👉ስለ መሰንጠቅ (cracking)
➡️ብዙ የኮንስትራክሽን ባለሞያዎች መሰንጠቅ በMix design ትክክል አለመሆን ብቻ የሚመጣ ይመስላቸዋል ነገር ግን ለመሰንጠቅ (cracking ) ምክንያት የሚሆኑ መንስኤዎችን ከዚህ በታች እንዲህ ዳስሰናል
🚧[፩] - አነስተኛ ጥራት ያላቸውን ቁሶች የምንጠቀም ከሆነ
▶️አነስተኛ ጥራት ያላቸውን ቁሶች የምንጠቀም ከሆነ መሰንጠቅ (cracking ) ይፈጠራል ስለዚህ የምንጠቀማቸውን ለኮንክሪት ግብዓት የሚሆኑ ቁሶችን (ሲሚንቶ፣ አሸዋ፣ ኮረኮንች) ጥራት መፈተሽ አለብን ኮንክሪቱ የብረት መዋቅር (reinforcement ) ያለው ከሆነ የብረቱን ጥራት መገምገም አለብን።
🚧[፪] - መኮማተር (Shrinkage )
▶️ኮንክሪቱን በምንደባልቅበት እና ውሃ በምናጠጣበት ግዜ (Curing ) ተገቢውን ጥንቃቄ ካልወሰድን መኮማተር (shrinkage) መሰንጠቅን(cracking) ያስከትላል።
▶️መኮማተር (shrinkage) ለትልቅ የኮንክሪት ጥንካሬ በጣም አስፈላጊ ነው አስፈላጊውን የውሃ-ሲሚንቶ መመዛዘን (water cement ratio) ካልተጠቀምን በመኮማተር አማካኝነት መሰንጠቅ ሊፈጠር ይችላል ።
🚧[፫] - ጥራት ያለው Aggregate የማንጠቀም ከሆነ
▶️Aggregate የኮንክሪትን አጠቃላይ ጥንካሬ ይወስንልናል ጥራቱ ጥሩ ያልሆነ Aggregate የምንጠቀም ከሆነ ከሲሚንቶ ጋር ተፈላጊውን ጥምረት (bond) ስለማይፈጥር ግንባታችን ሊሰነጠቅ ይችላል።
🚧[፬] - መዋቅራችን ከአቅም በላይ የሆነ ክብደት ሲያስተናግድ
▶️ግንባታው / መዋቅሩ ተገቢውን ጥንካሬ ሳያገኝ በፊት ለትልቅ ክብደት የሚጋለጥ ከሆነ መሰንጠቅ ይከሰታል።
▶️በተጨማሪም መቀሰቻዎችን እና ቅስቱን (formwork ) ያለጊዜው የሚነሳ ከሆነም ግንባታችንን ለስንጣቆ ያጋልጠዋል።
🚧[፭] - በትክክል ውሃ እንዲጠጣ የማይደረግ ከሆነ (improper curing )
▶️ይህ በአገራችን ከሚስተዋሉ ለመሰንጠቅ ከሚዳርጉ ምክንያቶች ቀዳሚው ነው - ውሃ በትክክል አለማጠጣት።
▶️ኮንክሪት እንደተገነባ በተገቢው ጊዜ እና መጠን ውሃ ሊጠጣት አለበት ።
«ወንድና ሲሚንቶ ካልጠጣ ይሰነጠቃል» አይደል ሚሉት ሰካራም ወንዶች😂
🚧[፮] - የውጥረት ስርጭት (stress distribution ) አለመመጣጠን
▶️በጣም ትልቅ የሆነ የብረት መዋቅርን Mix ratio ትንሽ በሆነ ኮንክሪት የሙሌት ስራ ስንሰራ በብረቱ እና በኮንክሪቱ መካከል ያለ የውጥረት ስርጭት (stress distribution ) non linear ይሆናል ይህ ደግሞ መሰንጠቅን ያስከትላል።
🚧[፯] - በሳይት ላይ የሙሌት (casting ) ስራ ሲሰራ ተገቢ ጥንቃቄ ካልተደረገ እና ለስራው ተገቢ የሆነ ባለሞያ (የቀን ሰራተኛን ጨምሮ) ካልተመደበ መሰንጠቅ (cracking) በሚሰራው ኮንክሪት ላይ መፈጠሩ አይቀርም።
@etconp
➡️ብዙ የኮንስትራክሽን ባለሞያዎች መሰንጠቅ በMix design ትክክል አለመሆን ብቻ የሚመጣ ይመስላቸዋል ነገር ግን ለመሰንጠቅ (cracking ) ምክንያት የሚሆኑ መንስኤዎችን ከዚህ በታች እንዲህ ዳስሰናል
🚧[፩] - አነስተኛ ጥራት ያላቸውን ቁሶች የምንጠቀም ከሆነ
▶️አነስተኛ ጥራት ያላቸውን ቁሶች የምንጠቀም ከሆነ መሰንጠቅ (cracking ) ይፈጠራል ስለዚህ የምንጠቀማቸውን ለኮንክሪት ግብዓት የሚሆኑ ቁሶችን (ሲሚንቶ፣ አሸዋ፣ ኮረኮንች) ጥራት መፈተሽ አለብን ኮንክሪቱ የብረት መዋቅር (reinforcement ) ያለው ከሆነ የብረቱን ጥራት መገምገም አለብን።
🚧[፪] - መኮማተር (Shrinkage )
▶️ኮንክሪቱን በምንደባልቅበት እና ውሃ በምናጠጣበት ግዜ (Curing ) ተገቢውን ጥንቃቄ ካልወሰድን መኮማተር (shrinkage) መሰንጠቅን(cracking) ያስከትላል።
▶️መኮማተር (shrinkage) ለትልቅ የኮንክሪት ጥንካሬ በጣም አስፈላጊ ነው አስፈላጊውን የውሃ-ሲሚንቶ መመዛዘን (water cement ratio) ካልተጠቀምን በመኮማተር አማካኝነት መሰንጠቅ ሊፈጠር ይችላል ።
