👉What are efficient ways to soundproof a room?
🚧Double, Air-gapped Walls
➡️This one was key, especially to keep outside sound out and instrument sounds in (like my drums)
▶️Inside of the cinder block garage, we built a room using 2×4’s (or maybe 2×6’s) We then built an ever-so-slightly smaller room inside of it, leaving about 4″ between the outer wall and the inner one.
▶️This air-gap helped block transmission of sound Inside each wall we used fiberglass insulation.
🚧Double Sheet Rock
➡️On the walls mentioned above we used two sheets of 5/8″ sheet rock, not just one.
▶️This provided more mass, also good for blocking sound.
🚧Foam Egg Crates, Foam Rubber, Carpet
▶️We got lucky and found a dozen sheets of foam egg crate at a building auction and bought it for what one sheet of it would normally cost.
▶️We covered the walls in it We used thick carpet on the floor, and some adhesive foam rubber sheets on the door and outside wall.
🚧Adjacent Mixing tech room
▶️We put the mixing consoles, PC, monitors, and other gear that generated noise in an adjacent room.
▶️If we were doing it “right” I probably would have wired up audio jacks to totally isolate the two rooms, but instead we just put a large conduit between the rooms to run the cabling.
▶️I stuffed the conduit full of rags to block the PC fan sounds.
🚧Angled Window
➡️We put a window between the studio and the mixing room so the tech could see the band and vice versa.
▶️To prevent the sound from going through, we used two panes of glass.
*⃣The one on the mixing room side was mounted in a normal up-and-down position.
*⃣The second pane, on the studio side was mounted at about a 45 degree angle, so sounds would be deflected down toward the floor E.g. (Studio,Mixing Room).
🚧AC outside of the studio The studio got pretty hot with all that insulation, so we had to add a window AC unit.
▶️Putting it in the studio was a no-go, so we mounted it in a window in the garage (outside the studio’s double walls) and then fashioned some ducting to run the cool air into the back corner of the studio.
▶️This kept the compressor noise out.
🚧Treating the gear
➡️Finally, we would pick up rattling from drum stands, clicks of guitar pedals, snare vibrations, etc.
▶️We fixed this as we went things like foam, cardboard, electrical tape, and rags all helped.
#ConstitutionTechnology
@etconp
🚧Double, Air-gapped Walls
➡️This one was key, especially to keep outside sound out and instrument sounds in (like my drums)
▶️Inside of the cinder block garage, we built a room using 2×4’s (or maybe 2×6’s) We then built an ever-so-slightly smaller room inside of it, leaving about 4″ between the outer wall and the inner one.
▶️This air-gap helped block transmission of sound Inside each wall we used fiberglass insulation.
🚧Double Sheet Rock
➡️On the walls mentioned above we used two sheets of 5/8″ sheet rock, not just one.
▶️This provided more mass, also good for blocking sound.
🚧Foam Egg Crates, Foam Rubber, Carpet
▶️We got lucky and found a dozen sheets of foam egg crate at a building auction and bought it for what one sheet of it would normally cost.
▶️We covered the walls in it We used thick carpet on the floor, and some adhesive foam rubber sheets on the door and outside wall.
🚧Adjacent Mixing tech room
▶️We put the mixing consoles, PC, monitors, and other gear that generated noise in an adjacent room.
▶️If we were doing it “right” I probably would have wired up audio jacks to totally isolate the two rooms, but instead we just put a large conduit between the rooms to run the cabling.
▶️I stuffed the conduit full of rags to block the PC fan sounds.
🚧Angled Window
➡️We put a window between the studio and the mixing room so the tech could see the band and vice versa.
▶️To prevent the sound from going through, we used two panes of glass.
*⃣The one on the mixing room side was mounted in a normal up-and-down position.
*⃣The second pane, on the studio side was mounted at about a 45 degree angle, so sounds would be deflected down toward the floor E.g. (Studio,Mixing Room).
🚧AC outside of the studio The studio got pretty hot with all that insulation, so we had to add a window AC unit.
▶️Putting it in the studio was a no-go, so we mounted it in a window in the garage (outside the studio’s double walls) and then fashioned some ducting to run the cool air into the back corner of the studio.
▶️This kept the compressor noise out.
🚧Treating the gear
➡️Finally, we would pick up rattling from drum stands, clicks of guitar pedals, snare vibrations, etc.
▶️We fixed this as we went things like foam, cardboard, electrical tape, and rags all helped.
#ConstitutionTechnology
@etconp