⚡👆👆👆👆👆👆👆
👉AUTO CAD SHORT CUTS @COTMp
👉AUTO CAD SHORT CUTS @COTMp
👉ውድ የ @COTMp ቤተሰቦች ለ ዛሬ ደሞ Beam design ኣዘጋጅተናል👇👇👇
.
✳️ Beam design( flexure) example according to ES EN 1992-1-1: 2015
➡️ Material Data
Concrete grade:- C30/37(fck=30 Mpa).
Steel grade:- S500 ( fyk=500 Mpa).
➡️ Beam geometry
Type:- Simply supported beam
Effective length of beam:- 6 m.
Beam width(b):- 250 mm.
➡️ Load
Dead load(Gk):- self weight of Beam plus 10 KN/m super imposed load.
Live Load(Qk):- 8 KN/m
Depth is not limited by any requirement( singly reinforced beam is possible).
@COTMp 👇
.
✳️ Beam design( flexure) example according to ES EN 1992-1-1: 2015
➡️ Material Data
Concrete grade:- C30/37(fck=30 Mpa).
Steel grade:- S500 ( fyk=500 Mpa).
➡️ Beam geometry
Type:- Simply supported beam
Effective length of beam:- 6 m.
Beam width(b):- 250 mm.
➡️ Load
Dead load(Gk):- self weight of Beam plus 10 KN/m super imposed load.
Live Load(Qk):- 8 KN/m
Depth is not limited by any requirement( singly reinforced beam is possible).
@COTMp 👇
Design Step 1: depth from deflection( deformation) control
👉Since C30/37 concrete is used the limiting span to depth ratio from table 7.4 N Is 14 ( the beam is assumed to be highly stressed with ρ=1.5 %).
👉The limiting depth to prevent excessive deformation is:
👉d=le/14 ....where le is effective length of beam.
👉d=6000 mm/14=428.57 mm
Design step 2:- cover to reinforcement
👉Exposure class is assumed to be XC 1 and the value of Cmin,dur becomes 15 mm.
👉 for separate bar, the value of Cmin,b is equals to the diameter of bar( φ). Assuming φ=20 mm, and Cmin,b=20 mm.
➡️Cₘᵢₙ= max {Cₘᵢₙ,b ; Cₘᵢₙ,dᵤᵣ; 10 mm }
➡️Cₘᵢₙ=max{20 mm,15 mm, 10 mm}
➡️Cₘᵢₙ=20 mm
And the nominal cover becomes
➡️Cnom=Cmin+10=20+10=30 mm cover.
Design step 3:- overall depth
For stirrup assume 8 mm bars.
👉D=d+cover +φₛ+φₗ/2
👉D=428.57mm+30mm+8+20/2=476.57 mm
For ease of construction take D=500 mm ( nearest 50 ).
Design step 4:- Load calculation
Dead load
👉 self weight of beam
Unit weight of concrete(γ)= 25 KN/m³
Weight per meter:-
➡️γ*b*D
➡️25*0.25 *0.5=3.125 KN/m
👉 total dead load
Superimposed+self weight=10KN/m+3.125 KN/m=13.125 KN/M.
Design Load
Pd=1.35Gk+1.5Qk
Pd=1.35*13.125+1.5*8=29.72 KN/m.
.
@COTMp 👇
👉Since C30/37 concrete is used the limiting span to depth ratio from table 7.4 N Is 14 ( the beam is assumed to be highly stressed with ρ=1.5 %).
👉The limiting depth to prevent excessive deformation is:
👉d=le/14 ....where le is effective length of beam.
👉d=6000 mm/14=428.57 mm
Design step 2:- cover to reinforcement
👉Exposure class is assumed to be XC 1 and the value of Cmin,dur becomes 15 mm.
👉 for separate bar, the value of Cmin,b is equals to the diameter of bar( φ). Assuming φ=20 mm, and Cmin,b=20 mm.
➡️Cₘᵢₙ= max {Cₘᵢₙ,b ; Cₘᵢₙ,dᵤᵣ; 10 mm }
➡️Cₘᵢₙ=max{20 mm,15 mm, 10 mm}
➡️Cₘᵢₙ=20 mm
And the nominal cover becomes
➡️Cnom=Cmin+10=20+10=30 mm cover.