🚧[፫] - ጥራት ያለው Aggregate የማንጠቀም ከሆነ
▶️Aggregate የኮንክሪትን አጠቃላይ ጥንካሬ ይወስንልናል ጥራቱ ጥሩ ያልሆነ Aggregate የምንጠቀም ከሆነ ከሲሚንቶ ጋር ተፈላጊውን ጥምረት (bond) ስለማይፈጥር ግንባታችን ሊሰነጠቅ ይችላል።
🚧[፬] - መዋቅራችን ከአቅም በላይ የሆነ ክብደት ሲያስተናግድ
▶️ግንባታው / መዋቅሩ ተገቢውን ጥንካሬ ሳያገኝ በፊት ለትልቅ ክብደት የሚጋለጥ ከሆነ መሰንጠቅ ይከሰታል።
▶️በተጨማሪም መቀሰቻዎችን እና ቅስቱን (formwork ) ያለጊዜው የሚነሳ ከሆነም ግንባታችንን ለስንጣቆ ያጋልጠዋል።
🚧[፭] - በትክክል ውሃ እንዲጠጣ የማይደረግ ከሆነ (improper curing )
▶️ይህ በአገራችን ከሚስተዋሉ ለመሰንጠቅ ከሚዳርጉ ምክንያቶች ቀዳሚው ነው - ውሃ በትክክል አለማጠጣት።
▶️ኮንክሪት እንደተገነባ በተገቢው ጊዜ እና መጠን ውሃ ሊጠጣት አለበት ።
«ወንድና ሲሚንቶ ካልጠጣ ይሰነጠቃል» አይደል ሚሉት ሰካራም ወንዶች😂
🚧[፮] - የውጥረት ስርጭት (stress distribution ) አለመመጣጠን
▶️በጣም ትልቅ የሆነ የብረት መዋቅርን Mix ratio ትንሽ በሆነ ኮንክሪት የሙሌት ስራ ስንሰራ በብረቱ እና በኮንክሪቱ መካከል ያለ የውጥረት ስርጭት (stress distribution ) non linear ይሆናል ይህ ደግሞ መሰንጠቅን ያስከትላል።
🚧[፯] - በሳይት ላይ የሙሌት (casting ) ስራ ሲሰራ ተገቢ ጥንቃቄ ካልተደረገ እና ለስራው ተገቢ የሆነ ባለሞያ (የቀን ሰራተኛን ጨምሮ) ካልተመደበ መሰንጠቅ (cracking) በሚሰራው ኮንክሪት ላይ መፈጠሩ አይቀርም።
@etconp
GEOTECHNICAL ENGINEERING
THE RATIO OF VOLUME OF AIR TO THE VOLUME OF TOTAL VOID IS :______________?
THE RATIO OF VOLUME OF AIR TO THE VOLUME OF TOTAL VOID IS :______________?
Anonymous Quiz
26%
Porosity
30%
Air content
31%
Void ratio
13%
Percentage of air void
Ethio Construction Engineering
GEOTECHNICAL ENGINEERING
THE RATIO OF VOLUME OF AIR TO THE VOLUME OF TOTAL VOID IS :______________?
THE RATIO OF VOLUME OF AIR TO THE VOLUME OF TOTAL VOID IS :______________?
Geotechnical Engineering
The ratio of volume of air to the volume of total void is :________?
1️⃣. Porosity
2️⃣. Air content
3️⃣. Percentage of air void
4️⃣. Void ratio
@etconp
Instagram:-https://instagram.com/etconp?igshid=h82z1u7h3leg
Facebook:- https://www.facebook.com/115479406977628/posts/120058029853099/?d=n
Please update your telegram
The ratio of volume of air to the volume of total void is :________?
1️⃣. Porosity
2️⃣. Air content
3️⃣. Percentage of air void
4️⃣. Void ratio
@etconp
Instagram:-https://instagram.com/etconp?igshid=h82z1u7h3leg
Facebook:- https://www.facebook.com/115479406977628/posts/120058029853099/?d=n
Please update your telegram
👉WHAT IS STRUCTURAL ANALYSIS? CONCEPTS & LOADS ON STRUCTURE
➡️Structural analysis of structure is essential before starting construction work.
