need one on every job site.
➡️One for the office is fine. ➡️These lightweight tools allow for very easy access to areas difficult to observe.
➡️Follow OSHA ladder rules; know when they need to be anchored.
🚧9. Safety Harness
➡️OSHA does not require these on man-lifts However, the risk of injury is way too steep.
➡️Get a good harness that is adjustable, but fits you comfortably.
➡️You will not use it often, but when you do, you’ll likely be wearing it for a long period of time.
➡️Careful of using others that may be worn or dirty. Also, remember to keep yours clean and dry.
➡️The harness should be the ‘fall- arrest’ type with a lanyard.
➡️There are many different models depending on the type of work.
@etconp
🚧1. PPE – Personal Protective Equipment (Boots, Hard Hat, Safety Glasses, Ear Plugs, and Safety Vest)
➡️There is not much to say here that is not abundantly obvious.
➡️Having all of this equipment is standard on construction sites.
➡️Make yourself visible and make yourself safe.
➡️Construction sites can be dangerous places.
➡️Engineers are used to following codes Follow OSHA rules and set a good example.
🚧2. Gloves
➡️Helpful in the cold weather, they are also good to keep your hands clean and safe.
➡️You may be asked to go into old basements that may have had oil spills, sewage backups, mold, or other nasty items.
🚧3. Tape Measure
➡️We use this one on virtually every site visit we make.
➡️Good for checking rebar size and spacing.
➡️Measuring floor joist depths or spans.
➡️Get a good one that can cantilever a long distance without someone holding the other end.
➡️You’ll be by yourself more than you think.
🚧4. Cameras and Photo Reference Car
➡️Take more photos than you think you will need.
➡️Data storage is cheap. ➡️Driving back out to job site for a missed photo is far more expensive.
*⃣Tips: Start with overall photos You might wish you had taken a photo of something specific on the outside of a building.
*⃣Overall photos might give you the opportunity to zoom in on that item after the fact.
➡️Use a reference card to establish scale You will open some photos back in your office only to find that you cannot tell if you’re looking at a 1” wide or ¼” wide crack.
➡️A photo reference card, ruler, or even a well-known object (pencil) will help establish scale.
🚧5. Notepad and Pencil
➡️Pencils work in any weather.
➡️Take good notes.
➡️Document people that are present at your visit, the type of work going on, the time you arrived and the time you left.
🚧6. Small Sledgehammer
➡️A small sledgehammer is great for checking the quality of a lot of materials.
➡️A light tap against concrete or masonry can tell you if it is sound material or if there is a void lurking beneath.
🚧7. Probe (screwdriver steel rod/rebar/Leatherman)
➡️We use a screwdriver to check the soundness of wet wood, quality of mortar joints, the depth of holes, etc.
🚧.8 Collapsible Ladder
➡️You will not need one on every job site.
➡️One for the office is fine. ➡️These lightweight tools allow for very easy access to areas difficult to observe.
➡️Follow OSHA ladder rules; know when they need to be anchored.
🚧9. Safety Harness
➡️OSHA does not require these on man-lifts However, the risk of injury is way too steep.
➡️Get a good harness that is adjustable, but fits you comfortably.
➡️You will not use it often, but when you do, you’ll likely be wearing it for a long period of time.
➡️Careful of using others that may be worn or dirty. Also, remember to keep yours clean and dry.
➡️The harness should be the ‘fall- arrest’ type with a lanyard.
➡️There are many different models depending on the type of work.
@etconp
👉ዛሬ ጠዋት በህንድ ሞምባይ የሚገኝ ባለ 3 ፎቅ መኖርያ ተደርምሶ አስር ሰዎች እስከአሁን የሞቱ ሲሆን ከ25 በላይ ሰዎች ፍርስራሽ ውስጥ የተደበቁ ሲሆን ፖሊስ ነፍስ የማዳን ስራ እየሰራ ነው ሲል የሀገሪቱ የአደጋ ምላሽ ግብረ ሀይል ቢሮ በትዊተር ገፁ ፅፏል።
#FirstSafety
@etconp
#FirstSafety
@etconp
👉ኢትዮጵያ በቀጣዮቹ አሥር ዓመታት ሁለት የመዝናኛ (ሪዞርት) ከተማዎችን ልትገነባ መሆኑን የባህልና ቱሪዝም ሚኒስቴር አስታውቋል!