Design step 3:- overall depth
For stirrup assume 8 mm bars.
👉D=d+cover +φₛ+φₗ/2
👉D=428.57mm+30mm+8+20/2=476.57 mm
For ease of construction take D=500 mm ( nearest 50 ).
Design step 4:- Load calculation
Dead load
👉 self weight of beam
Unit weight of concrete(γ)= 25 KN/m³
Weight per meter:-
➡️γ*b*D
➡️25*0.25 *0.5=3.125 KN/m
👉 total dead load
Superimposed+self weight=10KN/m+3.125 KN/m=13.125 KN/M.
Design Load
Pd=1.35Gk+1.5Qk
Pd=1.35*13.125+1.5*8=29.72 KN/m.
.
@COTMp 👇
👍2
Design step 5:-design strength of material
Concrete(fcd)
👉fcd=αcc*fck/γc
👉for C30/37 concrete fck is 30 Mpa.
👉αcc=0.85
👉γc=1.5
👉fcd=(0.85*30/1.5)=17 Mpa
Steel (fyd)
👉fyd=fyk/γs
👉γs=1.15
👉fyd=500/1.15=434.78 Mpa
Design step 6:- design moment calculation
👉 for simply supported beam the maximum moment occurs at mid span and it's vale is
➡️Mmax=Msd=Pd*L²/8
➡️Mmax=Msd=(29.72)*(6²)/8=133.73 KN-m
Design step 6:- check depth for flexure
👉effective depth of beam in order to be singly reinforced is calculated from
✓d=sqrt(Msd/(μsd*fcd*b))
✓Sqrt...[square root of ]
For zero percent redistribution of moment the limiting μsd is 0.295.
d=sqrt({133.73*10⁶}/{0.295*17*250})=326.59 mm
And the provided effective depth:
d= 500 - 30 - 8 - 20/2 = 452 mm
Since the provided depth is greater than calculated from flexure, depth is ok!
Design step 7:- Reinforcement calculation
Using design chart method
✓μsd={Msd*10⁶}/{fcd*b*d²)
✓μsd={133.73*10⁶}/{17*250*452²}=0.154 <0.295 ok!
from design chart the value of kz is
✓kz=0.92
and z( moment arm , the distance between Cc and Ts)
✓Z=kz*d=0.92*452=415.84 mm
Now the amount of reinforcement
✓As={Msd}/{Z*fyd}
✓As={133.73*10⁶}/{415.84*434.77}=739.65 mm²
.
@COTMp 👇
Concrete(fcd)
👉fcd=αcc*fck/γc
👉for C30/37 concrete fck is 30 Mpa.
👉αcc=0.85
👉γc=1.5
👉fcd=(0.85*30/1.5)=17 Mpa
Steel (fyd)
👉fyd=fyk/γs
👉γs=1.15
👉fyd=500/1.15=434.78 Mpa
Design step 6:- design moment calculation
👉 for simply supported beam the maximum moment occurs at mid span and it's vale is
➡️Mmax=Msd=Pd*L²/8
➡️Mmax=Msd=(29.72)*(6²)/8=133.73 KN-m
Design step 6:- check depth for flexure
👉effective depth of beam in order to be singly reinforced is calculated from
✓d=sqrt(Msd/(μsd*fcd*b))
✓Sqrt...[square root of ]
For zero percent redistribution of moment the limiting μsd is 0.295.
d=sqrt({133.73*10⁶}/{0.295*17*250})=326.59 mm
And the provided effective depth:
d= 500 - 30 - 8 - 20/2 = 452 mm
Since the provided depth is greater than calculated from flexure, depth is ok!
Design step 7:- Reinforcement calculation
Using design chart method
✓μsd={Msd*10⁶}/{fcd*b*d²)
✓μsd={133.73*10⁶}/{17*250*452²}=0.154 <0.295 ok!
from design chart the value of kz is
✓kz=0.92
and z( moment arm , the distance between Cc and Ts)
✓Z=kz*d=0.92*452=415.84 mm
Now the amount of reinforcement
✓As={Msd}/{Z*fyd}
✓As={133.73*10⁶}/{415.84*434.77}=739.65 mm²
.