➡️It provides the details of the size of the foundation, size of column and beam, and reinforcement details which is sufficient to carry the load acting on the structure.
➡️Before constructing any structure, there are several documents required like plan, elevation & section details.
➡️This process of finding out the load that a structure can carry safely, without failure is called structural analysis.
🏷Structural Elements/Members
➡️Loads Acting on a Structure are
⏺1. Dead Loads
⏺2. Imposed Loads
⏺3. Live Load
⏺4. Crane load
⏺5. Wave Load
⏺6. Earth Pressure Load
⏺7. Impact Load
⏺8. Wind Loads
⏺9. Earthquake Loads
🏷Basic Concept of Structural Analysis:
*⃣1. Idealization of Structure:
*⃣2. Threats on Structures:
*⃣2. Calculating the response of Structure under the Threat:
*⃣3. Calculation of Internal Stresses:
*⃣4. Efficiency of the Structure:
*⃣5. Analysis of Determinate Structures:
*⃣6. For Plane Truss and Frame:
*⃣7. Analysis of Indeterminate Structures:
*⃣8. For Beams, Plane Truss and Frame:
➡️The most general definition of a structure is a building or an object made from several parts.
➡️From an engineering point of view, the structure may be defined as follows
*⃣The structure is composed of a number of components or elements connected together by joints or supports to fulfill the function for which it is constructed; in such a way that they can transmit the forces coming on the structure to the foundation safely without showing considerable deformation
➡️The concept of structural analysis is applied not only in building constructions but also in our day-to-day life.
*⃣For instance,The aluminum container for carrying food parcels is provided with vertical ribs, which can impart stiffness to it As a result, it becomes easier to carry it without bending.
🏷Importance of Structural Analysis:
➡️To know the behavior of the structure under the loaded condition.
➡️To know the maximum load up to which the structure can be loaded, so that the structure will not fail.
➡️To ensure that the displacement and deformation remain in the permissible limits.
➡️Some of the structural elements are mentioned below:
🚧Structural Analysis Beam: A horizontal member transmitting transverse loads.
▶️Resists loads applied laterally to the beam axis.
▶️The load produces shear and bending moment in the beam.
🚧Column: A vertical member carrying only gravity loads.
▶️It transmits axial force or bending force.
🚧Truss : A structure having slender members connected by pin-joint.
▶️It carries axial load only, applied at joints.
▶️Members undergo either compression or tension.
🚧Grid : Network of beams intersecting each other at right angles.
▶️Vertical loading is transmitted through grids.
🚧Frame : Network of beams and columns with rigid joints.
🚧Plates: Members carrying bending in two directions are called plate structures.
➡️Continuum mechanics principles are followed in their analysis.
*⃣Concrete flat slab is an example of a plate structure
▶️Arch: Members carrying compression in one direction only.
⚡️We Will Continued....
#Structure
@etconp
➡️Structural analysis of structure is essential before starting construction work.
➡️It provides the details of the size of the foundation, size of column and beam, and reinforcement details which is sufficient to carry the load acting on the structure.
➡️Before constructing any structure, there are several documents required like plan, elevation & section details.
➡️This process of finding out the load that a structure can carry safely, without failure is called structural analysis.
🏷Structural Elements/Members
➡️Loads Acting on a Structure are
⏺1. Dead Loads
⏺2. Imposed Loads
⏺3. Live Load
⏺4. Crane load
⏺5. Wave Load
⏺6. Earth Pressure Load
⏺7. Impact Load
⏺8. Wind Loads
⏺9. Earthquake Loads
🏷Basic Concept of Structural Analysis:
*⃣1. Idealization of Structure:
*⃣2. Threats on Structures:
*⃣2. Calculating the response of Structure under the Threat:
*⃣3. Calculation of Internal Stresses:
*⃣4. Efficiency of the Structure:
*⃣5. Analysis of Determinate Structures:
*⃣6. For Plane Truss and Frame:
*⃣7. Analysis of Indeterminate Structures:
*⃣8. For Beams, Plane Truss and Frame:
➡️The most general definition of a structure is a building or an object made from several parts.
➡️From an engineering point of view, the structure may be defined as follows
*⃣The structure is composed of a number of components or elements connected together by joints or supports to fulfill the function for which it is constructed; in such a way that they can transmit the forces coming on the structure to the foundation safely without showing considerable deformation
➡️The concept of structural analysis is applied not only in building constructions but also in our day-to-day life.
*⃣For instance,The aluminum container for carrying food parcels is provided with vertical ribs, which can impart stiffness to it As a result, it becomes easier to carry it without bending.
🏷Importance of Structural Analysis:
➡️To know the behavior of the structure under the loaded condition.
➡️To know the maximum load up to which the structure can be loaded, so that the structure will not fail.
➡️To ensure that the displacement and deformation remain in the permissible limits.