🚧በሚኒስቴሩ የቱሪዝም እቅድ ዘርፍ መሪ አቶ አህመድ መሐመድ እንደተናገሩት፤ ከመዝናኛ ከተሞቹ አንዱ የሚገነባው በታላቁ የኢትዮጵያ ህዳሴ ግድብ ዙሪያ ነው።
🚧ግድቡ ሲጠናቀቅ 70 ገደማ ሰው ሰራሽ ደሴቶች የሚኖረው ሲሆን በሀገሪቱ ዋነኛው የቱሪስት መዳረሻ ይሆናልም ተብሏል።
🚧ሁለተኛው የመዝናኛ ከተማ የሚገነባበት ቦታ የአዋጪነት ጥናት ከተካሄደ በኋላ ይወሰናል ያሉት አቶ አህመድ፤ የመዝናኛ ከተማ ግንባታ የሚከናወነው የግሉ ሴክተርን ጨምሮ በብዙ ባለድርሻ አካላት ተሳትፎ መሆኑንም ተናግረዋል።
🚧ሪዞርቶች በግል ባለሀብቶች እንደሚገነቡ የተናገሩት አቶ አህመድ፤ የመዝናኛ ከተማዎቹ ሀገሪቱ ከቱሪዝም ዘርፍ የምታገኘውን ገቢ ከፍ እንደሚያደርግ ገልጸዋል።
Via WaltaInfo
@etconp
🚧በሚኒስቴሩ የቱሪዝም እቅድ ዘርፍ መሪ አቶ አህመድ መሐመድ እንደተናገሩት፤ ከመዝናኛ ከተሞቹ አንዱ የሚገነባው በታላቁ የኢትዮጵያ ህዳሴ ግድብ ዙሪያ ነው።
🚧ግድቡ ሲጠናቀቅ 70 ገደማ ሰው ሰራሽ ደሴቶች የሚኖረው ሲሆን በሀገሪቱ ዋነኛው የቱሪስት መዳረሻ ይሆናልም ተብሏል።
🚧ሁለተኛው የመዝናኛ ከተማ የሚገነባበት ቦታ የአዋጪነት ጥናት ከተካሄደ በኋላ ይወሰናል ያሉት አቶ አህመድ፤ የመዝናኛ ከተማ ግንባታ የሚከናወነው የግሉ ሴክተርን ጨምሮ በብዙ ባለድርሻ አካላት ተሳትፎ መሆኑንም ተናግረዋል።
🚧ሪዞርቶች በግል ባለሀብቶች እንደሚገነቡ የተናገሩት አቶ አህመድ፤ የመዝናኛ ከተማዎቹ ሀገሪቱ ከቱሪዝም ዘርፍ የምታገኘውን ገቢ ከፍ እንደሚያደርግ ገልጸዋል።
Via WaltaInfo
@etconp
👉Extra Rapid Hardening Cement-Definition, Uses and Advantages
➡️Extra rapid hardening cement is obtained by inter grinding calcium chloride with rapid hardening Portland cement.
➡️The normal addition of calcium chloride should not exceed 2 percent by weight of the rapid hardening cement.
➡️It is necessary that the concrete made by using extra rapid hardening cement should be transported, placed and compacted and finished within about 20 minutes.
➡️It is also necessary that this cement should not be stored for more than a month.
➡️Extra rapid hardening cement accelerates the setting and hardening process.
➡️A large quantity of heat is evolved in a very short time after placing.
➡️The acceleration of setting, hardening, and evolution of this large quantity of heat in the early period of hydration makes the cement very suitable for concreting in cold weather.
➡️The strength of extra rapid hardening cement is about 25 percent higher than that of rapid hardening cement at one or two days and 10–20 percent higher at 7 days.
➡️The gain of strength will disappear with age and at 90 days the strength of extra rapid hardening cement or the ordinary Portland cement may be nearly the same.
➡️There is some evidence that there is a small amount of initial corrosion of reinforcement when extra rapid hardening cement is used, but in general, this effect does not appear to be progressive and as such, there is no harm in using extra rapid hardening cement in reinforced concrete work.
🚧However, its use in prestressed concrete construction is prohibited.
#TypesofCement
#ConcreteTechnology
@etconp
➡️Extra rapid hardening cement is obtained by inter grinding calcium chloride with rapid hardening Portland cement.
➡️The normal addition of calcium chloride should not exceed 2 percent by weight of the rapid hardening cement.
➡️It is necessary that the concrete made by using extra rapid hardening cement should be transported, placed and compacted and finished within about 20 minutes.
➡️It is also necessary that this cement should not be stored for more than a month.
➡️Extra rapid hardening cement accelerates the setting and hardening process.
➡️A large quantity of heat is evolved in a very short time after placing.