@COTMp 👇
👍1
Design step 8:- check for minimum and maximum longitudinal reinforcement
Minimum reinforcement
✅As,min=0.26{fctm/fyk}bt*d. ( ES EN 1992-1-1:2015 equation 9.1 N)
✅From table 3.1 of ES EN 1992-1-1:2015 the value of fctm for C30/37 concrete is 2.9 Mpa.
👉As,min=0.26*{2.6/500}*250*452=152.776 mm²
👉As> As,min....provide As
Maximum reinforcement
ES EN 1992-1-1:2015 Article 9.2.1.1[3] " the cross sectional area of tension or compression reinforcement should not exceed 0.04Ac" and the national annex recommends the same value.
As,max=0.04*250*500=5000 mm²
As< As,max.....ok!
Design step 9:- calculate the number of bars
👉# of bars=As/as
Where
👉As calculated area of reinforcement
👉as is the area of one bar
👉as=(πφ²/4)=(π*20²/4)≈314 mm²
of bar=(739.65/314)=2.355≈3
🚩provide 3φ20 bars
.
@COTMp ... Finally 👇
Minimum reinforcement
✅As,min=0.26{fctm/fyk}bt*d. ( ES EN 1992-1-1:2015 equation 9.1 N)
✅From table 3.1 of ES EN 1992-1-1:2015 the value of fctm for C30/37 concrete is 2.9 Mpa.
👉As,min=0.26*{2.6/500}*250*452=152.776 mm²
👉As> As,min....provide As
Maximum reinforcement
ES EN 1992-1-1:2015 Article 9.2.1.1[3] " the cross sectional area of tension or compression reinforcement should not exceed 0.04Ac" and the national annex recommends the same value.
As,max=0.04*250*500=5000 mm²
As< As,max.....ok!
Design step 9:- calculate the number of bars
👉# of bars=As/as
Where
👉As calculated area of reinforcement
👉as is the area of one bar
👉as=(πφ²/4)=(π*20²/4)≈314 mm²
of bar=(739.65/314)=2.355≈3
🚩provide 3φ20 bars
.
@COTMp ... Finally 👇
👉 beam section detail
➡ All dimensions are in centimetres
➡ The two bars at the top are nominal reinforcement to hang the stirrups( the blue lines).
.
👏THANK YOU @COTMp
➡ All dimensions are in centimetres
➡ The two bars at the top are nominal reinforcement to hang the stirrups( the blue lines).
.
👏THANK YOU @COTMp
👆👆👆👆👆👆👆
👉ውድ የ @COTMp ቤተሰቦች ዛሬ ደሞ በጠየቃችሁን መሰረት ስለ ቢም ዲዛይን ማለትም ኣንድ የተሰራ ( Example Of Beam Design) ኣዘጋጅተናል።እናመሰግናለን።
.
⚡SHARE SHARE SHARE
👉ውድ የ @COTMp ቤተሰቦች ዛሬ ደሞ በጠየቃችሁን መሰረት ስለ ቢም ዲዛይን ማለትም ኣንድ የተሰራ ( Example Of Beam Design) ኣዘጋጅተናል።እናመሰግናለን።
.
⚡SHARE SHARE SHARE
👉ውድ የ @COTMp ተከታዮች ቻናላችን ቅድም Beam Design ኣይተናል ለ ነገ ሊቀርብላቹ እምትፈልጉትን Design ምረጡ።
👇👇👇👇👇
.
👍)Footing ✔)Shear
👇👇👇👇👇
.
👍)Footing ✔)Shear
👉ይህ የምትመለከቱት ቤት በ ኣብዛኛው በ ትግራይ ክልል የ ገጠሪቱ ክፍል የሚገኝ ሲሆን "ህድሞ" በመባል ይታወቃል።
.
🚩የኋላው ከሌለ የለም የፊቱ✌
.
⚡ሼር በማድረግ @COTMP ያጋሩ።
.
🚩የኋላው ከሌለ የለም የፊቱ✌
.
⚡ሼር በማድረግ @COTMP ያጋሩ።