➡️Some of the structural elements are mentioned below:
🚧Structural Analysis Beam: A horizontal member transmitting transverse loads.
▶️Resists loads applied laterally to the beam axis.
▶️The load produces shear and bending moment in the beam.
🚧Column: A vertical member carrying only gravity loads.
▶️It transmits axial force or bending force.
🚧Truss : A structure having slender members connected by pin-joint.
▶️It carries axial load only, applied at joints.
▶️Members undergo either compression or tension.
🚧Grid : Network of beams intersecting each other at right angles.
▶️Vertical loading is transmitted through grids.
🚧Frame : Network of beams and columns with rigid joints.
🚧Plates: Members carrying bending in two directions are called plate structures.
➡️Continuum mechanics principles are followed in their analysis.
*⃣Concrete flat slab is an example of a plate structure
▶️Arch: Members carrying compression in one direction only.
⚡️We Will Continued....
#Structure
@etconp
Ethio Construction Engineering
👉WHAT IS STRUCTURAL ANALYSIS? CONCEPTS & LOADS ON STRUCTURE ➡️Structural analysis of structure is essential before starting construction work. ➡️It provides the details of the size of the foundation, size of column and beam, and reinforcement details which…
👉LOADS ACTING ON A STRUCTURE
🚧1. Dead Loads
➡️The loads on the structure due to the self weight of the building and the weight of the permanent furniture are classified as dead loads.
➡️To calculate dead load, Assess the quantity of the material Multiply it by the unit weight of the material
➡️Dead Load = Quantity of Material x Unit Weight The unit weights of the material.
🚧2. Imposed Loads
➡️The loads that are ‘imposed’ on the structure are called imposed load.
🚧3. Live Load
➡️The loads which change their position with respect to time are called live loads.
E.g., weight of a person, furniture, moving partitions, etc.
➡️The minimum values to be taken for the design purpose are given in EBCS based on the occupancy of the building, i.e., whether the structure is residential, warehouse, etc.
🚧4. Crane load
➡️Loads from the crane and other moving machinery is called crane load.
➡️These loads are vital for the structure If they are not considered, then the structure may undergo failure during its erection itself!
➡️These loads can be known from the manufacturer’s data.
🚧5. Wave Load
➡️For off-shore structures, these loads are essential
e.g., force exerted by water current to the bridge piers, abutments, and other waterfront structures These are random loads, and specialists with enough experience are needed to determine them.
🚧6. Earth Pressure Load
➡️The pressure exerted by the soil on the structures or part of structure embedded partly or fully in the ground is called earth pressure.
➡️These loads are required for the foundation of the structures.
➡️These are also needed for the design of retaining walls, underground water tanks, culverts, bridges, etc.
🚧7. Impact Load
➡️The structures carrying moving loads are to be designed for impact loads.
e.g., bridge
🚧8. Wind Loads
➡️The force exerted on the structures by the horizontal component of the wind is considered under the wind load.
➡️It is considered for the design of tall buildings.
🚧9. Earthquake Loads
➡️the earthquake causes shaking of ground in all directions, and role reversal in the structural elements take place.
➡️As the ground shakes horizontally, horizontal inertia forces are generated.
➡️These lateral forces are transferred through slabs, beams, and columns.
➡️And Columns that are designed to carry compressive loads start getting tensile loads too.
*⃣So, the lateral forces are evaluated to make the structure earthquake resistant.
🏷The following values are needed to be for executing any structural analysis,
⏺Material properties (To know the value of Elastic Modulus)
⏺Structural load
⏺Support conditions
⏺Geometry
🏷As you complete the Structural analysis, you will have the values of:
*⃣Support reactions
*⃣Displacement value
*⃣Stress in the member
➡️These values are then compared to the criteria for structural failure to conclude how much load the member will be able to resist.
🏷Classification of Structures
🚧Based on Type
⏺1. Solid structure
⏺2. Frame structure
⏺3. Membrane structure
⏺4. Composite structure
🚧Based on Form
⏹1. 1-D structures: Rope, cable. Strut, beam, column, and arch
⏹2. 2-D structures: slab, membranes, domes, and plates
⏹3. 3-D structures: Solid masses
🚧Based on Determinacy of the structure
*⃣1. Determinate structure
▶️The structure whose support reactions and internal forces in the members can be found out from the equations of static equilibrium is called a statically determinate structure.
*⃣2. Indeterminate structures
▶️The structure whose support reactions and internal forces in the members can NOT be found out from the equations of static equilibrium is called a statically indeterminate structure.
▶️Indeterminate structures are further classified into statically or kinematically indeterminate structures.
⚡️We Will Continued
#Structure
@etconp
🚧1. Dead Loads
➡️The loads on the structure due to the self weight of the building and the weight of the permanent furniture are classified as dead loads.
➡️To calculate dead load, Assess the quantity of the material Multiply it by the unit weight of the material
➡️Dead Load = Quantity of Material x Unit Weight The unit weights of the material.
🚧2. Imposed Loads
➡️The loads that are ‘imposed’ on the structure are called imposed load.