➡️The acceleration of setting, hardening, and evolution of this large quantity of heat in the early period of hydration makes the cement very suitable for concreting in cold weather.
➡️The strength of extra rapid hardening cement is about 25 percent higher than that of rapid hardening cement at one or two days and 10–20 percent higher at 7 days.
➡️The gain of strength will disappear with age and at 90 days the strength of extra rapid hardening cement or the ordinary Portland cement may be nearly the same.
➡️There is some evidence that there is a small amount of initial corrosion of reinforcement when extra rapid hardening cement is used, but in general, this effect does not appear to be progressive and as such, there is no harm in using extra rapid hardening cement in reinforced concrete work.
🚧However, its use in prestressed concrete construction is prohibited.
#TypesofCement
#ConcreteTechnology
@etconp
👉What are the steps involved in the concreting process & Describe briefly the various methods of concrete curing.
➡️The major steps involved in the process of concreting are as follows:
⏹1. Batching
⏹2. Mixing
⏹3. Transporting and placing of concrete
⏹4. Compacting.
🚧Batching: The process of measurement of the different materials for the making of concrete is known as batching.
▶️batching is usually done in two ways: volume batching and weight batching.
*⃣In case of volume batching the measurement is done in the form of volume whereas in the case of weight batching it is done by the weight.
🚧Mixing: In order to create good concrete the mixing of the materials should be first done in dry condition and after it wet condition.
▶️The two general methods of mixing are:
*⃣hand mixing and machine mixing.
🚧Transportation and placing of concrete: Once the concrete mixture is created it must be transported to its final location.
▶️The concrete is placed on form works and should always be dropped on its final location as closely as possible.
🚧Compaction of concrete: When concrete is placed it can have air bubbles entrapped in it which can lead to the reduction of the strength by 30%.
▶️In order to reduce the air bubbles the process of compaction is performed. Compaction is generally performed in two ways:
*⃣by hand or by the use of vibrators.
🏷Describe briefly the various methods of concrete curing.
➡️Curing is the process of maintaining the moisture and temperature conditions for freshly deployed concrete.
▶️This is done for small duration of time to allow the hardening of concrete.
▶️The methods that are involved in saving the shrinkage of the concrete includes:
⏺(a) Spraying of water: on walls, and columns can be cured by sprinkling water.
⏺(b) Wet covering of surface: can be cured by using the surface with wet gunny bags or straw
⏺(c) Pounding: the horizontal surfaces including the slab and floors can be cured by stagnating the water.
⏺(d) Steam curing: of prefabricated concrete units steam can be cured by passing it over the units that are under closed chambers it allows faster l curing process and results in faster recovery.
⏺(e) Application of curing compounds: compounds having calcium chloride can be applied on curing surface This keeps the surface wet for a very long time.
#ConcreteTechnology
@etconp
➡️The major steps involved in the process of concreting are as follows:
⏹1. Batching
⏹2. Mixing
⏹3. Transporting and placing of concrete
⏹4. Compacting.
🚧Batching: The process of measurement of the different materials for the making of concrete is known as batching.
▶️batching is usually done in two ways: volume batching and weight batching.
*⃣In case of volume batching the measurement is done in the form of volume whereas in the case of weight batching it is done by the weight.
🚧Mixing: In order to create good concrete the mixing of the materials should be first done in dry condition and after it wet condition.
▶️The two general methods of mixing are:
*⃣hand mixing and machine mixing.
🚧Transportation and placing of concrete: Once the concrete mixture is created it must be transported to its final location.
▶️The concrete is placed on form works and should always be dropped on its final location as closely as possible.
🚧Compaction of concrete: When concrete is placed it can have air bubbles entrapped in it which can lead to the reduction of the strength by 30%.
▶️In order to reduce the air bubbles the process of compaction is performed. Compaction is generally performed in two ways:
*⃣by hand or by the use of vibrators.
🏷Describe briefly the various methods of concrete curing.
➡️Curing is the process of maintaining the moisture and temperature conditions for freshly deployed concrete.
▶️This is done for small duration of time to allow the hardening of concrete.
▶️The methods that are involved in saving the shrinkage of the concrete includes:
⏺(a) Spraying of water: on walls, and columns can be cured by sprinkling water.
⏺(b) Wet covering of surface: can be cured by using the surface with wet gunny bags or straw
⏺(c) Pounding: the horizontal surfaces including the slab and floors can be cured by stagnating the water.
⏺(d) Steam curing: of prefabricated concrete units steam can be cured by passing it over the units that are under closed chambers it allows faster l curing process and results in faster recovery.
⏺(e) Application of curing compounds: compounds having calcium chloride can be applied on curing surface This keeps the surface wet for a very long time.