🚧3. Live Load
➡️The loads which change their position with respect to time are called live loads.
E.g., weight of a person, furniture, moving partitions, etc.
➡️The minimum values to be taken for the design purpose are given in EBCS based on the occupancy of the building, i.e., whether the structure is residential, warehouse, etc.
🚧4. Crane load
➡️Loads from the crane and other moving machinery is called crane load.
➡️These loads are vital for the structure If they are not considered, then the structure may undergo failure during its erection itself!
➡️These loads can be known from the manufacturer’s data.
🚧5. Wave Load
➡️For off-shore structures, these loads are essential
e.g., force exerted by water current to the bridge piers, abutments, and other waterfront structures These are random loads, and specialists with enough experience are needed to determine them.
🚧6. Earth Pressure Load
➡️The pressure exerted by the soil on the structures or part of structure embedded partly or fully in the ground is called earth pressure.
➡️These loads are required for the foundation of the structures.
➡️These are also needed for the design of retaining walls, underground water tanks, culverts, bridges, etc.
🚧7. Impact Load
➡️The structures carrying moving loads are to be designed for impact loads.
e.g., bridge
🚧8. Wind Loads
➡️The force exerted on the structures by the horizontal component of the wind is considered under the wind load.
➡️It is considered for the design of tall buildings.
🚧9. Earthquake Loads
➡️the earthquake causes shaking of ground in all directions, and role reversal in the structural elements take place.
➡️As the ground shakes horizontally, horizontal inertia forces are generated.
➡️These lateral forces are transferred through slabs, beams, and columns.
➡️And Columns that are designed to carry compressive loads start getting tensile loads too.
*⃣So, the lateral forces are evaluated to make the structure earthquake resistant.
🏷The following values are needed to be for executing any structural analysis,
⏺Material properties (To know the value of Elastic Modulus)
⏺Structural load
⏺Support conditions
⏺Geometry
🏷As you complete the Structural analysis, you will have the values of:
*⃣Support reactions
*⃣Displacement value
*⃣Stress in the member
➡️These values are then compared to the criteria for structural failure to conclude how much load the member will be able to resist.
🏷Classification of Structures
🚧Based on Type
⏺1. Solid structure
⏺2. Frame structure
⏺3. Membrane structure
⏺4. Composite structure
🚧Based on Form
⏹1. 1-D structures: Rope, cable. Strut, beam, column, and arch
⏹2. 2-D structures: slab, membranes, domes, and plates
⏹3. 3-D structures: Solid masses
🚧Based on Determinacy of the structure
*⃣1. Determinate structure
▶️The structure whose support reactions and internal forces in the members can be found out from the equations of static equilibrium is called a statically determinate structure.
*⃣2. Indeterminate structures
▶️The structure whose support reactions and internal forces in the members can NOT be found out from the equations of static equilibrium is called a statically indeterminate structure.
▶️Indeterminate structures are further classified into statically or kinematically indeterminate structures.
⚡️We Will Continued
#Structure
@etconp
❤1
Ethio Construction Engineering
👉LOADS ACTING ON A STRUCTURE 🚧1. Dead Loads ➡️The loads on the structure due to the self weight of the building and the weight of the permanent furniture are classified as dead loads. ➡️To calculate dead load, Assess the quantity of the material Multiply…
👉EQUATION OF STATIC EQUILIBRIUM
➡️The structure should remain in equilibrium after a load is applied to it.
➡️no component of the structure should exhibit motion on the application of load.
➡️If the structure possesses sufficient rigidity to develop reactions in response to the loads applied on it, then the equilibrium of the structure is achieved.
➡️To check whether a structure will be in equilibrium or not, three mathematical equations are developed for two dimensional structures, and six mathematical equations are developed for three-dimensional structures.
🏷For 2-D Structures,
▶️The following 3 conditions should be fulfilled
⏺1. The summation of the forces in the horizontal direction should be zero.
⏺2. The summation of the forces in the vertical direction should be zero.
⏺3. The summation of the moments about the direction perpendicular to both the above forces should be zero.
🏷For 3-D Structures,
The following 6 conditions should be fulfilled
*⃣1. The summation of the forces in the horizontal direction (X ) should be zero
*⃣2. The summation of the forces in the vertical direction( Y ) should be zero
*⃣3. The summation of the forces in the direction perpendicular to both horizontal and vertical directions (Z) should be zero
*⃣4. The summation of the moments in the horizontal direction( X ) should be zero
*⃣5. The summation of the moments in the vertical direction( Y ) should be zero
*⃣6. The summation of the moments about the direction perpendicular to both horizontal and vertical directions (Z) forces should be zero
➡️Equilibrium Conditions for 3D Structural Analysis
▶️The structural analysis can be completed by applying the following step-by-step procedure
⏺1. Idealization of Structure
▶️For structural analysis, idealization of the structural system is done to simplify the structure and making the calculations simpler and easier.
➡️Some of the idealizations that we are aware are list below
⏺We assume the beam as a line structure The joints of a truss are pin jointed. In truss, we assume loads are acting only on joints; the loads acting on members cause bending moments, which is not suitable for the truss And as we have assumed truss to possess pin or hinge joints, it cannot take bending moments.
⏺2. Threats on Structures
▶️The threats on structures are the forces acting on it, which tends to reduce its capacity and stability.
▶️These can be in the form of various loads, as discussed earlier.
*⃣Concentrated load
*⃣Distributed load
*⃣Concentrated moment
*⃣Distributed moment
⏺3. Calculating the response of Structure under the Threat
▶️Response of Structure Internal force (axial, shear or moment) Defection
⏺4. Calculation of Internal Stresses
▶️Internal stresses include: Bending stresses : Caused by the bending moment,Shear stresses Caused by the shear force.
⏺5. Efficiency of the Structure
▶️Efficiency : The structural efficiency is the measure of the mass of a structure to the load it can support safely without excessive deformation and deflections.
▶️If a structure is lighter and supports heavy loads, then its efficiency is deemed higher.
⏺6. Analysis of Determinate Structures
▶️The following methods may be implemented for the analysis of the Determinate Structures, For Beams,
▶️Macaulay’s method ,Moment area method,Conjugate beam method,Consistent Deformation method From Influence Line Diagrams
⏺7. For Plane Truss and Frame:
🚧Method of Joints
🚧Method of Sections
🚧Unit load method From Influence Line Diagrams
⏺8. Analysis of Indeterminate Structures:
▶️Compatibility equations and Principle of Superposition are mostly applied during the analysis of indeterminate structures.
▶️The following methods may be implemented for the analysis of the Indeterminate Structures
⏺8. For Beams, Plane Truss and Frame
▶️Castigliano’s Theorem Slope Deflection method
▶️Moment Distribution method From Influence Line Diagrams (Used for structures having Moving Loads, like Bridges)
▶️Matrix methods
▶️Stiffness method
▶️Flexibility method
⚡️THE END
#Structure
@etconp
➡️The structure should remain in equilibrium after a load is applied to it.
➡️no component of the structure should exhibit motion on the application of load.
➡️If the structure possesses sufficient rigidity to develop reactions in response to the loads applied on it, then the equilibrium of the structure is achieved.
➡️To check whether a structure will be in equilibrium or not, three mathematical equations are developed for two dimensional structures, and six mathematical equations are developed for three-dimensional structures.
🏷For 2-D Structures,
▶️The following 3 conditions should be fulfilled
⏺1. The summation of the forces in the horizontal direction should be zero.
⏺2. The summation of the forces in the vertical direction should be zero.
⏺3. The summation of the moments about the direction perpendicular to both the above forces should be zero.
🏷For 3-D Structures,
The following 6 conditions should be fulfilled
*⃣1. The summation of the forces in the horizontal direction (X ) should be zero
*⃣2. The summation of the forces in the vertical direction( Y ) should be zero
*⃣3. The summation of the forces in the direction perpendicular to both horizontal and vertical directions (Z) should be zero
*⃣4. The summation of the moments in the horizontal direction( X ) should be zero
*⃣5. The summation of the moments in the vertical direction( Y ) should be zero
*⃣6. The summation of the moments about the direction perpendicular to both horizontal and vertical directions (Z) forces should be zero
➡️Equilibrium Conditions for 3D Structural Analysis
▶️The structural analysis can be completed by applying the following step-by-step procedure
⏺1. Idealization of Structure
▶️For structural analysis, idealization of the structural system is done to simplify the structure and making the calculations simpler and easier.
➡️Some of the idealizations that we are aware are list below
⏺We assume the beam as a line structure The joints of a truss are pin jointed. In truss, we assume loads are acting only on joints; the loads acting on members cause bending moments, which is not suitable for the truss And as we have assumed truss to possess pin or hinge joints, it cannot take bending moments.
⏺2. Threats on Structures
▶️The threats on structures are the forces acting on it, which tends to reduce its capacity and stability.
▶️These can be in the form of various loads, as discussed earlier.
*⃣Concentrated load
*⃣Distributed load
*⃣Concentrated moment
*⃣Distributed moment
⏺3. Calculating the response of Structure under the Threat
▶️Response of Structure Internal force (axial, shear or moment) Defection
⏺4. Calculation of Internal Stresses
▶️Internal stresses include: Bending stresses : Caused by the bending moment,Shear stresses Caused by the shear force.
⏺5. Efficiency of the Structure
▶️Efficiency : The structural efficiency is the measure of the mass of a structure to the load it can support safely without excessive deformation and deflections.
▶️If a structure is lighter and supports heavy loads, then its efficiency is deemed higher.
⏺6. Analysis of Determinate Structures
▶️The following methods may be implemented for the analysis of the Determinate Structures, For Beams,
▶️Macaulay’s method ,Moment area method,Conjugate beam method,Consistent Deformation method From Influence Line Diagrams
⏺7. For Plane Truss and Frame:
🚧Method of Joints
🚧Method of Sections
🚧Unit load method From Influence Line Diagrams
⏺8. Analysis of Indeterminate Structures:
▶️Compatibility equations and Principle of Superposition are mostly applied during the analysis of indeterminate structures.