#ConcreteTechnology
@etconp
👉What do you understand by “preset” during the installation process of bridge bearings?
➡️During the installation of bridge bearings the size of the upper plates is reduced to save the material costs.
➡️This process is known as preset.
➡️Generally the upper bearing plate comprises of the following components:
⏺Length of bearing
⏺2 x irreversible movement.
⏺2 x reversible movement.
➡️The bearing initially is placed right in the middle point of the upper bearing plate.
➡️No directional effects of irreversible movement is considered But since the irreversible movement usually takes place in one direction only the displaced direction is placed away from the midpoint In such cases the length of the upper plate is equal to the length of the length of the bearing + irreversible movement + 2 x reversible movement.
👉Why are steel plates inserted inside bearings in elastomeric bearings?
➡️In order to make a elastomeric bearing act function as a soft spring it should be made to allow it to bulge laterally and also the stiffness compression can be increased by simply increasing the limiting amount of the lateral bulge.
➡️In many cases in order to increase the compression stiffness of the bearing the usage of metal plates is made.
➡️Once steel plates are included in the bearings the freedom of the bulge is restricted dramatically, also the deflection of the bearing is reduced as compared to a bearing without the presence of steel plates.
➡️The tensile stresses of the bearings are induced into the steel plates But the presence of the metal plates does not affect the shear stiffness of the bearings.
👉What reinforcements are used in the process of prestressing?
➡️The major types of reinforcements used in prestressing are:
⏺Spalling Reinforcement: The Spalling stresses leads to stress behind the loaded area of the anchor blocks.
➡️This results in the breaking off of the surface concrete.
➡️The most likely causes of such types of stresses are Poisson`s effects strain interoperability or by the stress trajectory shapes.
⏺Equilibrium reinforcements: This type of reinforcements are required where several anchorages exist where the prestressing loads are applied in a sequential manner.
⏺Bursting Reinforcements: These kinds of stresses occur in cases where the stress trajectories are concave towards the line of action of load.
➡️In order to reduce such stresses reinforcements in the form of bursting is required.
@etconp
➡️During the installation of bridge bearings the size of the upper plates is reduced to save the material costs.
➡️This process is known as preset.
➡️Generally the upper bearing plate comprises of the following components:
⏺Length of bearing
⏺2 x irreversible movement.
⏺2 x reversible movement.
➡️The bearing initially is placed right in the middle point of the upper bearing plate.
➡️No directional effects of irreversible movement is considered But since the irreversible movement usually takes place in one direction only the displaced direction is placed away from the midpoint In such cases the length of the upper plate is equal to the length of the length of the bearing + irreversible movement + 2 x reversible movement.
👉Why are steel plates inserted inside bearings in elastomeric bearings?
➡️In order to make a elastomeric bearing act function as a soft spring it should be made to allow it to bulge laterally and also the stiffness compression can be increased by simply increasing the limiting amount of the lateral bulge.
➡️In many cases in order to increase the compression stiffness of the bearing the usage of metal plates is made.
➡️Once steel plates are included in the bearings the freedom of the bulge is restricted dramatically, also the deflection of the bearing is reduced as compared to a bearing without the presence of steel plates.
➡️The tensile stresses of the bearings are induced into the steel plates But the presence of the metal plates does not affect the shear stiffness of the bearings.
👉What reinforcements are used in the process of prestressing?
➡️The major types of reinforcements used in prestressing are:
⏺Spalling Reinforcement: The Spalling stresses leads to stress behind the loaded area of the anchor blocks.
➡️This results in the breaking off of the surface concrete.
➡️The most likely causes of such types of stresses are Poisson`s effects strain interoperability or by the stress trajectory shapes.
⏺Equilibrium reinforcements: This type of reinforcements are required where several anchorages exist where the prestressing loads are applied in a sequential manner.
⏺Bursting Reinforcements: These kinds of stresses occur in cases where the stress trajectories are concave towards the line of action of load.
➡️In order to reduce such stresses reinforcements in the form of bursting is required.
@etconp
👉What’s wrong with it ?
🚧ችግሩ ምንድን ነው?
✍ሀሳብ እና አስተያየታቹ @COTMp ፃፉልን።
Telegram:-@etconp
Instagram:- https://instagram.com/etconp?igshid=y7azluxtmxyw
🚧ችግሩ ምንድን ነው?
✍ሀሳብ እና አስተያየታቹ @COTMp ፃፉልን።
Telegram:-@etconp
Instagram:- https://instagram.com/etconp?igshid=y7azluxtmxyw