▶️The following methods may be implemented for the analysis of the Indeterminate Structures
⏺8. For Beams, Plane Truss and Frame
▶️Castigliano’s Theorem Slope Deflection method
▶️Moment Distribution method From Influence Line Diagrams (Used for structures having Moving Loads, like Bridges)
▶️Matrix methods
▶️Stiffness method
▶️Flexibility method
⚡️THE END
#Structure
@etconp
Geotechnical Engineering
What’s the minimum water content at which the soil just begins to crumble when it’s rolled into 3 mm diameter threads ?
What’s the minimum water content at which the soil just begins to crumble when it’s rolled into 3 mm diameter threads ?
Anonymous Quiz
52%
Plastic limit
20%
Liquid limit
18%
Shrinkage limit
10%
Plasticity limit
Ethio Construction Engineering
Geotechnical Engineering
What’s the minimum water content at which the soil just begins to crumble when it’s rolled into 3 mm diameter threads ?
What’s the minimum water content at which the soil just begins to crumble when it’s rolled into 3 mm diameter threads ?
GEOTECHNICAL ENGINEERING
what’s the minimum water content at which the soil begins to crumble when it’s rolled into 3mm diameter threads ?
1️⃣. Plastic limit
2️⃣. Liquid limit
3️⃣. Shrinkage limit
4️⃣. Plastic limit
@etconp
Instagram :- https://instagram.com/etconp?igshid=h82z1u7h3leg
Facebook :- https://www.facebook.com/115479406977628/posts/120058029853099/?d=n
Please update your telegram
what’s the minimum water content at which the soil begins to crumble when it’s rolled into 3mm diameter threads ?
1️⃣. Plastic limit
2️⃣. Liquid limit
3️⃣. Shrinkage limit
4️⃣. Plastic limit
@etconp
Instagram :- https://instagram.com/etconp?igshid=h82z1u7h3leg
Facebook :- https://www.facebook.com/115479406977628/posts/120058029853099/?d=n
Please update your telegram
Media is too big
VIEW IN TELEGRAM
👉የውሃ ላይ ተንቀሳቃሽ ከተሞች ያውቃሉ?
🚧እነዚህ ከተሞች እንዴት እንደሚገነቡ በ ምስል የተደገፈ ገለፃ በ ሰሎሞን ቴክ ቶክ ተዘጋጅተዋል።
🚧ቪድዮ ለማየት ከዚህ ፅሁፍ አያይዘንላቹሀል 163.5 MB ስለሆነ WIFI ቢጠቀሙ ይመረጣል።
🎥ወይም በ YOUTUBE ለማየት ከታች ባለው ሊንክ ይከታተሉት
https://youtu.be/Z23Okb1i6-U
Via Tech Talk With Solomon
#ConstructionTechnology
@etconp
🚧እነዚህ ከተሞች እንዴት እንደሚገነቡ በ ምስል የተደገፈ ገለፃ በ ሰሎሞን ቴክ ቶክ ተዘጋጅተዋል።
🚧ቪድዮ ለማየት ከዚህ ፅሁፍ አያይዘንላቹሀል 163.5 MB ስለሆነ WIFI ቢጠቀሙ ይመረጣል።
🎥ወይም በ YOUTUBE ለማየት ከታች ባለው ሊንክ ይከታተሉት
https://youtu.be/Z23Okb1i6-U
Via Tech Talk With Solomon
#ConstructionTechnology
@etconp
This media is not supported in your browser
VIEW IN TELEGRAM
👉Building Resonance
➡️Structural stability during earthquake
➡️Why do some buildings fall in earthquakes?
🚧All buildings have a natural period, or resonance, which is the number of seconds it takes for the building to naturally vibrate back and forth.
🚧The ground also has a specific resonant frequency.
🚧Hard bedrock has higher frequencies softer sediments If the period of ground motion matches the natural resonance of a building, it will undergo the largest oscillations possible and suffer the greatest damage.
🚧A sample demonstration follows the animated portion of this video clip.
@etconp
➡️Structural stability during earthquake
➡️Why do some buildings fall in earthquakes?
🚧All buildings have a natural period, or resonance, which is the number of seconds it takes for the building to naturally vibrate back and forth.
🚧The ground also has a specific resonant frequency.
🚧Hard bedrock has higher frequencies softer sediments If the period of ground motion matches the natural resonance of a building, it will undergo the largest oscillations possible and suffer the greatest damage.
🚧A sample demonstration follows the animated portion of this video clip.
@etconp
👉መሰረት /Foundation/
➡️Foundation
▶️1) ቁፋሮ እና አፈር ሙሌት
⏺መሰረት ሁልጊዜ የተረጋጋ መሬት ላይ ሊቀመጥ ይገባል።
ጥሩ አፈር ካልሆነ በተመረጠ እና ከሌላ ቦታ በመጣ አፈር በሚገባ
ተጠቅጥቆ እና ተደልድሎ ሊቀመጥ ይገባል።
⏺የተመረጠው አፈር ንብርብር/layer/ በየ 25 ሴ᎐ሜ በሚገባ
ሊጠቀጠቅ ወይም ሊደለደል/compact/ ሊደረግ ይገባል።
⏺በሚደለደልበት ወቅት በተወሰነ ረገድ እያንዳንዱን ንብርብር ለተሻለ ጥቅጠቃ እንዲያመች እርጥበት እነዲያገኝ ውሀ ማርከፍከፍ ያስፈልጋል
▶️2) አርማታ ሙሌት እና የብረት ስራ
⏺ቀጭን አርማታ/lean Concrete/ ከተመረጠው አፈር ሙሌት በላይ ሊደረግ ይገባል እንደ አስፈላጊነቱም እርጥበተ መከላከያ/water proof/ ሊደረግ ይችላል።
⏺አርማታ ሙሌት ለመሰረት፣ ቢም፣ ኮለን እና ወለል ስራ የአርማታ ጥንካሬ በትንሹ C25 ሊኖረው ይገባል በተጨማሪ እንደ ስትራክቸራል ዲዛይኑ ሊለያይ ይችላል።
⏺የቢም ብረት የላይኛው ብረት መሀል ላይ የታችኛው ደግሞ ኮለን ድጋፍ/support/ ላይ ሊሆን ይገባል እንዲሁም ማት ፋውንዴሽን ላይ የዚህ ተቃራኒ ይሆናል።
⏺ብረት 4D የብረቱን ውፍረት በአራት በማባዛት የሚሰጠንን ርዝመት በመደረብ መተላለፍ ይተበቅበታል።
⏺ዲዛይን ላይ በተቆራረጠ መስመር /hidden line የሚቀመጡ ብረቶች ሁልጊዜ የታች ብረት ሆነው ይቀመጣሉ።
⏺የአርማታ ሽፋን/concrete cover/አብዛኛውን ግዜ 5ሴ᎐ሜ ይሆናል ከመሬት በላይ ግን በ 2᎐5ሴ.ሜ ይሰራል።
⏺በአርማታ ወይም በብረት የሚሰራ ክፍተት መስጫ spacer/ ልንጠቀም ይገባል።
⚡️ይቀጥላል ...
#Foundation
@etconp
➡️Foundation
▶️1) ቁፋሮ እና አፈር ሙሌት
⏺መሰረት ሁልጊዜ የተረጋጋ መሬት ላይ ሊቀመጥ ይገባል።
ጥሩ አፈር ካልሆነ በተመረጠ እና ከሌላ ቦታ በመጣ አፈር በሚገባ
ተጠቅጥቆ እና ተደልድሎ ሊቀመጥ ይገባል።
⏺የተመረጠው አፈር ንብርብር/layer/ በየ 25 ሴ᎐ሜ በሚገባ
ሊጠቀጠቅ ወይም ሊደለደል/compact/ ሊደረግ ይገባል።
⏺በሚደለደልበት ወቅት በተወሰነ ረገድ እያንዳንዱን ንብርብር ለተሻለ ጥቅጠቃ እንዲያመች እርጥበት እነዲያገኝ ውሀ ማርከፍከፍ ያስፈልጋል
▶️2) አርማታ ሙሌት እና የብረት ስራ
⏺ቀጭን አርማታ/lean Concrete/ ከተመረጠው አፈር ሙሌት በላይ ሊደረግ ይገባል እንደ አስፈላጊነቱም እርጥበተ መከላከያ/water proof/ ሊደረግ ይችላል።
⏺አርማታ ሙሌት ለመሰረት፣ ቢም፣ ኮለን እና ወለል ስራ የአርማታ ጥንካሬ በትንሹ C25 ሊኖረው ይገባል በተጨማሪ እንደ ስትራክቸራል ዲዛይኑ ሊለያይ ይችላል።
⏺የቢም ብረት የላይኛው ብረት መሀል ላይ የታችኛው ደግሞ ኮለን ድጋፍ/support/ ላይ ሊሆን ይገባል እንዲሁም ማት ፋውንዴሽን ላይ የዚህ ተቃራኒ ይሆናል።
⏺ብረት 4D የብረቱን ውፍረት በአራት በማባዛት የሚሰጠንን ርዝመት በመደረብ መተላለፍ ይተበቅበታል።
⏺ዲዛይን ላይ በተቆራረጠ መስመር /hidden line የሚቀመጡ ብረቶች ሁልጊዜ የታች ብረት ሆነው ይቀመጣሉ።
⏺የአርማታ ሽፋን/concrete cover/አብዛኛውን ግዜ 5ሴ᎐ሜ ይሆናል ከመሬት በላይ ግን በ 2᎐5ሴ.ሜ ይሰራል።
⏺በአርማታ ወይም በብረት የሚሰራ ክፍተት መስጫ spacer/ ልንጠቀም ይገባል።
⚡️ይቀጥላል ...
#Foundation
@etconp